• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.6
• /
• pp.557-564
• /
• 2019

The characteristics of the torque and torque ripple of Interior Permanent Magnet Synchronous Motor(IPMSM) are influenced by the size and position of the rotor magnet and the size of the stator slot. This paper deals with the optimal design method for improving torque and torque ripplerate for IPMSM using Response Surface Methodology(RSM). Two objective functions of torque output and torque ripple were derived from the sensitivity analysis by Plackett-Burmann(PB) for the characteristic variables affecting torque and torque ripple. Secondary characteristic variables were selected from the derived objective function and RSM secondary regression model function was estimated by the experiment schedule and analysis results according to the Central Composite Design (CCD). The reliability of the secondary regression model was verified using ANOVA table. The analysis according to the experimental schedule was verified by JMAG(Ver. 18.0) which is Finite Element Method(FEM) software. The torque output of IPMSM applied with final characteristic variables was increased torque output by 11.5 % and the torque ripplerate was reduced by 9.1 %.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.46 no.3
• /
• pp.248-252
• /
• 2001

Near infrared spectroscopy (NIRS) is a rapid and accurate analytical method for determining the composition of agricultural products and feeds. An important merit of the NIRS analytical system is consistent predictions across instruments. However, proper calibration is the most important factor for a NIRS analytical system. Forty samples were obtained from Kyonggi-do Agricultural Research and Extension Services, and used to develop calibrations for crude protein content and crude oil content. Calibrations equations were developed using multiple linear regression (MLR). Accuracy and precision of NIRS predictions were adequate for quality measurement for the two constituents in kidney bean seed. In calibration sample sets (N=30), multiple correlation coefficient between NIR and lab measurements is 0.90 for seed, 0.97 for powder in seed protein concentration and 0.40 for seed and 0.92 for powder in seed oil concentration, respectively. It is concluded that NIRS method is suitable for the determination of seed composition in whole kidney bean.

• Journal of the Korean Ceramic Society
• /
• v.35 no.3
• /
• pp.280-286
• /
• 1998

LaAlO3 Single crystals used as a substrate for thin film depositions of a high temperature oxide su-perconductor YB2Cu3O7 and applied to microwave frequencies were grown by the Traveling Solvent Flati-ing Zone (TSFZ) method and characterized. For the growth of LaAlO3 single crystals polycrystalline fe-edrods were prepared from powder mixture of La2O3 and Al2O3 with a mole ratio of 1:1 calcined at 110$0^{\circ}C$ for 3h and sintered at 140$0^{\circ}C$ for 4h The growth LaAlO3 crystals was 4-5mm in diameter 30mm in length and dark brown. The growth rate was 2-3mm/h and the rotation speeds were 10rpm for an upper ro-tation and 40 rpm for a lower rotation The growing crystals and the feedrods were counter-rotated. The orientation of the grown single crystals of LaAlO3 was identified to be [111] direction. Dielectric constants were measured to be 30-33 between 100 kHz and 1 MHz in the 30$0^{\circ}C$ to 45$0^{\circ}C$ temperature range and 102 in a range of 100 kHz at the phase transformation temperature of 522$^{\circ}C$ Dielectric losses were calculated to be 1.8$\times$10-4 at the room temperature and 5.7$\times$10-3 at the phase transformation temperature. Lattice con-stants of the grown crystlals were determined to be aR=5.3806 $\AA$ and $\alpha$=60.043$^{\circ}$ by the least square method.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07b
• /
• pp.965-968
• /
• 2004

Effective transverse Piezoelectric Coefficients $(e_{31,f})$ of thick PZT $(Pb(Zr_{0.52}Ti{0.48}Ti_{0.48})O_3)$ films on $SiN_x/Si$ substrates were measured with PZT thicknesses and top electrode dimensions. $e_{31,f}$ is one of important Parameters characterizing Piezoelectricity of PZT films. Thick PZT films have been used as various sensors and actuators because of their high driving force and high breakdown voltage. Thick PZT films were fabricated on Pt/Ta/$SiN_x$/Si substrates using sol-gel method. Thicknesses of PZT films were $1{\mu}m$ and $1.8{\mu}m$. $|e_{31,f}|$ values of $1.8{\mu}m$-thick-PZT films were higher than those of $1{\mu}$-thick-PZT films. Maximum $|e_{31,f}|$ of $1.8{\mu}$-thick-PZT films was about $50^{\circ}C/m^2$.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.23 no.7 s.166
• /
• pp.1112-1119
• /
• 1999

Fracture resistance(J-R) curves, which are used for the elastic-plastic fracture mechanics analyses, are known to be dependent on the cyclic loading history. The objective of this paper is to study the effect of reverse cyclic loading on J-R curves in CT specimens. The effect of two parameters was observed on the J-R curves during the reverse cyclic loading. One was the minimum-to-maximum load ratio(R) and the other was the incremental plastic displacement(${\delta}_{cycle}/{\delta}_i$), which is related to the amount of crack growth that occurs in a cycle. Fracture resistance test on CT specimens with varying load ratio and incremental plastic displacement were performed. For the SA 516 Gr. 70 steel, the results showed that the J-R curves were decreased with decreasing the load ratio and the incremental plastic displacement. When the load ratio was set to -1, the results of the J-R curves and the $J_i$ value were about $40{\sim}50$ percent of those for the monotonic loading condition. Also on condition that the incremental plastic displacement reached 1/40, the J-R curves and the $J_i$ value were about $50{\sim}60$ percent of those for the incremental plastic displacement of 1/10.

• Journal of Mushroom
• /
• v.1 no.1
• /
• pp.9-14
• /
• 2003

To breed new superior strains, collected strains were characterized and then several white strains were selected as parents. Monokaryons from the parents were isolated and studied. All tested white strains showed same mating genotype. Growth rate of monokaryons were lower than collected dikaryons. New dikaryotic strains were derived from inbreeding method, which means mating between monokaryotic isolates from different white strains having same mating genotype. Some of them showed higher yields of fruitbody than their parents. Specially Fv 4-1 strain showed the best productivity. Furthermore some mating combination showed cytoplasmic effect, when they mated reciprocally.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.21 no.5
• /
• pp.549-555
• /
• 2001

Ultrasonic is a powerful nondestructive technique for getting the information of flaws and material properties of in-services facilities. We prepared 4 different 1Cr-1Mo-0.25V specimens by Isothermal aging at $630^{\circ}C$. We evaluated material degradation using ultrasonic parameters, velocity, attenuation and harmonic generation. Attenuation and nonlinear parameter derived from harmonic generation efficiency increased as degradation. Especially the second harmonic of the fundamental wave in the 1,820h aging material was observed to exceed 20dB more than that in the un-aged material. But velocity remained virtually the same for all specimens. We concluded that nonlinear parameter and attenuation are sensitive to material degradation, but velocity was not. It'll be a good parameter for evaluating the material degradation.

• Analytical Science and Technology
• /
• v.23 no.3
• /
• pp.233-239
• /
• 2010

Pure macroporous silica matrix using a template of polystyrene (PS) was prepared by the sol-gel method. Macroporous Ag-$SiO_2$ composite materials, which were homogeneously dispersed with Ag particles in the macropores, were successfully fabricated. The pure porous silica had ordered pore sizes of 100 nm and 200 nm, which was adjusted under consideration of the template size. The macroporous Ag-$SiO_2$ composite showed the ideal ordered distribution of the pore in case of the adding of 3 wt% $AgNO_3$ under consideration of controlling of the pore size as well as microstructural observation of $AgNO_3$concentration. The macroporous Ag-$SiO_2$ composites had ordered 100 nm and 200 nm pores, and the Ag particles within the matrix showed the size of 15~20 nm.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.10
• /
• pp.1163-1169
• /
• 2012

Rubber, a hyperelastic material, is the main material used in tires. During the operation of a car, the tire receives various types of loads. The accumulation of strain energy due to such loads induces tire failure. Generally, because rubber materials used for tires have stress softening characteristics, unlike metals, test methods used for metals cannot be applied to rubber. Therefore, in this study, for the evaluation of the fatigue properties of two types of specimens that have different material components, a tensile test and a fatigue test according to the extended strain range dissimilar to ASTM D4482 are performed, and fatigue life equations are proposed based on the test results.

• Korean Journal of Metals and Materials
• /
• v.50 no.3
• /
• pp.206-211
• /
• 2012

Graphene has recently received high attention as a promising material for various applications, and many related studies have been undertaken to reveal its basic mechanical properties. However, the tribological properties of graphene film fabricated by the chemical vapor deposition (CVD) method are barely known. In this study, the contact angle and frictional wear characteristics of graphene coated copper film were investigated under room temperature, normal air pressure, and no lubrication condition. The contact angle was measured by sessile drop method and the wear test was carried out under normal loads of 660 mN and 2940 mN, respectively. The tribological behaviors of a graphene coating layer were also examined. Compared to heat treated bare copper foil, the graphene coated one shows a higher contact angle and lower friction coefficient.