• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.1
• /
• pp.97-107
• /
• 2015

An analytical model was developed to estimate the viscous and squeeze-film damping ratios of heat exchanger tubes subjected to a two-phase cross-flow. Damping information is required to analyze the flow-induced vibration problem for heat exchange tubes. In heat exchange tubes, the most important energy dissipation mechanisms are related to the dynamic interaction between structures such as the tube and support and the liquid. The present model was formulated considering the added mass coefficient, based on an approximate model by Sim (1997). An approximate analytical method was developed to estimate the hydrodynamic forces acting on an oscillating inner cylinder with a concentric annulus. The forces, including the damping force, were calculated using two models developed for relatively high and low oscillatory Reynolds numbers, respectively. The equivalent diameters for the tube bundles and tube support, and the penetration depth, are important parameters to calculate the viscous damping force acting on tube bundles and the squeeze-film damping forces on the tube support, respectively. To calculate the void fraction of a two-phase flow, a homogeneous model was used. To verify the present model, the analytical results were compared to the results given by existing theories. It was found that the present model was applicable to estimate the viscous damping ratio and squeeze-film damping ratio.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.1795-1800
• /
• 2003

An experimental study was carried out to investigate near-wake characteristics of an elliptic airfoil oscillating in pitch. The airfoil was sinusoidally pitched about the half chord point between $-5^{\circ}C$ and $+25^{\circ}C$ angles of attack at the freestream velocities of 3.4 and 23.1 m/s The corresponding Reynolds numbers based on the chord length were $3.3{\times}10^4$ and $2.2{\times}10^5$, respectively. A hot-wire anemometer was used to measure the near-wake flow variable at the reduced frequency of 0.1. Ensemble-averaged velocity and turbulence intensity profile were presented to examine the near-wake characteristics depending on the Reynolds number. The axial velocity deficit in the near-wake region tend to decrease with the increase in the Reynolds number a found in many stationary airfoil test . Turbulence intensity in the near-wake region have a tendency to decrease with the increase in the Reynolds number during the pitch-up motion, whereas it shows different feature during the pitch-down motion either the laminar boundary layer or turbulent boundary layer separation.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1993.12a
• /
• pp.39-50
• /
• 1993

최근 회전계의 고속화, 소형화 및 정숙운전에 대한 요구가 엄격해짐에 따라 볼베어링을 저어널베어링으로 대체하는 흐름이 증가하고 있으나, 저어널베어링의 기본 구조상 운전시 여러 종류의 진동모드가 발생되며 이에 따라 엄밀한 설계가 요구된다. 이러한 요구에 따라 본 연구에서는 불안정성을 억제할 수 있는 것으로 알려진 빗살무늬 저어널베어링을 대상으로 하여 보다 정확한 설계를 위한 수치해석 프로그램을 개발하였다. 빗살무늬저어널베어링의 해석법으로는 간극의 비선형성을 단순화 시키기 위하여 무한홈을 가정한 협곡이론을 시초로 하여 최근에는 컴류터 계산속도의 발달로 실제 형상에 대해 해석한 직접계산법 등이 알려져 있다. 직접계산법은 협곡이론에 의한 계산법에 비해 많은 시간이 걸리는 단점이 있으나, 베어링이 소형화되어 실제 많은 홈을 가공하기 힘들거나 홈이 원호형으로서 직각홈으로 가정하기가 곤란한 요소에서는 협곡이론을 적용하는데 무리가 있을 것으로 사료된다. 따라서 본 연구에서는 직접계산법을 채택하여 소형 베어링 모델에 대한 부하특성을 수치해석하고, 이를 협곡이론과의 비교를 통하여 그 차이점을 검토하였다. 이를 위해 압축성을 고려한 레이놀즈 방정식에 대한 베어링 주위의 압력분포를 계산하는 프로그램을 제작하였으며, 주어진 설계조건하에서 빗살무늬 형상을 결정하는 피라미터들의 최적값을 산출하고, 아울러 플레인저어널베어링과의 비교를 통하여 설계조건에 따른 빗살무늬저어널베어링의 기존 불베어리의 대체 가능성을 평가하였다.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.12 no.2
• /
• pp.150-160
• /
• 2000

Turbulent natural convective flow and heat transfer in a square enclosure with horizontal partition are investigated numerically. The enclosure is composed of a lower hot and a upper cold horizontal walls and adiabatic vertical walls. Partitions carried with the upward, downward, and both control plates are attached perpendicularly to the one of the vertical insulated walls, respectively. The low Reynolds number $k-\varepsilon$ model is adopted to calculate the turbulent thermal convection. The governing equations are solved by using the finite element method with Galerkin method. The computations have been carried out by varying the length of partition, the position of control plates, and the Rayleigh number based on the temperature difference between two horizontal walls and the enclosure height for water(Pr=4.95). When the control plates are attached at the edge of partition, the stability of oscillating flow grows wrose with the increase of Rayleigh number and the partition length. The heat transfer rate has been reducer than that of no control plate due to the restraint of control plates with the increase of Rayleigh number.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2012.05a
• /
• pp.566-570
• /
• 2012

본 연구에서는 비선형 k-$\varepsilon$ 모형을 이용하여 직사각형 개수로에서 평균흐름과 난류구조를 모의하였다. 표준 k-$\varepsilon$ 난류모형은 난류의 등방성을 가정하여 국부적 평형상태에서 계산하기 때문에 유선에 따른 레이놀즈 응력의 변형이 큰 경우나 이방성이 강한 경우 이를 계산하지 못한다. 이를 보완하기 위하여 제시된 것이 비선형 k-$\varepsilon$ 난류모형이다. 본 연구에서는 표준 k-$\varepsilon$ 모형과 비선형 k-$\varepsilon$ 모형에 의한 모의결과를 비교하였다. 난류모형을 검증하기 위하여 직사각형 개수로에 흐름을 완전 발달된 등류로 가정하여 해석하였다. 지배방정식을 해석하기 위해 Patankar와 Spalding (1972)이 제시한 SIMPLER 알고리즘을 사용하였고 유한체적법을 이용하여 이산화하고 엇갈린 격자체계를 사용하여 계산에서 발생하는 과도한 진동을 줄였다. 또한 차분기법은 Patankar (1980)가 제시한 Power-law 기법을 채택하였으며 경계조건으로 2층 벽법칙 모형과 Hossain과 Rodi (1993)의 모형을 이용하였다. 두 모형의 적용성을 검증하기 위하여 실측자료를 이용하여 비교하였고 그 결과 비선형 k-$\varepsilon$ 모형이 표준 k-$\varepsilon$ 모형에 비해 좀 더 실측지에 가깝게 모의하는 것을 볼 수 있었다.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.7 no.2
• /
• pp.21-27
• /
• 2003

In general, simple fluid added mass method is used for the seismic and vibration analysis of the immersed structure to consider the fluid-structure interaction effect. Actually, the structural response of the immersed structure can be affected by both the fluid added mass and damping caused by the fluid viscosity. These variables appeared as a consistent matrix form with the coupling terms. In this paper, finite element formula for the inviscid fluid case and viscous fluid case are derived from the linearized Navier Stoke's equations. Using the finite element program developed in this paper, the analyses of fluid added mass and damping for the hexagon core structure of the liquid metal reactor are carried out to investigate the effect of fluid viscosity with variation of the fluid gap and Reynolds number. From the analysis results, it is verified that the viscosity significantly affects the fluid added mass and damping as the fluid gap size decrease. From the analysis results of eccentricity effect on the fluid added mass and damping of the concentric cylinders, the fluid added mass increase as the eccentricity increases, however the fluid damping increases only when the eccentricity is very severe.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.46 no.1
• /
• pp.59-67
• /
• 2018

In this paper, the test facility for coaxial propellers at low Reynolds developed and validated by measured data. The test equipment was designed to measure the hovering performance of propellers according to distances between the upper/lower propellers. Thrust, torque, rotational speed, vibration, and amperage of upper and lower propellers can be measured separately. The data acquisition system was built to collect signals of sensors, and LabVIEW software was used to control the motor and collect the signal. The hover performance tests of single propellers were preceded for the facility validation, and then the performance values of coaxial propellers were measured according to distances and diameter differences between the upper/lower propellers. The results showed that the high efficiency is achieved at 20%~30% distance between the upper propeller and lower one. The configuration that the upper propeller has shorter diameter than the lower one has the highest efficiency than other configuration.

• Journal of Ocean Engineering and Technology
• /
• v.29 no.1
• /
• pp.9-15
• /
• 2015

We investigated the Reynolds number effects on the flow over a twisted offshore structure in the range of 3×10³≤ Re ≤ 1 × 10⁴. To analyze the effect of the twisted surface treatment, a large eddy simulation (LES) with a dynamic subgrid model was employed. A simulation of the cylindrical structure was also carried out to compare the results with those of the twisted offshore structure. As Re increased, the mean drag and lift coefficient of the twisted offshore structure increased with the same tendency as those of the cylindrical structure. However, the increases in the mean drag and lift coefficient of the twisted offshore structure were much smaller than those of the cylindrical structure. Furthermore, elongated shear layer and suppressed vortex shedding from the twisted offshore structure occurred compared to those of the cylindrical cylinder, resulting in a drag reduction and suppression of the vortex-induced vibration (VIV). In particular, the twisted offshore structure achieved a significant reduction of over 96% in VIV compared with that of the cylindrical structure, regardless of increasing Re. As a result, we concluded that the twisted offshore structure effectively controlled the flow structures with reductions in the drag and VIV compared with the cylindrical structure, irrespective of increasing Re.