• Journal of the Korean Society for Railway
• /
• v.12 no.2
• /
• pp.230-235
• /
• 2009

We have conducted an experimental study to analyze characteristics of the wheel profile wear and an influence of the wheel flange wear on the vehicle's vibration characteristics. In experiment with EMU, wheel profile wear is severe at the beginning of the commercial operation. In this stage, the variations of the wheel dimension parameters and equivalent conicity is changed rapidly. Along with a mileage of the test vehicle, the wear of the wheel flange is increased and also the vibration level of the car-body is increased. The peak-peak mean value of the body vibration is estimated as good level, but the level is approached at the limit of the good level as mileage increases. Especially, the peak-peak maximum value of the body vibration shows the distinct increase of vibration level.

• Journal of the Korean Society for Railway
• /
• v.10 no.6
• /
• pp.772-778
• /
• 2007

For the wear characteristics assessment of Saemaul train passing through curves, an analysis model for multi-car system has been developed. By using this model and ADAMS/Rail, sensitivity analyses have been conducted for the wear characteristics by changing the related parameters. At low speed, the wear number and the sliding mean of right wheel showed higher than left wheel, while those of left wheel showed higher than right wheel at high speed. According to the decrease of curve radius, the wear number and the sliding mean were increased. When the length of transition curve was increased, the wear number and the sliding mean was increased. And according to increase of cant, the wear number and the sliding mean were increased.

• Journal of the Korean Society for Railway
• /
• v.20 no.4
• /
• pp.512-520
• /
• 2017

On a typical railway, trains travel using the friction between the wheel and the rail. Contact pressure is generated between the wheel and the rail, and the magnitude of the contact pressure changes depending on the weight, speed, wheel-set hunting, and contact point of the vehicle. In this study, the contact characteristics were analyzed through the finite element analysis for the wheel/rail system on curved track, and fatigue damage and wear rate of wheel/rail according to contact pressure were analyzed through rolling contact fatigue test. Results indicate that, general and heat treated rails showed higher wear rate than wheels, and general and heat treated rail wear rate increased rapidly over a certain number of repetitions. In addition, the general rail wear rate was about 7 ~ 15% higher than that of the heat treated rail, and a regression equation for the rail wear rate with the contact pressure in the contact pressure range of 900 ~ 1,500 MPa was presented.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2009.10a
• /
• pp.765-766
• /
• 2009

• Proceedings of the KSR Conference
• /
• 2007.05a
• /
• pp.1344-1368
• /
• 2007

The Advanced countries including Japan, USA and European countries are adopting automatic system(e.g., auto-measurement using CCD camera) for measuring pantograph sliding plate and wheel abrasion to minimize manpower for E.M.U(Electric Multiple Unit) inspection and maintenance as part of management rationalization of railroad Corporation since late 1980's. In Korea, as part of scheme of business rationalization, automatic system for measuring pantograph sliding plate and wheel abrasion started to draw industry attention since late 1990s, and the system started to be installed in newly built depots of Korea Railroad Corporation since 2002. This study hopefully provides the base for realizing business rationalization and applying the advanced technology developed by Korea, the country of powerful IT basis, to overseas railroad organizations by examining automatic system for measuring pantograph sliding plate abrasion using existing CCD cameras produced domestically and in foreign countries to study cases(organizations in Korea) for improvement of measurement, management and inspection of pantograph sliding plate abrasion using CCD cameras with new cutting-edge technology; and by applying the study result to railroad organizations in metropolitan areas in Korea.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2011.04a
• /
• pp.493-498
• /
• 2011

구름접촉피로는 차륜과 레일의 반복적인 접촉으로 인하여 발생하는 표면손상현상으로 점차 증가하는 레일손상 중 하나이다. 접촉마모 및 주기적 그라인딩보다 균열의 성장속도가 더 빨라 균열진전이 시작되는 최소균열크기(minimum crack size for growth)는 레일의 파괴방지 및 유효한 유지보수전략을 수립하는데 기초자료로 활용된다. 본 연구에서는 최소균열크기를 예측하기 위하여 차륜레일의 접촉에 영향을 미치는 주요 파라미터를 변화시키면서 최소균열크기의 변화를 살펴보았다. 이를 위하여 Fletcher와 Kapoor의 "2.5D"모델을 적용한 시뮬레이션 소프트웨어를 개발하였으며, 최대접촉하중(1174MPa), 표면마찰계수(0.1, 0.2, 0.3 and 0.4), 잔류응력, 접촉에 의한 표면마모(1.0nm/cycle), 그라인딩량(0.3mm/10MGT)을 파라미터로 하여 해석을 수행하였다. 해석결과 최소균열크기는 해석조건에 따라 1.41-1.95mm로 계산되었다.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.854-859
• /
• 2008

In a railway vehicle, contact between wheel and rail is a peculiar characteristic and variations of wheel and rail profile influence on the dynamic characteristics of railway vehicle. Thus the variations of the wheel and rail profile are very important in railway dynamics. Recently a research relating to active steering to improve the curving performance of vehicle is progressing actively at home and abroad. In this field, a pre-study for the wheel/rail contact geometry is needed and especially the variation of the wheel/rail contact geometry with wheel wear is the key design parameter to develop the controller of the active steering bogie. In this paper, we have experimentally studied to analyze the variation of the wheel/rail contact geometry with wheel wear as a pre-study to develop the active steering bogie for electric multiple unit (EMU). For this, we have made an experiment with EMU operating in curving area. We have measured the wear profiles of the wheel of the test vehicle and analyzed the wheel/rail contact geometry with a mileage of the test vehicle. In experiment with test vehicle, we have got the useful data to design the steering controller of the wheelset.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.11
• /
• pp.1387-1395
• /
• 2013

When the center of mass of a railway wheel is not aligned with the geometrical center of the wheel axis, wheel unbalance occurs. If a railway vehicle runs without removing the wheel unbalance, vibrations will be produced. This will also cause wear and damage of the axle bearing. In this study, dynamic analysis of a railway vehicle with wheel unbalance was conducted to examine the reduction in critical speed and the resonance of the car-body and the effect on the magnitude of wheel unbalance was examined. In addition, the calculation of the car-body vibration owing to static and dynamic unbalance in the railway wheel shows that two-plane balancing is necessary.

• Journal of the Korean Society for Railway
• /
• v.11 no.6
• /
• pp.524-529
• /
• 2008

The damaged wheel in railway vehicle would cause a poor ride comfort, a rise in the maintenance cost and even fracture of the wheel, which then leads to a tremendous social and economical cost. The defect initiation and crack propagation in wheel may result in the damage of the railway vehicle or derailment. Therefore, it is important to evaluate the characteristics of the wheel tread. In the present paper, the characteristics of wheel tread based on contact positions, running distance and brake pattern are evaluated. The result shows that the damaged wheel tread is remarkably depended on the contact positions between wheel and rail.

• Journal of the Korean Society for Precision Engineering
• /
• v.29 no.6
• /
• pp.607-612
• /
• 2012

The wear problem of wheel flange occurs at sharp curves of rail. This paper proposes a procedure for optimum design of a wheel profile wherein flange wear is reduced by improving an interaction between wheel and rail. Application of optimization method to design problem mainly depends on characteristics of design space. This paper compared local optimization method with global optimization according to sensitivity value of objective function for design variables to find out which optimization method is appropriable to minimize wear of wheel flange. Wheel profile is created by a piecewise cubic Hermite interpolating polynomial and dynamic performances are analyzed by a railway dynamic analysis program, VAMPIRE. From the optimization results, it is verified that the global optimization method such as genetic algorithm is more suitable to wheel profile optimization than the local optimization of SQP (Sequential Quadratic Programming) in case of considering the lack of empirical knowledge for initial design value.