• Journal of Korean Tunnelling and Underground Space Association
• /
• v.20 no.2
• /
• pp.433-452
• /
• 2018

The shield tunneling method can minimize surface settlements by preventing the deformation of tunnel face and tunnel intrados due to tunnel excavation. For this purpose, it is very important to control the operating conditions of shield TBM. The face pressure and backfill pressure for tail void grouting should be the most important and immediate measure not only to restrain surface settlement, but also to influence the effective stress and pore water pressure around the circumstance of tunnel during excavation. The reaction of the ground to the application of face pressure and backfill pressure relies on the stiffness and permeability of ground. Especially, the reaction of saturated clayey ground formations, which shows the time-dependent deformation, is different from the permeable ground. Hence, in this paper it was investigated how the TBM operating conditions, ground stiffness, and permeability impact on the surface settlement of saturated clayey ground. For this purpose, a series of parametric studies were carried out by means of the stress-pore water pressure coupled FE analysis. The results show that the settlement of soft clayey ground is divided into the immediate settlement and consolidation settlement. Especially, the consolidation settlement depends on the ground stiffness and permeability. In addition, the existence of critical face pressure and backfill pressure was identified. The face pressure and backfill pressure above the critical value may cause an unexpected increase in the ground settlement.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.1
• /
• pp.25-33
• /
• 2018

Renewable energy has been of interests in the area of modern alternative fuels. Biogas is produced in waste landfill sites through anaerobic digestion processes, including hydrolysis, acidogenesis, organic acid fermentation (acetogenesis), and methane fermentation (methanogenesis). High contents of fine dust and moisture limited its utilization for direct combustion, town gas and vehicle fuel. Thus, this study proposed a new design for a cooling device using a centrifugal cyclone for simultaneous removal of fine dust and moisture as a pretreatment in the purification processes. A heat exchanger and an ID fan, which are installed inside and outside of the cyclone, in order to cool the humid gas below the freezing point and form a foggy mist. Such an atmosphere enhanced to capture fine dust as recirculating the cold mist flow. The water removal rate was 80.8% at a relative humidity of 95%, and the particle removal efficiency was 98.3% for $2.5{\mu}m$. Simultaneous removal efficiency was 70.8% and 99.6% for particle and moisture respectively.

• Microbiology and Biotechnology Letters
• /
• v.34 no.2
• /
• pp.109-114
• /
• 2006

Yam has been recognized as healthy food due to its various biological activities, such as anti-obesity, antimicrobial, anticancer and immuno-stimulation activities, and its consumption has been increased during last decades. In this study, to investigate low-temperature, long-term storage of yam and to develop processed yam products, yam-putrefactive psychrotrophic bacteria were isolated from rotted yam and identified based on BBL identification system, fatty acid analysis in cell membrane and 16S rDNA sequence analysis. The putrefaction activity of isolated thirteen bacteria was evaluated using yam-slices (NaOCl-treated, autoclaved yam and without treatment), and YAM-10 and YAM-12 were identified as major psychrotrophic putrefactive bacteria. Both YAM-10 (Pseudomonas cepacia) and YAM-12 (Pseudomonas rhodesiae) bacteria grew well at 4$\sim$12$^{\circ}C$ and showed strong activity of polymer degrading enzymes, especially amylase, carboxy methyl cellulase and xylanase, at 20$^{\circ}C$. But they failed to grow at acidic pH (<5) or alkaline pH (>10). Our results suggested that the control of psychrotrophic Pseudomonas sp. by pH change and inhibition of polymer degrading enzymes, such as amy-lase, are necessary to long-term storage of yam.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.12
• /
• pp.446-452
• /
• 2016

Recently, heat resistant super alloys (which are wear-resistant, corrosion-resistant, and heat-resistant), have been used as the basic structural material in offshore and petrochemical plants. On the other hand, making valves from very expensive, high heat-resistant alloys increases the production cost and decreases its market competitiveness. To solve these problems, the technique of overlaying only those that flow on the fluid has been used as an effective method. Nevertheless, because the former technique of overlaying the ball is performed manually, it takes too much time and perfect welding is difficult to perform. To solve this problem, this study developed a robot automation system that can make uniformly overlay welding of the ball for ball-valves. The system consists of a 6-axis welding robot with a welding torch and additional 2 axes for the rotation of positioner, the controller, and a robot path OLP (Off-Line Programming). The CAD drawing data was entered in the Off-line program to obtain the robot teaching point and drive source. Overlay welding paths were implemented using Matlab. Through an automated overlaying system that implemented the OLP, the productivity rose 2.58 times, as the amount of time required for work decreased from 88 hours to 41 hours.

• KIPS Transactions on Computer and Communication Systems
• /
• v.6 no.6
• /
• pp.271-280
• /
• 2017

In this paper, we propose a new safety system composed of wearable devices, driver's seat belt, and integrating controllers. The wearable device and driver's seat belt capture driver's biological information, while the integrating controller analyzes captured signal to alarm the driver or directly control the car appropriately according to the status of the driver. Previous studies regarding driver's safety from driver's seat, steering wheel, or facial camera to capture driver's physiological signal and facial information had difficulties in gathering accurate and continuous signals because the sensors required the upright posture of the driver. Utilizing wearable sensors, however, our proposed system can obtain continuous and highly accurate signals compared to the previous researches. Our advanced wearable apparatus features a sensor that measures the heart rate, skin conductivity, and skin temperature and applies filters to eliminate the noise generated by the automobile. Moreover, the acceleration sensor and the gyro sensor in our wearable device enable the reduction of the measurement errors. Based on the collected bio-signals, the criteria for identifying the driver's condition were presented. The accredited certification body has verified that the devices has the accuracy of the level of medical care. The laboratory test and the real automobile test demonstrate that our proposed system is good for the measurement of the driver's condition.

• Nuclear Engineering and Technology
• /
• v.13 no.4
• /
• pp.264-276
• /
• 1981

A simulation procedure which can represent time-dependent nuclear characteristics of TRIGA Mark-III reactor is developed. CITATION, a multi-group diffusion-depletion program, has been utilized as calculational tool. The group structure employed in this study consists of 7 groups: -3-fast and 4-thermal-which is conventionally utilized in TRIGA type reactor analysis. Three-dimensional nuclear characteristics are synthesized by combining results from two-dimensional plane calculation and two-dimensional cylinder calculation, since direct three-dimensional approach is not yet possible. An effort ia made to develope a method which can extract effective zone and group dependent bucklings by neutron diffusion theory rather than conventional zone and/or group independent Ducklings by neutron transport theory, since neutron leakage is quite high for small core such as research reactors. It is turned out that the method developed in this study gives satisfactory results. The calculation is performed under assumptions that all control rods are fully withdrawn, that no samples are inserted in the irradiation holes and that the core is located in the center of the reactor pool. Burnup-dependent variation of core excess reactivity, time dependent change of Xe-135 poisoning and reactivity worth of rotary specimen rack are calculated and compared with operation records. Neutron flux and power distribution as well as neutron spectrum in each irradiation .facility are presented.

• Proceedings of the Korean Society of Postharvest Science and Technology of Agricultural Products Conference
• /
• 2003.04a
• /
• pp.126-127
• /
• 2003

원예산물의 밀도나 비중은 내부성분, 숙도, 내부붕괴(internal breakdown)와 같은 생리장해에 큰 영향을 받기 때문에, 밀도를 측정함으로써 내부품질에 대한 간접적인 판정이 가능하다고 보고되고 있다. 이 연구는 수박의 밀도와 당도와의 상관관계를 구명하고자 수행하였으며, 이를 위해 밀도의 실시간 계측시스템을 개발하였다. 현재 농산물의 밀도를 어느 정도 측정 정밀도를 유지하면서도 신속하게 측정할 수 있는 방법은 부력법(platform scale method)이다. 이 방법은 일정 크기의 용기에 물을 가득 채운 후 대상물을 담가 배제된 물의 무게를 측정하여 밀도를 환산한다. 그러나 매번 측정할 때마다 물을 보충하고, 물을 계량해야하는 등 전처리과정이 복잡하고, 1회 측정하는데 3~5분 정도가 소요되는 단점이 있고, 또한 인력 측정시 반복간 오차가 클 것으로 예상된다. 따라서 이 연구에서는 이 같은 계측상의 번거로움을 해소하고 동시에 신속하고 반복간 측정정밀도를 높일 수 있도록 수박 밀도 실시간 계측시스템을 설계 제작하였다. 시스템은 투명아크릴 수조($\Phi$400$\times$500), 로드셀, 프레임, 채반, 전기모터, 제어장치 및 컴퓨터로 구성하였다. 밀도 계측은 인장형 로드셀(CAS SB-20L, Max. 20kg)을 사용하여 대기중에서와 수박을 완전히 물에 잠기도록 한 후 무게를 각각 측정하여 밀도를 환산하였다. 밀도 계측시스템에 이용한 AD변환기의 분해능은 12bit이고, 수박의 무게 측정범위를 4~10kg로 가정할 때 20kg 로드셀의 1 digit(1bit)로 발생되는 오차는 0.09~0.24%FS 이었고, 따라서 이 시스템의 밀도 해상도는 0.001g/㎤이하였다. 시스템 평가를 위해 탄력이 좋은 고무풍선에 수박 크기 정도로 물을 채워 고정채반에 넣고 밀도를 측정한 결과 1.002g/㎤을 나타냈다. 즉 물의 이론밀도인 1g/㎤에 근접한 값을 보여 정확한 밀도 계측이 가능한 것으로 판단되었다. 또한 밀도 계측시스템의 측정 반복간 정밀도를 파악하기 위해 수박 6개를 임으로 선정하여 3반복 측정 시험한 결과, 측정표준편차가 0.001~0.004g/㎤로 해상도보다는 다소 높았으나 대체로 양호한 결과를 나타냈다. 수박 35개를 이용하여 개발 계측시스템과 사람이 직접 부력법으로 밀도를 측정 비교한 결과, 계측시스템에 의해 측정된 수박 밀도가 사람이 측정했을 때 보다 낮게 측정되었다. 수박의 외관인자(무게, 길이, 직경, 체적), 밀도와 당도의 상관관계 구명시험을 위해 원예연구소 시험포장에서 재배된 삼복꿀수박 총 74개를 공시재료로 하였고, 시험은 출수일별로 10~14개씩 수확하여 외관인자, 밀도, 당도를 각각 측정하고, 이들 인자들간의 상관관계를 구명하였다. 외관인자들간에는 높은 상관관계를 보였으나, 외관인자들과 밀도, 외관인자들과 당도, 밀도와 당도와는 매우 낮은 상관관계를 나타냈다.

• Food Science and Preservation
• /
• v.18 no.2
• /
• pp.256-265
• /
• 2011

To investigate the effect of a solar salt on Kimchi fermentation, Chinese cabbages were brined with four-years aged solar salt (FS), one-year aged solar salt (OS), and purified salt (PS). The Kimchi was fermented at $7^{\circ}C$ for 33 days. The changes in pH and acidity of the Kimch brined with PS was slower than those of Kimchis brined with FS and OS. In the Kimchis with FS and OS, lactic acid bacteria (LAB) counts increased from 7.10~7.22 log CFU/mL at 0 day to 9.26~9.42 log CFU/mL at 12 days, after which counts slightly decreased to 8.04~8.75 log CFU/mL by 33 days of fermentation. The LAB counts of the kimchi with PS slowly increased from 7.24 log CFU/mL at 0 day to 8.99 log CFU/mL at 27 days, after then which counts sharply decreased to 7.92 log CFU/mL by 33 days of fermentation. Yellowness (b) color values of the kimchi with PS (59.10) was higher than the Kimchi with FS (53.68) and the Kimchi with OS (53.77). Hardness of the Kimchi with FS was more firm than the other Kimchis after 33 days storage. Sensory evaluation of the Kimchi with FS showed higher score than that of the other Kimchis.

• Proceedings of the Korean Association of Geographic Inforamtion Studies Conference
• /
• 2008.10a
• /
• pp.65-72
• /
• 2008

Mobile Collaboration is an enabling technology that makes users share information between mobile devices and various Mobile P2P platforms have been designed and implemented for it. There are, however, few research papers on application of SIP protocol to spatial data sharing on mobile devices. In this paper, SIP based real time sharing framework is proposed to compose a mobile P2P platform on which spatial data can be trans(erred. A new protocol based on WKT and WKB is defined to send and receive spatial objects with SIP MESSAGE method. Base maps such as digital maps and parcel maps can be provided by a map server that is integrated with SIP server after a new SIP session established and client agents are registered. The framework proposed based onSIP enables users to transfer spatial data such as maps and satellite images directly between mobile devices during VoIP based voice call and therefore, mobile applications can be applied in various domains such asforest management and national defense.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.48 no.3
• /
• pp.41-49
• /
• 2011

In this paper, we propose an open protocol to be employed between a smart meter concentrator and a metering data collection server, and also evaluate its performance. Legacy concentrators performs the connection establishment and data gathering operations with DLMS/COSEM protocol standards. However, we note that there are no standardized protocols between the concentrator and the collection server, which inevitably conduces each commercial smart metering system to have its own proprietary protocol. In order to solve this problem, we propose an open protocol - Smart Meter Concentrator Control Protocol(SMCCP) by extending the existing standard protocol(DLMS/COSEM). The SMCCP can provide the proxy mode to enable efficient transmission between the concentrator and the data collection server. It also can support the relay mode to enable a direct communication between the data collection server and each far end smart meter. We also implement an emulator system and a protocol analyzer to provide its operation. In addition, we evaluate the session holding time and the link usage ratio in both relay and proxy modes with OMNET++ simulator.