• Proceedings of the Korean Association of Geographic Inforamtion Studies Conference
• /
• 2003.04a
• /
• pp.354-362
• /
• 2003

위성영상으로부터 위치자료가 포함된 지리 및 지형정보를 얻기 위해서는 영상획득순간의 센서 위치 및 자세와 지상좌표간의 관계를 해석하여야 한다. 위성영상에 대한 수학적 모형화를 위해서 먼저 입체영상에서 지상기준점(Ground Control Point: GCP)을 선정하고, 선정된 지상기준점에 대한 지상좌표 및 대상영상에 대한 영상좌표 관측작업을 수행한다. 본 연구에서는 지상기준점 데이터베이스에 포함된 정보들을 이용하여 관측대상 입체영상 3차원 모형화에 필요한 지상기준점의 영상좌표를 자동으로 추출할 수 있는 기법을 개발하였다. 관측정밀도는 수작업으로 관측한 값과 자동계산된 영상좌표의 결과를 비교 분석하여 평가하였으며, SPOT위성영상의 3차원 모형화에 적용하여 정확도를 평가하므로써 유사한 해상도의영상을 활용하는 3차원 모형화 과정에서 지상기준점의 영상좌표 관측을 자동화 할 수 있음을 입증하였다.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.21 no.4
• /
• pp.301-308
• /
• 2003

This study describes the methodology that improves the accuracy of the 3D object-space data extracted from IKONOS satellite images by improving the accuracy of a RPC(Rational Polynomial Coefficient) model. For this purpose, we developed the algorithm to adjust a RPC model, and could improve the accuracy of a RPC model with this algorithm and geographically well-distributed GCPs(Ground Control Points). Furthermore, when a RPC model was adjusted with this algorithm, the effects of geographic distribution and the number of GCPs on the accuracy of the adjusted RPC model was tested. The results showed that the accuracy of the adjusted RPC model is affected more by the distribution of GCPs than by the number of GCPs. On the basis of this result, the algorithm using pseudo_GCPs was developed to improve the accuracy of a RPC model in case the distribution of GCPs was poor and the number of GCPs was not enough to adjust the RPC model. So, even if poorly distributed GCPs were used, the geographically adjusted RPC model could be obtained by using pseudo_GCPs. The less the pseudo_GCPs were used -that is, GCPs were more weighted than pseudo_GCPs in the observation matrix-, the more accurate the adjusted RPC model could be obtained, Finally, to test the validity of these algorithms developed in this study, we extracted 3D object-space coordinates using RPC models adjusted with these algorithms and a stereo pair of IKONOS satellite images, and tested the accuracy of these. The results showed that 3D object-space coordinates extracted from the adjusted RPC models was more accurate than those extracted from original RPC models. This result proves the effectiveness of the algorithms developed in this study.

• Proceedings of the Korean Association of Geographic Inforamtion Studies Conference
• /
• 2003.04a
• /
• pp.115-120
• /
• 2003

일반적으로 광학위성은 궤도가 부정확하여 지상기준점(GCP)을 이용하여 궤도를 보정하는 작업을 수행한 후 수치 표고모형 자료(DEM)를 추출한다. 지상기준점은 실제 측량이나 지형도로부터 얻게 되지만, 이러한 작업이 불가능한 경우에는 광학영상으로부터 수치 표고 모형 자료를 추출할 수 없다. 본 연구에서는 수-수십 cm의 위성 궤도 정확도를 지니는 ESA ERS영상과 약 1Km의 해상도를 지니는 GTOPO-30 DEM을 이용하여 지상기준점을 추출 방법에 대해 연구하였다. 연구지역인 대전 주변에 대하여 지상기준점을 추출한 결과 경도 -0.348초, 위도 0.293초의 오차를 나타내었다. 또한 추출된 지상기준점을 이용하여 한 쌍의 SPOT 위성영상으로부터 DEM을 추출이 가능하였으며, 레이더 interferometry 기술을 이용한 지형고도 추출 및 변화 탐지에도 활용될 수 있음을 확인하였다.

• Journal of Korean Society for Geospatial Information Science
• /
• v.16 no.4
• /
• pp.25-31
• /
• 2008

As we choose ground control points for aerial triangulation, we have a lot of problems in a mountain, a costal area, a desert, the foreshore etc because they don't have clear topography for control points and it spends a lot of cost and occurs problems of accuracy. In this study, we compare and analyze between ground control points from LiDAR intensity, digital map with ground control points from the field survey as doing AT each. As the result, the average error was ${\pm}1.02m$ from using LiDAR intensity, ${\pm}1.13m$ from using digital map. this result can present the control points from LiDAR intensity is 0.11m better than from digital map.

• Proceedings of the Korean Association of Geographic Inforamtion Studies Conference
• /
• 1999.12a
• /
• pp.52-58
• /
• 1999

본 연구에서는 국내의 항공사진측량에서 적용되지 않고 있는 광속조정 Program을 구현하였다. 또한, 구현된 프로그램을 이용하여 과천지역에 대한 측량자료를 처리하였다. GPS를 이용하여 결정한 카메라 노출중심 위치를 이용하여 광속조정에 적용한 결과는 지상기준점수가 감소하여도 정확도는 완만하게 저하되었으나, 지상기준점만을 이용하여 광속조정에 적용한 결과는 지상기준점수가 감소함에 따라 정확도는 급격하게 저하되었다. GPS를 이용하여 결정한 카메라 노출중심 위치를 광속조정에 적용한 결과 블록 가장자리에 배치한 4개의 지상기준점 만으로 공공측량에 적합한 결과를 얻을 수 있었다. 본 연구를 통하여 GPS로 결정한 카메라의 노출중심위치를 항공삼각측량에 적용할 경우 필요한 지상기준점수를 축소함으로써, 비용을 절감할 수 있을 것으로 판단된다.

• Proceedings of the Korean Association of Geographic Inforamtion Studies Conference
• /
• 2003.04a
• /
• pp.531-536
• /
• 2003

In this paper, a camera modeling method that utilizes ephemeris data and imaging geometry is presented. The proposed method constructs a mathematical model only with parameters that are contained in the leader file and does not require any ground control points for model construction. Control points are only needed to eliminate geolocation error of the model that is originated from errors in the parameters that are used in model construction. With few (one or two) of control points, RMS error of less than pixel size can be obtained and control points are not necessarily uniformly distributed over the entire scene. This advantage is crucial in large project and will enable to reduce project cost dramatically.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.28 no.1
• /
• pp.153-160
• /
• 2010

It is necessary to determine accurate 3-dimensional coordinates of the building corner points that could be control or check points in order to verify the accuracy of 3D digital maps in the near future. The usual process of obtaining the coordinates of the building corner points is to set up the ground control points with a GPS and then to practice terrestrial survey such as distance or angle measurements. However, since an error in the ground control points can be propagated through the terrestrial survey into the final coordinates of the buildings, accurately should be considered as much as possible. The actual effect of the GPS-derived ground control point error on the estimates of the unknowns through the terrestrial survey is mathematically analyzed, and the simulation data is tested numerically. The error of the ground control points is tested in the cases of 1-4 cm for the horizontal components and 2-8 cm for the vertical component. The vertical component error is assigned twice the horizontal ones because of the characteristics of the GPS survey. The distance measurement is assumed for convenience and the precision of the estimated coordinates of the building corner points is almost linearly increased according to the errors of the ground control points. In addition, the final estimates themselves can vary by the simulated random errors depending on the precision of the survey instrument, but the precision of the estimates is almost independent of survey accuracy.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.21 no.1
• /
• pp.61-69
• /
• 2003

There is various kinds cause that influence to created DEM and orthoimage using stereo satellite images. Specialty, research about effect that GCP number gives to accuracy of DEM, orthoimage and modeling may have to be gone ahead. Therefore, this research increases GCP number by 5 to 30 and created each modeling, DEM and orthoimage using SPOT panchromatic images that resolution is 10m by digital image processing method. Accuracy assessment did by orthoimage using 20 check point. As a result, GCP number between 10∼30 modeling RMSE is 1 pixel low appear. Horizontal·vertical error that use orthoimage looked tendency that decrease GCP number increases, and confirmed by the most economical in GCP number 10∼15. Also, analyze correlation of GCP number and orthoimage position accuracy and presented improvement plan and research task hereafter.

• Journal of Korean Society for Geospatial Information Science
• /
• v.11 no.2 s.25
• /
• pp.29-37
• /
• 2003

An approach is described for automatic measuring of GCP's image coordinates from SPOT imagery and focused on the fulfillment an automatic orientation of satellite images. For the orientation of a stereopair of digital images, firstly, GCP(Ground Control Point) should be selected and then the work for measuring of image coordinates correspond to GCPs is required. In this study, we propose the method for extracting the GCP's image coordinates automatically using an image patch for control points and auxiliary points matching. For the evaluation of measurement accuracy, a comparison between points those are extracted manually and automatically by a proposed method have made. Finally, we shows the feasibility of automatic image coordinates measurment by applying in stereo modeling for SPOT images.

• Korean Journal of Remote Sensing
• /
• v.24 no.4
• /
• pp.299-307
• /
• 2008

It is possible to extract qualified ground control points (GCPs) from SAR data itself without published maps. TerraSAR-X data that are one of highest spatial resolution among civilian SAR systems is now available. In this study, a sophisticated method for GCP extraction from TerraSAR-X data was tested and the quality of the extracted GCPs was evaluated. Mean values of the distance errors were 0.11m and -3.96 m with standard deviations of 6.52 m and 5.11 m in easting and northing, respectively. The result is one of the best among GCPs possibly extracted from any civilian remote sensing systems. The extracted GCPs were used for geo-rectification of IKONOS image. The method used in this study can be applied to KOMPSAT-5 for geo-rectification of high-resolution optic images acquired by KOMPSAT-2 or follow-up missions.