• Journal of the Korean Geophysical Society
• /
• v.4 no.1
• /
• pp.21-33
• /
• 2001

Simultaneous inversion of first-arrivals of local earthquakes recorded by the Korea Meteorological Administration(KMA) seismograph network from 1991 to 1998 is made to derive 1D crustal velocity structure of the Korean peninsula. Twenty-nine events with 178 observations are used in the inversion. Average crustal P-wave velocity turns out to be about 6.3 km/sec, and crustal thickness and upper mantle P-wave velocity are estimated as 33 km and 7.9 km/sec, respectively. Results of inversion indicate the possibility of the low velocity layer in the lower crust. Joint inversion is applied to estimate hypocenters, station delays, and velocities simultaneously. Relative station corrections for 11 stations range from zero to about 1.2 sec. Analysis of the synthetic data shows that estimates of hypocenter locations and station corrections as well as averaged crustal structure are reliable for the given data set..

• Journal of the Korean earth science society
• /
• v.39 no.6
• /
• pp.593-599
• /
• 2018

The onset times of P- and S-waves are important information to have reliable earthquake locations, 1D or 3D subsurface velocity structures, and other related studies in seismology. As the number of seismic stations increases significantly in recent years, it becomes a formidable task for network operators to pick phase arrivals manually. This study used a simple method to estimate additional P- and S-wave arrival times for local earthquakes when a priori information (event location and time) is available using the Akaike Information Criterion (AIC). We applied the AIC program to the earthquake data recorded at the seismic station located in Gyeongsan (DAG2). The comparisons of automatically estimated phase arrival times with manually picked onset times showed that 95.1% and 93.7% of P-wave and S-wave arrival time estimations, respectively, are less than 0.1 second difference. The higher percentage of agreement presented the method which can be successfully applied to large data sets recorded by high-density seismic arrays.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.31 no.4A
• /
• pp.295-302
• /
• 2011

The setting time which is the important element for the determination of slip-up speed of Slip-Form system is the hardening time of early-age concrete when the in place concrete has minimum compressive strength before the concrete appears out of Slip-Form system. But it is very difficult to predict the setting time because it depends on not only the composition ratio of concrete but also various conditions of construction fields. Thus, the technique to estimate accurately and continuously the hardening time of early-age in place concrete during operating Slip-Form system is necessary to guarantee the safety of Slip-Form system and the maintenance of the shape of concrete. Ultrasonic wave-based nondestructive testing methods have the advantages which are accurate and continuous in estimating concrete compressive strength. Of such methods, the method using surface wave which propagates along the surface of material is effective for thick member such as a pylon. Thus, in this paper a study on the determination of slip-up speed for Slip-Form system using surface wave velocity is performed. The relation between the slip-up speed of Slip-Form system and the setting time is formulated, and the surface wave velocity is estimated from continuous wavelet transform of the numerical results for surface wave propagation. Finally, the accuracy of this method according to the distance between the wave source and receivers and the relation between the estimated surface wave velocity and the elastic modulus are investigated.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.32 no.5D
• /
• pp.483-492
• /
• 2012

The early setting time of concrete is an important factor determining the slip up velocity of the slip-form system. Accordingly, need is for a technique evaluating the early setting time in order to secure the safety of the slip-form system and the construction quality of concrete. This paper intends to estimate the early setting time by evaluating the setting degree of concrete using surface wave velocity so as to determine the slip up time of the slip-form system. Penetration resistance test and compressive strength test are performed first to clarify the relationship between the early setting time of concrete and the compressive strength. Then, compressive strength test and ultrasonic wave test are conducted to examine the relation between the compressive strength and the surface wave velocity. Continuous wavelet transform is adopted to measure the surface wave velocity. Numerical analysis is carried out to demonstrate the appropriateness of the application of continuous wavelet transform. Based on these results, the propagation velocity of the surface wave required for the slip up of slip-form system is suggested. Finally, a reduced model test of the slip-form system is conducted to verify the feasibility of the proposed surface wave velocity for the determination of th slip up velocity.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.40 no.1
• /
• pp.53-63
• /
• 2016

Wheel dynamometers are used to measure dynamic load that is conveyed from the road to a vehicle while driving. In this paper, two types of six-component wheel dynamometers utilizing shear deformation and bending deformation were designed and evaluated. Prior to designing the shear and bending type wheel dynamometers, the shear and bending deformation behaviors of the basic structure of the wheel dynamometer itself were analyzed using finite element analysis. Strain analysis was performed repeatedly in order to obtain a similar output sensing strain for each load component. The design was modified with a bridge circuit in order to minimize coupling strain. The results indicated that the shear type dynamometer was expected to obtain stable characteristics due to uniform strain distribution while the bending type dynamometer was expected to obtain high-quality sensitivity performance due to consistent output sensitivity.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.6
• /
• pp.771-780
• /
• 2010

This paper describes the design process of a six-component force/torque (F/T) sensor. The new six-component F/T sensor having leaf spring ends has been developed using a cross beam structure as the basic sensing element. Fundamental strain analysis of both ends fixed beam having a leaf spring structure is performed by finite element analysis. In order to obtain similar output sensing strains from the six component loads and minimize coupling strains, the optimal location of strain gages is determined and the strain gages are connected so that the bridge circuits with four strain gages would be balanced. Using leaf spring ends instead of rigid fixed ends, remarkable increment in output sensing strain can be achieved for two component forces. Several modifications in design result in a similar sensing strain of approximately $400\;{\mu}m/m$ for the six-component forces and moments, and a reduced coupling strain of $0\;{\mu}m/m$ between the forces and moments.

• The korean journal of orthodontics
• /
• v.30 no.2 s.79
• /
• pp.127-142
• /
• 2000

This study have been carried out to find out the mechnical effect of Multiloop Edgewise Arch Wire(MEAW) making use of the finite element method. The tip back bend of MEAW taken in this analysis is $5^{\circ},\;10{\circ}\;and\;15{\circ}$. In addition, Class II or up & down elastic is applied to find out stress distribution and their values in PDL. A adult male of normal occlusion was selected to create the models of teeth and PDL. And the model of MEAW was also created using commercial finite element code (ANSYS version 5.2). The MEAW is forcibly engaged with a class II or up & down elastic, to determine the initial stress generated in PDL. Comparing the compressive and tensile stress at each reference-planes, following results are obtained. 1. When a MEAW of $5^{\circ},\;10{\circ}\;15{\circ}$ tip back bend was engaged with Class II or up & down elastic, the distribution of compressive, tensile stress in entire PDL is similar in each case. 2. The values of compressive and tensile stress in PDL is higher in $15{\circ}$ tip back bend case than in $10{\circ}\;or\;15{\circ}$ tip back bend case. 3. In the distal PDL of 1st and 2nd molar, compressive stress appears. The compressive area is more wide and its values is higher in PDL of 2nd molar than those in 1st molar. The compressive area and its values become more wide and higher according to the increase of the tip back bend. 4. The values of compressive stress are comparatively smaIIer in PDL of molars than those in premolars. 5. Comparing class II and up & down elastic case, tensile stress values in anterior teeth PDL are smaller md their distribution is more wide in up & down elastic case than class If elastic case. On another hand, there is no difference in distribution and stress values in PDL of posterior teeth between two cases. 6. Comparing the tensile area in PDL of anterior teeth, tensile stress values are maximum in PDL of canine.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.9
• /
• pp.412-419
• /
• 2019

Negative space in the discipline of art defines the space around and between the subject of an image. The use of negative space is an element of artistic composition, since it is occasionally used to artistic effect as the "real" subject of an image. In painting, it is a technique that negatively touches the background of an object to be expressed, so that it gives a feeling of unique texture and silhouette by touching unnecessary parts while leaving necessary parts. As in art, negative space in a design can also be useful to identify an image of infeasible design ranges with a straightforward view. Similarity between two disciplines leads to the introduction of the negative space concept for design space exploration. A rough design space exploration using statistics and visual analytics may support more efficient decision-making, and can provide meaningful insights into the direction of early-phase system design. For this, the approach guarantees dynamic interactions between visualized information and human cognitive systems. Visual analytics is useful to summarize complex and large-scale data. It is useful for identifying feasible design spaces, as well as for avoiding infeasible spaces or highly risky spaces. This paper investigates the possible use of the negative space concept by using an application example.

• Journal of Korea Society of Industrial Information Systems
• /
• v.25 no.6
• /
• pp.25-32
• /
• 2020

The seed, the most basic component, is an important factor in increasing production and efficiency in agriculture. Seeds with superior genes can be expected to improve agricultural productivity, crop survival, and reproduction. Currently, however, screening of superior seeds depends mostly on manual work, which requires a lot of time and manpower. In this paper, we propose a system that can extract the characteristics of seed phenotypes by using computer image processing technology, so that even a small number of people and a short period of time are needed to extract the characteristics of seeds. The proposed system detects individual seeds from images containing large quantities of seeds, and extracts and stores various characteristics such as representative colors, area, perimeter and roundness for each individual seed. Due to the regularity of input images, the accuracy of individual seed extraction in the proposed system is 99.12% for soybean seeds and 99.76% for rice seeds. The extracted data will be used as basic data for various data analyses that reflect the opinions of experts in the future, and will be used as basic data to determine the expressive nature of each seed.