• Proceedings of the Korea Water Resources Association Conference
• /
• 2012.05a
• /
• pp.904-904
• /
• 2012

강우-유출모형중 단기 홍수 사상 모형은 주로 집중형으로 하천유량 모의에 중점을 두어 왔고, 장기유출모형은 분포형으로 기저유출 모의에 중점을 두어 왔다. 단기 홍수사상 모형은 유역 전반에 걸친 수자원의 분포특성을 파악하기 힘들다는 단점이 있고, 장기유출모형은 단기 홍수사상을 분석하기 힘들다는 단점이 있다. 이와 같은 단점은 두 모형을 함께 이용하여 보완할 수 있다. 따라서 본 연구에는 단기 홍수사상모형인 HEC-HMS모형과 장기유출모형인 SWAT모형을 연동하기 위하여 두 모형에 공통으로 적용되는 매개변수 CN값을 적절히 구해 이용하여야 한다. 두 모형에서 CN값을 얻는 방법은 첫 번째, HEC-HMS모형의 홍수기 호우사상별 최적평균 CN값을 구하는 것이고, 두 번째, SWAT모형 내에서 적용되는 일별 CN값을 구하는 것이다. 그리고 두 모형의 매개변수를 이용하여 보정 3년(2002년~2004년), 검증 2년(2005년~2006년), 적용 3년(2007년~2009년)을 모델링하여 SWAT-HMS모형의 유출분석 신뢰성을 판단하였다. 보정 3년 결과로 선행 5일강우량 기준으로 150mm 이하이면 모의가능하고, 150mm 이상이면 과소 모의되는 SWAT모형의 단점을 알 수 있었다. 검증을 실시한 2년은 SWAT-HMS모형의 중요 매개변수인 CN값을 HEC-HMS모형의 CN값과 SWAT모형의 CN값을 적용한 결과를 비교하여 상관계수 0.90과 0.95를 얻었으며, SWAT-HMS모형에 적용되는 매개변수 CN값은 SWAT모형의 CN값을 사용할 경우 더욱 신뢰할 수 있음을 알았다. 적용 3년(2007년~2009년)은 SWAT모형의 CN값을 SWAT-HMS모형에 적용하여 유출분석을 하였으며, 관측치와 모의치의 상관계수 0.95라는 신뢰할 수 있는 결과를 얻었다. 그리고 관측치와 모의치의 첨두유량은 평균적으로 5% 이내의 차이로 정확한 모의결과를 얻을 수 있었다. 따라서 본 연구는 격자분포형 유출모형인 SWAT모형과 집중형 유출모형인 HEC-HMS모형을 두 모형에 공통으로 적용되는 매개변수 CN값을 이용하여 두 모형이 가지는 단점을 해소하여 보다 정확한 유출분석 결과를 얻을 수 있는 방법을 제시 하였다.

• Journal of Navigation and Port Research
• /
• v.38 no.1
• /
• pp.65-71
• /
• 2014

Gyeongbu and Namhae expressways in the country, are the major arterial highways which are connected with the Busan port in the north-south and east-west directions, respectively, and required to study the traffic characteristics about the hourly volume factors(K-factor) by concentrated midium-size and large-size cargo trucks of 20% or higher in expressways. We therefore attempted to predict the K-factor in expressways through the correlation analysis between K-factor and K-factor estimates on the basis of the short-term VDS data collected at the basic segments of the above major expressways. As a result, power model appeared to be appropriate in predicting K-factor by the K-factor estimate based on VDS data for 7 days with a high explanatory power and validity.

• Computational Structural Engineering
• /
• v.6 no.4
• /
• pp.89-98
• /
• 1993

As the construction of nuclear power plants are increased, nuclear wastes disposal has been faced as a serious problem. If nuclear wastes are to be buried in the underground stratum, thermo-mechanical behavior of stratum must be analyzed, because high temperature distribution has a significant effect on tunnel and surrounding stratum. In this study, in order to analyze the structural behavior of the underground which is subject to concentrated heat sources, a coupling method of nonlinear finite elements and linear boundary elements is proposed. The nonlinear finite elements (NFE) are applied in the vicinity of nuclear depository where thermo-mechanical stress is concentrated. The boundary elements are also used in infinite domain where linear behavior is expected. Using the similar method as for the problem in mechanical field, the coupled nonlinear finite element-boundary element (NFEBE) is developed. It is found that NFEBE method is more efficient than NFE which considers nonlinearity in the whole domain for the nuclear wastes depository that is expected to exhibit local nonlinearity behavior. The effect of coefficients of the rock mass such as Poisson's ratio, elastic modulus, thermal diffusivity and thermal expansion coefficient is investigated through the developed method. As a result, it is revealed that the displacements around tunnel are largely dependent on the thermal expansion coefficients.

• The Journal of the Korea Contents Association
• /
• v.15 no.5
• /
• pp.151-167
• /
• 2015

Korean movie maintain their market share from the highest 59.7% to the lowest 42.1% during the last ten years in Korea. However, with the multiplex and wide release strategy, the monopolies of four major distribution companies and three multiplex chain, the polarization of Korean movie's Box Office performance is deepening. With Gini-Index, concentration of film admission has been deepened in intensity from 0.53 in 2004 to 0.85 in 2014. Using Thomas Piketty's method, Movie attendance proportion of Highest 10% of the box office ranking for 2014 sharply increased to 71.2% from 30.28% in 2004 and the lowest 50% of box office ranking dropped from 11.03% in 2004 to 0.08% in 2014. Concentrations of the number of Screen, Screening, the seating Capacity have the same analogy with the polarization of film admission. However, concentration of seating share has maintained a modest increase from 0.22 in 2004 to 0.38 in 2014. This analysis shows that polarization of Korean movie box office performance is not the sole result of Natural selection of market but the result of the monopolies of distribution companies and Multiplex chains.

• The Journal of Engineering Geology
• /
• v.29 no.1
• /
• pp.23-35
• /
• 2019

Landslides occur due to heavy rainfall in the summer season. Some of water may infiltrate into the ground; it causes a high saturation condition capable of causing a landslide. Soil properties are crucial in estimating slope stability and debris flow occurrence. The main study areas are Gwanaksan, Suraksan and Bukhansan (Mountain) in Seoul. A total of 44 soil samples were taken from the study area; and a series of geotechnical tests were performed. Physical and mechanical properties were obtained and compared based on region. As a result, among well-graded soils, they are classified as a clayey sand. Coarse-grained and fine-grained contents are approximately 95% and 5%, respectively, with very low amount of clay content. Density, liquid limit and dry unit weight are ranged in $2.62{\sim}2.67g/cm^3$, 27.93~38.15% and $1.092{\sim}1.814g/cm^3$. Cohesion and internal friction angle are 4 kPa and $35^{\circ}$ regardless of mountain area. Coefficient of permeability is varied between $3.07{\times}10^{-3}{\sim}4.61{\times}10^{-2}cm/sec$; it means that it results in great seepage. Permeability is inversely proportional to the uniformity coefficient and is proportional to the effective particle size. In the formal case, there was a difference by mountain area, while in the latter, the tendency was almost similar.

• Korean Journal of Remote Sensing
• /
• v.17 no.1
• /
• pp.15-31
• /
• 2001

The relationship between GMS-5 IR1 brightness temperature (CTT:cloud top temperature) and AWS (automatic weather station) rainfall is investigated on a heavy rain event over the mid-western part of Korea for August 5-6, 1998. It is found that a temporal variability of the heavy rain can be described in detail y the time series of rain area and rain rates over the study area that are calculated from AWS accumulated rainfalls for 15 minutes. A time period of 0030-0430 LST 6 August 1998 is chosen in the time series as a heavy rain period which has relatively small rain area (20~25%) and very strong rain rates(6~9 mm/15 min.) with a good time continuity. In the heavy rain period, CTT of a point and AWS 15-minute rainfall beneath that point are compared. From the comparison, AWS rainfalls are shown to be not closely correlated with CTT. In the range of CTT lower than -5$0^{\circ}C$ where most AWS with rain are distributed, the probability of rain is at most about 30%. However, when the satellite images are shifted by 2~3 pixels southward and 3 pixels westward for the geometric correction of images, AWS rainfalls are shown to be statistically correlated with CTT (correlation coefficient:-0.46). Most AWS with rain are distributed in the much lower CTT range(lower than -58$^{\circ}C$), but there is still not much change in the rain probability. Even though a temporal change of CTT is taken into account, the rain probability amount to at most 50~55% in the same range.

• Asia-pacific Journal of Multimedia Services Convergent with Art, Humanities, and Sociology
• /
• v.7 no.2
• /
• pp.437-444
• /
• 2017

Stress concentrations around discontinuities, such as a hole in cross section of a structural member, have great importance because the most materials failure around the region may be occurred. Stress on the point applied by concentrated load reaches much larger value than the average stress in structural member. In this paper, stress analysis was performed for the plate with a partial through-hole to find the difference of the principal stress distribution. The difference between maximum principal stress and minimum principal stress in photoelasticity is equal to the value obtained by multiplying the isochromatic fringe order by the fringe constant of the material divided by the distance through which the light passes, that is, the thickness of the specimen. Since the difference of principal stress is proportional to the photoelastic fringe order, the distribution of the principal stress difference by the finite element analysis can be compared with the photoelasticity experimental result. ANSYS Workbench, that is the finite element software, is used to compute the differences of principal stresses at the specific points on the measured lines. The computation values obtained by ANSYS are compared with the experimental measurements by photoelasticity, and two results are comparable to each other. In addition, the stress concentration factor is obtained using the stress distribution analyzed from the variation of hole depth. Stress concentration factor is increasing, as the depth of hole increase.

• Applied Chemistry for Engineering
• /
• v.21 no.3
• /
• pp.258-264
• /
• 2010

Most of fluid systems, such as P&ID in ships, power plants, and chemical plants, consist of various components. The components such as bends, tees, sudden-expansions, sudden-contractions, and orifices contribute to overall pressure loss of the system. The local pressure losses across such components are determined using a pressure loss coefficient, k-factor, in lumped parameter models. In many engineering problems Idelchik's k-factor models have been used to estimate them. The present work compares the k-factor based on CFD calculation against Idelchik's model in order to confirm whether a commercial CFD package can be used for pressure loss coefficient estimation of complex geometries. The results show that RSM is the best appropriate for evaluating pressure loss coefficient. Commercial CFD package can be used as a tool evaluating k-factor even though the accuracy is influenced by a turbulence model.

• Journal of Korea Multimedia Society
• /
• v.1 no.2
• /
• pp.194-203
• /
• 1998

In this paper, a new DCT-VQ method is proposed which can solve the problems of VQ such as the degradation of edge and enormous calculations. VQ is carried in DCT domain but spatial domain in order to protect the degradation of edge. DCT makes high correlated image data decorrelated and the energy concentrated on a few coefficients. In DCT domain, the DC coefficient is quantized with 8 bits uniform scalar quantizer and the AC coefficients are divided to three regions and coded with vector qiantizer for considering edge components. For the decrease of the calculation and memory, the vectors for three region have small dimension of $1{\times}7$ and use the same codebook. Thus, the proposed method can fully express the edge components by considering AC coefficients in DCT domain and decrease the calculation and memory be reducing the dimension of vectors.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2010.05a
• /
• pp.362-366
• /
• 2010

하천 설계를 위한 다양한 수치모의 프로그램을 활용하여 홍수위, 침수심, 침수면적 등을 검토 분석하여 실시설계에 반영하고 사업을 추진하고 있으나, 실제 호우사상과 수치모의 모형에 대한 결과 분석은 매우 부족한 실정이다. 본 연구에서는 경기도 양평군 흑천 하류부를 대상으로 2006년 7월 집중호우 시 침수흔적도 및 HEC-GeoRAS에 의한 침수영향 비교 검토와 함께 하천 흐름의 주요 영향계수인 조도계수를 다양화하여 침수변화 양상 등에 대해 분석하였다. 모의 결과 흑천 하류부에 대한 침수영향은 침수흔적도와 서로 상이한 결과를 나타내고, 조도계수의 증가에 따라 침수면적은 증가 양상을 보이고 있다. 상기 결과를 볼 때 침수흔적도와 HEC-GeoRAS의 침수구역 비교 검토시에서는 피해당시의 하천환경에 대한 조사 및 피해원인에 대해 정밀 검토후 다양한 사례 연구 후 적용이 필요할 것으로 판단된다. 또한 침수모의 분석이 가능한 다양한 프로그램을 적용하여 향후 실제 침수흔적을 잘 반영할 수 있는 프로그램 개발과 적용시 착안 사항 등에 대한 검토도 병행할 필요가 있는 것으로 판단된다.