• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2013.10a
• /
• pp.103-108
• /
• 2013

This paper describes basic properties tests and non-rotating dynamic test for rotor blade, flexbeam, and torque tube of which bearingless rotor in helicopter consists. A basic properties test are bending and twist test to find the flap stiffness, lag stiffness, and twist stiffness of specimens. The purpose of dynamic test is to find natural frequencies and modes in non-rotating state. The test results are used to update the analysis model. The updated analysis results using rotorcraft comprehensive code match the tests quite well. The updated model input based on the tests will be utilized to analysis the conditions of rotating whirl tower test before the whirl test and will be compared with the whirl tower test results.

• Journal of Korea Society of Industrial Information Systems
• /
• v.4 no.1
• /
• pp.58-62
• /
• 1999

This paper shows that is possible to identify the system's input-output dynamics exactly in the presence of unknown periodic disturbances for the Active Engine Mount Control Application .The disturbance frequencies and waveforms can be completely unknown and arbitrary. Only measurements of a control excitation signal and the disturbance-contaminated response are used for identification. Examples are given to illustrate the method, including the identification and vibration control of active engine mount for automobile.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2010.10a
• /
• pp.374-375
• /
• 2010

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.777-777
• /
• 2007

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.951-952
• /
• 2011

발전소에 설치된 대용량 발전기는 고정자 권선을 지지하기 위해 축 방향으로 삽입된 슬롯 Wedge의 지지압력이 느슨해지면 절연파괴와 같은 각종 사고가 발생할 수 있다. 이를 예방하기 위해 주기적으로 Wedge 조임 상태를 점검하고 있으나 그동안 작업자의 손가락 감각으로 평가하던 방법을 가속도 진동 센서를 이용하여 주파수 스펙트럼을 분석함으로써 발전기 고정자 Wedge 조임 상태를 객관적으로 판정할 수 있도록 방법을 고안하였다.

• Proceedings of the Korean Institute of Industrial Safety Conference
• /
• 1997.11a
• /
• pp.251-257
• /
• 1997

압전 바이몰프형 엑츄에이터에 진동판을 부착한 압전팬은 압전 바이몰프의 굴곡진동을 이용한 요동식 팬으로, 코일식 모타 팬에 비해 구조 및 풍량의 조절이 간단하고 미소량의 풍량 (1m/s)을 일으킬 수 있다. 또한 전자적인 잡음이 발생치 않는다. 수명이 재래 전자팬은5,000-10,000시간인데 비해 약 25,000시간으로 길며 압전체이기 때문에 대응한 전자석 로타리 팬 전력의 1/15mw이하의 저 소비전력을 갖는등의 잇점을 가지고 있다. (중략)

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11b
• /
• pp.767-770
• /
• 2002

Reduction of the propagation noise generated during pass-by of KTX by noise barrier was measured and analysed for the two kinds of top-shaped noise reduction devices; one as a plywood board and the other as a PVC pipe were placed periodically. The height and length of reference noise barrier are 2.4 m and 50 m, respectively. The noise reduction with and without noise reduction devices was investigated.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11b
• /
• pp.950-955
• /
• 2002

ISO 140-11 specifies a method for measuring the acoustic properties of floor coverings from the view-point of reducing impact sound transmission. This test method is limited to the specification of procedures for the physical measurement of sound originating from an artificial impact source under laboratory conditions. In this study, ISO 140-11 was reviewed to applicable to domestic floor coverings installed on lightweight floors.

• Proceedings of the KSME Conference
• /
• 2001.11a
• /
• pp.539-543
• /
• 2001

Almost all rotating machinery has bearings. Bearing is one of the most important part of rotating machinery. Vibration of rotating machinery depend on its bearing conditions. Bearing conditions are followings ; oil gap, bearing type, bearing temperature, bearing oil condition. Especially, bearing oil condition influences on rotating machinery vibration directly. In this paper we have discussed the abnormal vibration of turbine due to oil condition. oil whip problem was occured in the certain power plant. and we had sloved this problem through the control of operating values and alignment.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11a
• /
• pp.392.2-392
• /
• 2002

ISO 140-11 specifies a method for measuring the acoustic properties of floor coverings from the view-point of reducing impact sound transmission. This test method is limited to the specification of procedures for the Physical measurement of sound originating from an artificial impact source under laboratory conditions. In this study, ISO 140-11 was reviewed to applicable to domestic floor coverings installed on lightweight floors.