• 한국자동차공학회논문집
• /
• 제22권3호
• /
• pp.105-113
• /
• 2014

Spray and combustion process with waste cooking oil (WCO) biodiesel and commercial diesel were analyzed in an optically-accessible single-cylinder compression ignition diesel engine equipped with a high pressure common-rail injection system. Direct imaging method was applied to investigate spray and combustion characteristics. From the mie-scattering results, it was verified that WCO biodiesel had a longer injection delay compared to diesel. Spray tip penetration length of WCO biodiesel was longer and spray angle was narrower than those of diesel due to poor atomization characteristics. In terms of combustion, WCO biodiesel showed later start of combustion, while flame was vanished more rapidly. Analysis of flame luminosity showed that WCO biodiesel combustion had lower intensity and lasted for shorter duration.

• 한국분무공학회지
• /
• 제10권4호
• /
• pp.47-53
• /
• 2005

This paper presents the effects of ambient pressure on atomization characteristics of high-Pressure injector in a direct injection gasoline engine both experimentally and numerically. The atomization characteristics such as mean droplet size, mean velocity, and velocity distribution were measured by phase Doppler particle analyzer. The spray development, spray penetration, and global spray structure were visualized using a shadowgraph technique. In order to investigate the atomization process numerically, the LISA-DDB hybrid model was utilized. This breakup model assumes that the primary breakup occurs when the amplitude of the unstable waves is equal to the radius of the ligament of liquid sheet near the nozzle and the droplet deformation induces the secondary breakup. The results provide the effect of ambient pressure on the macroscopic and microscopic behaviors such as spray development, spray penetration, mean droplet size, and mean velocity distribution. It is also revealed that the accuracy of prediction of LISA-DDB hybrid model is pretty good in terms of spray developing process, spray tip penetration, and SMD distribution.

• 한국자동차공학회논문집
• /
• 제7권7호
• /
• pp.42-53
• /
• 1999

Two dimensional flame temperature and KL value distribution from the luminous flame containing soot in a DI diesel engine were measured by the tow-color method using tow different wavelengths of the flame image. The combustion chamber of a DI diesel engine was visualized by elongating the piston and cylinder and the flame in the combustion chamber was photographed on a nega-color film using a high speed camera. In this study, color CCD camera was used to digitize the three color density of the film exposed to the flame and standard lamp . The accuracy of the measuring method depends on the calibration line of film made from a high temperature standard tungsten lamp. The formation and oxidization of soot in the diesel engine were studied by observing measured time history of KL factor and flame temperature . Also , effects of various shapes of combustion chamber and fuel injection on flame temperature. Also, effects of various shapes of combustion chamber and fuel injection on flame temperature and KL value distribution were examined.

• 한국정보통신학회:학술대회논문집
• /
• 한국정보통신학회 2014년도 춘계학술대회
• /
• pp.919-920
• /
• 2014

따개비(barnacle)는 선저부에 붙어서 번식하며 딱딱한 석회질 껍데기로 덮여있다. 이로 인하여 선박의 속도를 저하시키고 도료기능을 상실시키는 주요인이 된다. 이를 제거하기 위해 작업자가 직접 액체를 분사하고 브러쉬로 세척해야 한다는 불편함과 위험에 노출되기 때문에 선박작업용 로봇이나 기계들이 많이 개발되고 있다. 현재 연구 중이거나 개발이 완료된 것 중에는 영구자석 또는 전자석 휠을 사용하거나 공압을 이용하여 수직벽면에서 작업을 한다. 특히 공압 방식을 많이 사용하였는데 수직벽면에 로봇이 밀착될 만큼 강한 공압이 필요하게 되기 때문에 부가적인 장치가 많이 필요하다. 본 논문에서는 부가적인 장치를 최소화하고 효과적인 동작을 하기위해 전자석 방식을 선택 하였으며 간편하게 선박의 수직벽면을 작업할 수 있는 전자석 방식의 4륜 로봇을 개발하고자 한다. 선박의 수직벽면 작업용 4륜구동 로봇을 전자석을 이용하여 수직벽면에 부착할 수 있도록 설계하였으며 자력의 세기와 방향을 제어하여 로봇이 선박의 수직면에 밀착되어 자유롭게 이동이 가능하도록 개발 하고자 한다.

• 한국산업융합학회 논문집
• /
• 제26권4_2호
• /
• pp.649-656
• /
• 2023

Recently, global warming has become severe, and regulation is established for carbon savings each field. its regulation is applied to various fields using IC engine such as automobile, ship, agricultural machine. Therefore engine block applied Common Rail Direct Injection(CRDI) technology, that carry out thermal-structure analysis to examine design. The thermal load about 900℃ by explosion was applied in cylinder. And pressure about 9 MPa(90 Bar) was applied to structure analysis. As a result, it was the highest at 185.99℃ at the top of cylinder. Static-structure analysis applied thermal load, that was shown maximum equivalent stress at 142.59 Mpa and Maximum principal stress 145.03 MPa, Minimum principal stress -149 MPa. When compare analysis results to material property, it design is safety structurally.

• 대한기계학회논문집B
• /
• 제26권9호
• /
• pp.1276-1283
• /
• 2002

Recently, HSDI (High Speed Direct Injection) diesel engine has been spotlighted as a next generation engine because it has a good potential for high thermal efficiency and fuel economy. This study was carried out to investigate the in-cylinder flow characteristics generated in a 4-valve small diesel cylinder head with a tangential and helical intake port. The flow characteristics such as coefficient of flow rate(Cf), swirl ratio (Rs), and mass flow rate (ms) were measured in the steady flow test rig using the impulse swirl meter and the analysis of in-cylinder flow field was conducted by experiment using the PIV and calculation using the commercial CFD code. As the results from steady flow test indicate, the mass flow rate of the cylinder head with a short distance between the two intake ports is increased over 13% than that of the other head. However, the non-dimensional swirl ratio is decreased approximately 15%. From in-cylinder flow characteristics obtained by PIV and CFD calculation, we found that the swirl center was eccentric from the cylinder center and the velocity distribution became uniform near the TDC. In addition, the results of the calculation are good agreement with the experimental results.

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 2017년도 춘계공동학술대회
• /
• pp.60-60
• /
• 2017

화석연료의 고갈과 환경오염이 문제시 되면서 친환경 에너지개발에 대한 연구가 진행되고 있다. 그중 바이오디젤은 동,식물성유지 및 폐식용유를 이용하여 생산이 가능할뿐더러 농용엔진에 특별한 개조 없이 사용가능하다. 또한 바이오디젤 자체에 산소를 함유하고 있어 이산화탄소 저감에 효율적이다. 바이오 디젤에 관한 많은 연구가 수행되었으며, 기존의 연구는 단일유지의 폐식용유를 사용하여 바이오디젤을 생산하는 연구가 진행되었다. 하지만 가정에서 배출되는 식물성 폐식용유의 경우 여러 가지가 혼합되어 배출되고 있어, 혼합폐식용유지의 바이오디젤 특성평가가 필요하다. 따라서 본 연구에서는 폐식물성유지(폐대두유, 폐카놀라유, 폐해바라기유)를 중량비(1:4, 1:1.5 1:0.66, 1:0.25)로 혼합하여 바이오디젤을 생산하고, 생산한 바이오디젤을 농용기관에 이용하여 농용기관의 출력특성 및 배기배출물특성 평가를 실시하였다. 실험에 사용된 농용기관은 배기량이 673cc인 직접분사식 디젤기관(ND10DE, Daedong, Korea)이며, 엔진성능평가를 위해 토크는 토크센서(YDL-704s, Setech, Korea)를 사용하였다. 배기배출물 평가는 배기가스분석기(HG-550, Airlex, Germany)를 이용하여 이산화탄소, 질소산화물을의 배출량을 측정하였다. 폐식용유를 이용하여 생산한 바이오디젤과 경유의 기관성능을 비교한 결과 토크와 축출력의 경우 BD의 혼합량이 증가할수록 줄어들었다. 토크는 혼합된 유지에 따라 상용운전범위인 1500rpm~2400rpm에서 평균 대두와 카놀라유를 혼합하여 생산한 BD10은 7.2%, BD20은 12.1% 감소하였고, 대두와 해바라기유를 혼합하여 생산한 BD10은 11.3% BD20은 16.3% 감소하였다. 또한 해바라기와 카놀라유를 혼합하여 생산한 BD10은 8.3%, BD20은 14.6% 감소하였다. 이는 BD의 발열량이 경유에 비해 낮아 토크가 감소한 것으로 판단된다. 또한 배기배출물 평가의 경우 질소산화물은 BD의 함랑이 증가함에 따라 경유에 비해 배출량이 증가하는 경향을 보였고, 이산화탄소는 저감되는 것으로 나타났다. 이는 바이오디젤이 함산소연료이므로, 연료내의 산소로 인해 완전연소를 촉진시켜 이산화탄소를 저감시키고 질소산화물은 증가된 것으로 판단된다.

• 대한기계학회논문집B
• /
• 제36권7호
• /
• pp.737-744
• /
• 2012

차량에 의한 대기오염을 실제 주행 조건에서 시간과 공간에 구애받지 않고 실시간으로 측정하기 위하여 이동형 배출가스 측정장치(MEL)가 제작되었다. 미니밴 차량에 CO, NOx, $CO_2$와 같은 배출가스 측정 장비와 입자의 수농도 및 입경별 개수농도 분포 측정을 위한 FMPS, CPC가 탑재되었다. 차량 전단에 장착되는 흡입 샘플링 포트를 사용하여 여러 종류의 차량 추적 실험을 수행하였다. 본 연구에서는 MEL의 상세 사양 및 이를 이용하여 디젤 및 가솔린 연료를 사용하는 승용차량들을 추적 실험한 결과를 나타내었다. 디젤 차량에서 배출되는 입자의 수농도는 가솔린 차량에서 배출되는 입자의 수농도보다 높았으며 다량의 극미세입자를 포함하고 있었다. 하지만, 직접분사식 가솔린 차량은 DPF가 장착된 디젤 차량에 비하여 50 nm 이상의 입경 영역에서 입자의 농도가 높은 경향을 보였다.

• 대한기계학회논문집B
• /
• 제26권5호
• /
• pp.724-732
• /
• 2002

Although the demands for diesel engine is increased, our world is faced with very serious problems related to the air pollution due to the exhaust emissions of the diesel engine. In this study, the potential possibility of oxygenated fuel such as Methyl tertiary butyl ether (MTBE) was investigated for the sake of exhausted smoke reduction from diesel engine. MTBE has been used as a fuel additive blended into unleaded gasoline to improve octane number, but the study of application for diesel engine was incomplete. Because MTBE includes oxygen content approximately 18%, it is a kind of oxygenated fuel that the smoke emission of MTBE is reduced remarkably compared with commercial diesel fuel, that is, it can supply oxygen component sufficiently at high load and speed in diesel engine. But, the NOx emission of MTBE blended fuel is increased compared with commercial diesel fuel. And. it was tried to analyze not only total hydrocarbon but individual hydrocarbon components from $C_1$to $C_{6}$ in exhaust gas using gas chromatography to seek the reason for remarkable reduction of smoke emission. The results of this study show three conclusions. 1. The smoke omission of the MTBE blended fuel is lower than that of the diesel fuel at all experimental region in direct injection diesel engine. 2. Individual hydrocarbons(C$_1$~ $C_{6}$) as well as total hydrocarbon of oxygenated fuel are reduced remarkably compared with diesel fuel. 3. Smoke emission from diesel engines was strongly depended on oxygen content in fuel regardless of operating condition.

• 해양환경안전학회:학술대회논문집
• /
• 해양환경안전학회 2007년도 추계학술발표회
• /
• pp.133-137
• /
• 2007

An experimental study is conducted to evaluate and compare the use of BiodieseDI Fuel supplements at blend ratio of 10/90(BDF10) and 20/80(BDF20), in four stroke, direct injection diesel engine located at the authors' laboratory. especially this Biodiesel is produced from Rape oil at the authors' laboratory. The tests are conducted using each of the above fuel blends, in the engine working at a speed of 1800rpm and at a various loads. In each test, specific fuel consumption, exhaust emissions such as nitrogen oxides(NOx), carbon monoxide(CO) and Soot are measured. The results of investigation at various operating conditions are as follows (1) Specific fuel consumption is increased average 1.52%, maximum 1.84% at load 25% in case of BDF10, and average 1.98%, maximum 2.80% at load 25% in case of BDF20. (2) CO emission is decreased average 5.14%, maximum 6.09% at load 0% in case of BDF10, and average 7.75%, maximum 9.13% at load 0% in case of BDF 20. (3) NOx emission is increased average 2.97%, maximum 3.74% at load 0% in case of BDF10, and average 3.84%, maximum 4.67% at load 0% in case of BDF20. (4) Soot emission is decreased average 9.36%, maximum 10.85% at load 75% in case of BDF10, and average 11.99%, maximum 13.95% at load 75% in case of BDF20.