• Korean Journal of Remote Sensing
• /
• v.32 no.2
• /
• pp.185-194
• /
• 2016

The effect of artificial changes in geographical features on local wind was analyzed at the construction site of bridge and fill-up bank in the southern part of Haui-do. Geographic Information System (GIS) data and Computational Fluid Dynamics (CFD) model were used in this study. Three-dimensional numerical topography based on the GIS data for the target area was constructed for the surface boundary input data of the CFD model. The wind observations at an Automatic Weather Station (AWS) located in Haui-do were used to set-up the model inflows. The seasonal simulations were conducted. The differences in surface wind speed between after and before artificial changes in geographical features were analyzed. The surface wind speed decreases 5 to 20% at the south-western part and below 2% of the spatial average for salt field. There was also marked the effect of artificial changes in geographical features on local wind in the westerly wind case for the target area.

• Proceedings of the Korea Contents Association Conference
• /
• 2007.11a
• /
• pp.942-946
• /
• 2007

The new gravity field combination models are expected to improve the knowledge of the Earth's global gravity field. This study evaluates six global gravity field models derived from gravimetry and altimetry surface data in a comparison with ground truth in South Korea. For calculating a more accurate estimate of the geoid heights from the height anomalies, the terrain corrections due to the terrain masses over geoid have considered, the model for the topographic correction is a spherical harmonic expansion of the ETOPO2 DTM model. Geoid heights obtained from GPS and levelling in land area of South Korea are compared with those from the EGMs. The results show that EIGEN-CG03C EGM and EIGEN-GL04C EGM displayed the nearest results to GPS/leveling, and also confirmed the importance of terrain correction for geoid height in case of the uneven topography.

• Journal of Korean Society for Geospatial Information Science
• /
• v.19 no.4
• /
• pp.101-108
• /
• 2011

Construction of the Jangbogo antarctic station was planned, and it requires detailed information on topography of the area around the station. The purpose of this research is to generate the topographic map to construct the Jangbogo antarctic station using the satellite image. To do this, surveying and pre-test of equipment were conducted. In addition, for sensor modeling of the GeoEye-1 satellite image, RPC-bias correction was done, and it showed that at least two control points are required. In generating the map, a 1/2,500 scale was deemed suitable in consideration of resolution of the image and the fact that supplementary topographic surveying would be impossible. In order to provide detailed information on the topography around the Jangbogo station, the digital elevation model based on image matching was created, and compared with GPS-RTK data, accuracy of vertical location about 0.6m was exhibited.

• Proceedings of the KSR Conference
• /
• 2009.05a
• /
• pp.1003-1009
• /
• 2009

The Spatial Image contents of Geomorphology 3-D environment is focused by the requirement and importance in the fields such as, national land development plan, telecommunication facility management, railway construction, general construction engineering, Ubiquitous city development, safety and disaster prevention engineering. The currently used DEM system using contour lines, which embodies geographic information based on the 2-D digital maps and facility information has limitation in implementation in reproducing the 3-D spatial city. Moreover, this method often neglects the altitude of the rail way infrastructure which has narrow width and long length. This As the results, We confirmed the solutions of varieties application for railway facilities management using 3-D spatial image contents and database design. Also, I suggested that U-city using railway modeling about matching methods of high density elevation value using 3-D aerial photo with laser data are best approach for detail stereo modeling and simulation.

• Journal of Korean Society for Geospatial Information Science
• /
• v.14 no.3 s.37
• /
• pp.55-62
• /
• 2006

The purpose of the current research is to evaluate the possibility of landslides by using geo-spatial information system. Geological information has been summarized and stability analysis for infinite slopes has been conducted based on the force equilibrium. In addition, the analysis of landslides was performed based on probabilistic approach by using probabilistic variables which can include uncertainty of input parameters. For the purpose of testifing the applicability of the analysis method actual geological data from a construction site was obtained, thereby performing both a preliminary analysis for a large area and detailed analysis for a better result. As a result of the current analysis several issues such as the possibility of development of landslides, detailed analysis of where landslides are most likely to be developed were analysed by using two concepts of safety and index of failure probability.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.20 no.2
• /
• pp.111-118
• /
• 2002

These days, surveying instruments are developing rapidly and the precision is improving continuously. The building of three dimensional terrains of high precision are possible and the calculation of the areas or the volumes have high precision due to the development of the technique of the spatial information system using computer. But actually, in construction site they calculate two-dimensional area using the traditional method, plate table surveying, planimeter, and then get three-dimensional area through multiplying two-dimensional area by the slope correction factor. In this study, we show the defect and inefficiency of the calculation of area by the traditional methods and survey the area with Electric Distance Measurement and GPS instrument. With this data, we made the three dimensional terrain model and calculated two-dimensional area, three-dimensional area. After that, we compared areas that calculated by algorithm of triangulated irregular network and analysis of grid method with standard area that calculated by the traditional method. Finally, this paper suggested more effective and precious method in calculating three-dimensional area.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.27 no.6
• /
• pp.723-731
• /
• 2009

Recently, it has been strangely increasing rainfall and rainfall meter by global warming. so flood damage is being increase. It has happened there are so many damaged by influence by backwater of dam. However, the alleviative solutions of flood damages are focused on the lower river basin where the density of population is higher than upper river basin. This research proceeds based on design and build 3D topography model and reflects the topographical factors of upper river basin. It also simulated the circumstances of flooding by investigation of factors of outflow, hence, as a result, we would find out the vulnerable area for flooding and scale of damages effectively. This research suggests the solution and method of flooding for vulnerable area of the flooding to reduce the damages by predicting flooding. Thus, the suggestion may support to make a decision efficiently to prevent the damage of flooding.

• Korean Journal of Remote Sensing
• /
• v.35 no.5_1
• /
• pp.715-726
• /
• 2019

With the increasing prevalence of high-resolution satellite images, the need for technology to generate accurate 3D information from the satellite images is emphasized. In order to create a digital terrain model (DTM) that is widely used in applications such as change detection and object extraction, it is necessary to extract trees, buildings, etc. that exist in the digital surface model (DSM) and estimate the height of the ground. This paper presents a method for automatically generating DTM from DSM extracted from KOMPSAT-3A stereo images. The technique was developed to detect the non-ground area and estimate the height value of the ground by using the previously constructed low-resolution topographic data. The average vertical accuracy of DTMs generated in the four experimental sites with various topographical characteristics, such as mountainous terrain, densely built area, flat topography, and complex terrain was about 5.8 meters. The proposed technique would be useful to produce high-quality DTMs that represent precise features of the bare-earth's surface.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2018.05a
• /
• pp.7-7
• /
• 2018

1차원 하수관로 해석 모형과 2차원 지표면 유출 해석 모형을 연계한 1D-2D 결합 도시침수 모델은 도시지역의 유출 현상과 침수 모의에 널리 이용되고 있다. 그러나 도시 지역의 복잡한 지형이 지표면 유출 흐름에 미치는 영향을 보다 자세히 파악하기 위해서는 보다 높은 해상도의 지형자료를 활용한 모의가 필요하다. 본 연구에서는 도시침수 해석을 위한 1D-2D 결합 하이브리드(Hybrid) 병렬화 코드(H12)를 개발하여 넓은 도시 유역에 대해서 고해상도 지형자료를 활용한 모의가 유역단위로 가능하도록 하였다. H12는 Open Multi-Processing(OpenMP)와 Message Passing Interface(MPI) 병렬 계산을 동시에 수행하여 매우 넓은 지역에 대해서도 도로의 형태를 확인 할 수 있는 수준의 고해상도 침수 해석 모의가 가능하다. 또한 도시지역의 복잡한 지형을 자세히 재현하고 계산의 효율을 높이기 위하여 격자세분화 기법이 적용되었다. H12의 적용성을 평가하기 위하여 미국 텍사스 알링턴 지역의 Johnson Creek 유역(${\sim}40km^2$)유역에 대한 시범 모의를 수행하였으며 도시유역의 지형을 표현하기 위하여 1m 해상도의 LiDAR자료를 사용하여 침수발생시 보다 자세한 유출수의 흐름을 해석할 수 있도록 하였다. 모의 결과 하이브리드 병렬 계산은 순차적 계산에 비하여 최고 79배 이상 빠른 계산속도 효율 향상을 보여주었으며, OpenMP나 MPI를 단독으로 사용하는 것에 비하여 더욱 효율적인 계산속도 효율 향상을 보여주었다.

• Korean Journal of Agricultural and Forest Meteorology
• /
• v.15 no.1
• /
• pp.17-25
• /
• 2013

In this paper we interpreted the changes in wind field over complex mountainous terrains. The results of our study can be applied for predicting the direction of fire spread and for establishing strategies for fire prevention. The study area is bounded by $12{\times}12$ km domains of the Samcheok's long-term ecological research (LTER) site located in the east coast, in which a large-fire had occurred from 7 to 13 April 2000. Because of the area's complex topography, we compared the result of the Weather Research and Forecasting (WRF) mesoscale model with those observed by four automated weather stations. The WRF simulation overestimated the wind speed by 5 to 8 m/s (~200%) in comparison with those from four automated weather stations. The wind directions observed by the AWSs were from various directions whereas those from WRF model were mostly west wind at all stations. Overall, the simulations by the WRF mesoscale models were not appropriate for the estimation of microscale wind fields over complex mountainous areas. To overcome such inadequacy of reproducing the wind fields, we employed the ENVI-met model over Samcheok's LTER site. In order to test the model's sensitivity with the terrain effects, experimental simulations were conducted with various initial conditions. The simulation results of the ENVI-met model showed a reasonable agreement in wind speeds (about 70% accuracy) with those of the four AWSs. Also, that the variations in wind directions agreed reasonably well with changes in terrain effect. We concluded that the ENVI-met model is more appropriate in representing the microscale wind field over complex mountain terrains, which is required to predict fire spread and to establish strategies for forest fire prevention.