• Journal of the Korean Society for Nondestructive Testing
• /
• v.24 no.4
• /
• pp.315-324
• /
• 2004

In eddy current testing(ECT), differential probes have been frequently used since they .an reduce the number of parameters that influence ECT signals. However, differential signal is actually the difference of the two coils' impedance so that signal prediction and interpretation are not easy, On the other hand, absolute coil signal is rather straightforward to predict and analyze. Therefore, combined use of the two types of signals would increase the test reliability. In this paper, absolute coil signals from Inconel plate and tubes are predicted by the finite element analysis and efforts of lift-off, fill-factor, conductivity, operating frequency, test specimen thickness, inner diameter defects, and outer diameter defects are investigated. As a result, various impedance plane diagrams are drawn and analyzed. Significant practical knowldege about absolute signals is accumulated and similar characteristics of the two types of signal could be understood. Finally, slope angle versus defect depth calibration corves are prepared for three different frequencies.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.24 no.3
• /
• pp.253-258
• /
• 2004

To get accurate information about the defect from the test signal, NDT engineers should have a good knowledge on forward problems. Such knowledge is usually obtained by a lot of testing experiences. Another why of obtaining such knowledge is to build a database containing lots of defect information and their corresponding signals. However, the archiving of raw test data would require a lot of storage space. In this paper, an economic way of storing signals is studied by using Fourier descriptors. Instead of saving raw signal data, Fourier descriptors are saved and the storage spare is reduced. Of course, the defect signal can be reconstructed from the stored descriptors. By using differential ECT signals produced by numerical modeling and experiment, the savings of 85% from the original signal and $57{\sim}65%$ from the filtered signal in the storage space were confirmed. The similarity of the reconstructed signal and the original signal was also demonstrated. This Fourier descriptor approach could contribute significantly in building differential signal databases.

• Proceedings of the KIEE Conference
• /
• 2005.07b
• /
• pp.1255-1257
• /
• 2005

본 논문에서는 튜브시트 내, 외부의 여러 다른 위치에서 확관이 이루어졌을 때 절대 및 차동 와전류신호를 유한요소 모델링으로 예측하고, 신호에서 자성 튜브시트로 인한 신호변화와 확관으로 인한 신호변화를 관찰하였으며, 이들에 미치는 주파수의 영향을 조사하였다. 그 결과, 절대 및 차동신호 모두 튜브시트의 위치 파악에는 저주파가 유리하고, 주파수가 높을수록 확관된 내경의 측정 및 확관 천이부의 파악이 용이하였으며, 절대신호가 차동신호에 비해 신호변화가 더 크고 지속적이어서, 확관 품질을 조사하기에 더 적합한 신호형태를 가지고 있음을 알 수 있었다.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.27 no.2
• /
• pp.89-96
• /
• 2007

The bobbin probe examination is basic and the important method among other ECT techniques for the steam generator tube integrity assesment that is practiced during each plant outage. The bobbin probe is one of the essential components which consist of the whole ECT examination system, and provides us a decisive data for the evaluation of tube integrity in compliance with acceptance criteria described in specific procedures. The selection of examination probe is especially important because the quality of acquired ECT data is determined by the probe design characteristics, such as geometry and operation frequency, and has enormous effects on examination results. In this study, An optimal differential bobbin probe is designed for the steam generator tube inspection in nuclear power plants(NPPs). Based on the test results for electrical and ECT signal characteristics, the prototype bobbin probe satisfies all the criteria.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.16 no.1
• /
• pp.29-33
• /
• 1996

The eddy current test(ECT) probe of differential encircling coil type was designed and fabricated, and the optimum condition of ECT was derived for the examination of the irradiated fuel rod. The correlation between ECT test frequency and phase & amplitude was derived by performing the test of the standard rig that includes inner notches, outer notches and through-holes. The defect of through-hole was predicted by ECT at the G33-N2 fuel rod irradiated in the Kori-1 nuclear power reactor. The metallographic examination on the G33-N2 fuel rod was Performed at the defect location predicted by ECT. The result of metallographic examination for the G33-N2 fuel rod was in good agreement with that of ECT. This proves that the evaluation for integrity of irradiated fuel rod by ECT is reliable.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.32 no.1
• /
• pp.64-70
• /
• 2012

Two kinds of eddy current probes are mainly used to perform the steam generator tube integrity assesment in NPPs. The first one is the bobbin probe using for inspection of volumetric defect like a fretting wear. The second one is the rotating probe using for inspection of non-volumetric defect like a crack. The eddy current probe is one of the essential components which consist of the whole eddy current examination system, and provides a decisive data for the tube integrity in accordance with acceptance criteria described in specific procedures. The design of ECT probe is especially important to improve examination results because the quality of acquired ECT data is depended on the probe design characteristics, such as coil geometry, electrical properties, operation frequency. In this study, it is analyzed that the coil winding number of differential bobbin probe affects the electrical properties of the probe. Eddy current bobbin probes for the steam generator tubes in NPPs are designed and fabricated according to the results. Experiment shows that the change in coil winding number has much effects on the optimum inspection frequency determined by the tube geometry and material. Therefore, the coil winding number in bobbin probe is very important in the probe design. In this study, a basis of the coil winding number for the eddy current bobbin probe design for steam generator tubes in NPPs is established.