• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.26 no.6_spc
• /
• pp.644-650
• /
• 2016

Track maintenance works based on track geometry recordings are essential to enhance the safety and comfort of railway transportation. Usually, the track irregularity has been measured by a special inspection trains which all were imported from abroad. Because the inspection train speed is limited under 160 km/h, it takes a long time to inspect railways and there is difficulty in daytime operation. To solve this problem, we started to develop a track geometry measuring system (TGMS) with measurement speed up to 300 km/h which can be installed in commercial vehicles such as HEMU-430X. In this paper, we introduce a newly developed inertial TGMS and propose two inertial navigation system (INS) algorithms (method A, B) for measuring track geometry. In order to investigate advantage and disadvantage of each algorithm, we performed vibration test of the TGMS, which was simulated by 6-axis shaking table. Through the vibration test, we analyzed the influence of vehicle vibration on the TGMS which will be installed on bogie frame. To the vibration test, two methods satisfied the required accuracy of track geometry measurement under the level of the actual vehicle vibration of HEMU-430X train. Theoretically, method A is sensitive to vehicle vibration than method B. However, HEMU-430X's bogie vibration frequency range is out of interest range of measurement system. Therefore, method A can also apply the HEMU-430X train.

• Journal of Institute of Control, Robotics and Systems
• /
• v.18 no.7
• /
• pp.688-698
• /
• 2012

This paper deals with ROLSO (Reduced Order Luenberger State Observer) design to prevent jackknifing phenomenon of articulated vehicles consisting of the tractor and semi-trailer by using GPS. In addition, by applying the regulator system using ROLSO feedback system, simulation's result presents that articulated vehicle's states are stabilized than the human's PR time (Preception Response time) rapidly. This simulation verifies that the automatic control of articulated vehicle's can be applied for the accident prevention for the time that the driver is unable to manage with the sudden accident. For this simulation, by using the equation of planar motion, the modeling of the articulated vehicle was performed. This modeling was expressed in the state space model. And FOLSO (Full Order Luenberger State Observer), ROLSO were designed by using the state space model of an articulated vehicle's dynamics.

• Journal of Advanced Navigation Technology
• /
• v.11 no.4
• /
• pp.378-387
• /
• 2007

In this paper, Authors develop and verify the algorithm for enhancing the performance of Unmanned vehicle's Autonomous navigation, and also propose the method of establishing much more precise Navigation locus. Unmanned vehicle has a destination, however orientation is not notified, which make it find the future orientation itself. Extended Kalman Filter make it access to the desirable direction, which coupled with INS and GPS is proposed in this paper. Sliding mode control could overcome the side slip and lateral minor movement of the vehicle. The test result would shows the effectiveness of Extended kalman filter and Slide mode control for the navigation.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.40 no.11
• /
• pp.2261-2270
• /
• 2015

GIS(Geographic Information System) based Positioning technique uses geographic information to predict which satellites are visible or invisible. GPS positioning has poor positioning accuracy in dense urban area where tall buildings block the satellite signals. In this paper, we proposed GIS based Advanced Positioning technique of Mobile GPS to resolve this problem. Particularly, this technique improves positioning accuracy in dense urban area. It is consist of ephemeris and GIS server. We will inversely estimate pseudorange by using NMEA-0183 output data of mobile GPS. After that, we can find more accurate position by using ephemeris and GIS information.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.9 no.2
• /
• pp.454-461
• /
• 2005

Car navigation system which is killer application fuses map management techniques into CPS techniques. Even if the existing navigation systems are designed for the shortest path, they are not able to cope efficiently with the change of the traffic flow and the bottleneck point of road. Therefore, it is necessary to find out shortest path algorithm based on time instead of distance which takes traffic information into consideration. In this paper, we propose a optimal path search algorithm based on the traffic information. More precisely. we introduce the system architecture for finding out optimal paths, and the limitations of the existing shortest path search algorithm are also analyzed. And then, we propose a new algorithm for finding out optimal path to make good use of the orientation of the collected traffic information.

• Journal of Institute of Control, Robotics and Systems
• /
• v.12 no.2
• /
• pp.106-112
• /
• 2006

A new model for the continuous-magnetic interferences has been proposed in this paper to remove external interferes of magnetic field to the dual electric compass. By this removal, the dual electric compass can be used for proving the azimuth angle in an automobile navigation system instead of the rate gyroscope. In the navigation system with a GPS receiver, a DR sensor such as a rate gyroscope is needed to overcome the shielded areas, which is relatively expensive and requires frequent calibrations. However the dual electric compass designed by this research is cheap and provides absolute azimuth angle precisely, which is beneficiary to be used as a DR sensor. The main contribution of this paper is that the long-lasting magnetic interferences have been removed out by using the proposed model, which never be studied before. With a hybrid navigation system using a DR sensor, we demonstrated that dual electric compass is better than a rate gyroscope in terms of both economics and performances.

• Journal of the Korean Society for Precision Engineering
• /
• v.26 no.6
• /
• pp.74-80
• /
• 2009

Path tracking of unmanned vehicle is a basis of autonomous driving and navigation. For the path tracking, it is very important to find the exact position of a vehicle. GPS is used to get the position of vehicle and a direction sensor and a velocity sensor is used to compensate the position error of GPS. To detect path lines in a road image, the bird's eye view transform is employed, which makes it easy to design a lateral control algorithm simply than from the perspective view of image. Because the driving speed of vehicle should be decreased at a curved lane and crossroads, so we suggest the speed control algorithm used GPS and image data. The control algorithm is simulated and experimented from the basis of expert driver's knowledge data. In the experiments, the results show that bird's eye view transform are good for the steering control and a speed control algorithm also shows a stability in real driving.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.3
• /
• pp.220-227
• /
• 2014

This paper presents about multi-rate sensors' synchronization and filter fusion via a sigmoid function of the Kalman filter. To synchronize multi-rate sensors, the estimation states of the Kalman filter is modified. A specific matrix that makes the filter choose sensor values only updated is multiplied to measurement matrix. For the filter that has weak points on some criteria, filter fusion is suggested by using sigmoid function. Modified kalman filter is tested with practical case. A sigmoid function was designed for the test and the performance of the modified function is estimated with respect to conventional Kalman filter. Unscented Kalman filter is used to the base filter of the suggested filter because of its stability.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.19 no.1
• /
• pp.39-45
• /
• 2001

The design of highway in the future should be convenient using of a high-technology information, and it needs the design of alignment that is able to find the maximum vehicles inducement function fitting into Car Navigation System. Well then, the alignment of the existent highway needs to be analyzed with accuracy for improving design of existent highway, and it needs the design drawing of existent highway, and coordinates of the main point. This study gets data of the alignment of highway economically by Kinematic GPS surveying to analyze the alignment of existent highway, and horizontal alignment of highway is analyzed by this data. The result of study is included within range practical error, and alignment analysis can be known that there is practical.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.16 no.2
• /
• pp.235-242
• /
• 1998

This study aims to detect and to reduce the multipath errors which are main errors source in high precious surveying such as GPS-aided aerial triangulation and Car Navigation. which reference receivers being fixed, when kinematic receivers move continuously, multipath is performed using smoothed code measurement and pure code measurement in the network. Through this methods, 3D RMS errors are reduced into about 30% in the single differential code solution to the kinematic receiver. This is based on the fact that the network adjustment are performed at multiple reference receivers, but positioning is carried out by the single differential methods between a reference receiver and a kinematic receiver. So it was supposed that this methods reduced the correlation errors including the atmospheric errors using the nearest receivers and can be mixed with another methods.