• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2007.10a
• /
• pp.340-343
• /
• 2007

OFDM (Orthogonal Frequency Division Multiplexing) system is robust to frequency selective fading and narrowband interference in high-speed data communications. However, an OFDM signal consists of a number of independently modulated subcarriers, which can give a large PAPR (peak-to-Average Power Ratio) when added up coherently. In this paper, we propose a new PAPR reduction method using Adaptive Sine Soft Clipping (ASS Clipping) to solve the PAPR problem. The proposed method reduce the PAPR and out-of-band spectrum by cutting down high frequency components. From computer simulation results, we analyze the PSD (Power Spectral Density) and BER (Bit Error Rate) performance as well as PAPR reduction performance when the ASS Clipping method is applied to OFDM system.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.34 no.4C
• /
• pp.403-413
• /
• 2009

We compare three predistortion methods to prevent signal distortion and spectral re-growth due to the high PAPR (peak-to-average ratio) of OFDM signal and the non-linearity of high-power amplifiers. The three predistortion methods are pth order inverse, indirect learning architecture and look up table. The pth order inverse and indirect learning architecture methods requires less memory and has a fast convergence because these methods use a polynomial model that has a small number of coefficients. Nevertheless the convergence is fast due to the small number of coefficients and the simple computation that excludes manipulation of complex numbers by separate compensation for the magnitude and phase. The look up table method is easy to implement due to simple computation but has the disadvantage that large memory is required. Computer simulation result reveals that indirect learning architecture shows the best performance though the gain is less than 1 dB at $BER\;=\;10^{-4}$ for 64-QAM. The three predistorters are adaptive to the amplifier aging and environmental changes, and can be selected to the requirements for implementation.

• Journal of Broadcast Engineering
• /
• v.4 no.2
• /
• pp.164-175
• /
• 1999

Based on the performance analyses for transmission channel and signal characteristics in digital satellite broadcasting system. the optimal design parameter values for system using QPSK modulation technique were proposed in this paper. The proper performance degradation were of 2.0dB for channel characteristics. O.4dB for transmission signal characteristics and 0.2dB for receiver characteristics. respectively. In this case. the design objectives for system parameters were within ${\pm}\;0.5dB$ for gain flatness in 27MHz bandwidth. and O.1nsec/MHz and $0.2sec/MHz^2$ for linear and parabolic group delay. respectively. Also. the optimal parameter values that provide the maximum availability were of OdB OBO for satellite transponder TWTA. and the optimal bandwidth for PLL circuit was of 40kHz with 0.707 damping factor. These analyses and design values can be available for high data rate transmission system via satellite.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.19 no.2
• /
• pp.118-128
• /
• 1999

There are many ultrasonic measurement methods that are used in nondestructive testing applications. Some typical applications include material property determination, microstructural characterization. and flaw detection. Ultrasonic parameters such as velocity and attenuation are most commonly required in these applications. The accuracy and repeatability of testing results are dependent on both the hardware used to generate and receive the ultrasonic waves and on the analysis software for calculating these parameters. In this study, five analysis algorithms were implemented on a computer for measuring wave speed in a pulse echo. immersion testing configuration. In velocity measurements comparisons were made between the overlap. cross-correlation. Fourier transform. Hilbert transform, wavelet transform algorithms. Velocity measurement was applied to an isotropic steel sample using the five analysis algorithms. Frequency-dependent phase/group velocity and attenuation were also measured using the Fourier transform and wavelet transform algorithms on a composite laminate containing voids.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.23 no.4
• /
• pp.932-939
• /
• 1998

In this paper, we analyze the performance of a multicode-CDMA system which have been proposed for the multimedia communications. The performance of a multicode-CDMA system, providing good spectrum efficiency as well as serving various bit rates, is analyzed with multipath, frequency selective, slowly fading Rayleigh channel. Also the proposed scheme adopting RAKE receiver with MRC(Maximal Ratio Combine) is advantageous to multipath channel. For a practical channel modeling, the JTC(Joint Technical Committee) recommended channel model(JTC(AIR) 23-065R6) is applied to simulation. The proposed schemehas serial-to-parallel convertor which splits input data stream of 2 Mits/s into 20 branches o 100 kbits/s. From the result of simulation, the case of RAKE receiver with 3 fingers to reduce the system complexity required the relatively large $E_{b}/N_O$ of 0 dB~1.5 dB, compared to the case of RAKE receiver with the number of path finger to keep the average error rate to be $1{\times}10^{-3}$ in channel A.

• 대한공업교육학회지
• /
• v.31 no.1
• /
• pp.185-199
• /
• 2006

In this paper, to detect lateral direction sound pressure fiber optic sensor using Fabry-Perot interferometeric sensor array was fabricated and experimented. This parallel sensor array composed of one light source and the light split into each sensor using directional coupler and to see the output signal the array system do not need any digital signal processor. As a lateral direction sound source arbitrary sound frequency of 100Hz, 200Hz, and 655Hz using by nondirectional speaker were applied to the array sensor which installed on $60cm{\times}60cm{\times}60cm$ latticed structure. The detected signals from the two sensors were analyzed in the time and frequency domains. It was confirmed that the suggested sensor array detected applied sound source well but there were a little amplitude differences in between the sensors. Because the sensor supported simply at both ends theoretical analysis was performed and its solution was suggested. To compare the theoretical and experimental results arbitrary sound frequency of 2kHz was applied to the sensor array. It shows that experimental results was good agreement with theoretical results.

• Geophysics and Geophysical Exploration
• /
• v.10 no.4
• /
• pp.299-307
• /
• 2007

Slowness time coherence (STC) technique has been applied to 3-receiver slim hole sonic log using 3 NX sized concrete model holes of different physical properties. We analyzed the effects of different source center frequencies on the wave forms, their amplitude spectra, and their STC results. We could determine the sonic velocity of each mode accurately by the application of STC method with the semblance projection and efficient selection of center frequency. Theoretical model and experimental model hole studies indicate that 4-receiver condition is the most ideal for STC in near surface slim hole sonic log. The result also indicates that favorable STC result can be obtained from three-receiver sonic log provided with the help of the first arrival picking method.

• Korean Journal of Optics and Photonics
• /
• v.25 no.5
• /
• pp.254-261
• /
• 2014

Two types of white light-emitting diodes (LEDs) with different phosphor structures were fabricated and compared in terms of their optical characteristics. Their spectroscopic properties were analyzed as a function of temperature, from room temperature to $80^{\circ}C$. The temperature dependence of the luminance and the color coordinates showed that the decrease in luminance and change in the color coordinates of the remote-phosphor type LED were much smaller compared to the conventional white LED. These improvements were attributed to the decrease in phosphor temperature, due to the distance between the LED chip and the phosphor layer, as well as to the reduced absorption by the LED chip of the light emitted from the phosphor layer.

• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.11 no.6
• /
• pp.104-110
• /
• 1997

In thes paper, the soung signals due to the collisions against the inside wall by conductint particles with in coaxial cylindrical electrodes, and the corresponding frequency spectrum are analyzed and discribed.Thesesound signals were detected and measured using ultrasonic and vibration sensors attached to the exterior of the GIS enclosure. In the case where a particls is bouncing about between these coaxoal electrodes, the sound signal was found to be more than 10[dB] greater than the background noise due to no particlel. Also, in the case where a particle collides and insulation breakdown caesed by the particle made it possible to determine the condition of the insulation inside the sealed GIS. Lastly, the relationship between the peak amplitude and RMS voltage of the measured signal, the diameter and length of the particle was analyzed. Using thes analysis, it is possible to confirm the size of particle.

• Journal of Convergence for Information Technology
• /
• v.11 no.9
• /
• pp.130-137
• /
• 2021

The characteristics of forced vibration by an external excitation force having a frequency were analyzed according to the amplitude and frequency of the excitation force. To obtain displacement, velocity, and acceleration, numerical analysis was performed to obtain the frequency response, and in particular, each FRF(Frequency Response Function) was analyzed to reveal the location of the system natural frequency and excitation frequency in the frequency domain. In the vibration model caused by external excitation, the natural frequency and distribution of the surrounding excitation mode in displacement, velocity and acceleration FRF. The FRF was also shown in the power spectrum and FRF of real and imaginary parts. The external excitation force was approximated with the excitation force of a sine wave by giving the amplitude and frequency, the mode generated by this excitation force could be distinguished. After numerical analysis by changing the equivalent mass, damping and stiffness, the forced vibration response characteristics by external excitation force were systematically analyzed.