• 대한치과보철학회:학술대회논문집
• /
• 대한치과보철학회 2000년도 추계학술대회
• /
• pp.23-24
• /
• 2000

• Journal of Dental Rehabilitation and Applied Science
• /
• 제39권4호
• /
• pp.229-236
• /
• 2023

Maxillary bone defects may follow surgical treatment of benign and malignant tumors, trauma, and infection. Palatal defects often lead to problems with swallowing and pronunciation from the leakage of air into the nasal cavity and sinus. Obturators have been commonly used to solve these problems, but long-term use of the device may cause irritation of the oral mucosa or damage to the abutment teeth. Utilizing implants in the edentulous area for the fabrication of the obturators has gained attention. This case report describes a patient, who had undergone partial resection of the maxilla due to adenocarcinoma, in need of a new obturator after losing abutment teeth after long-term use of the previous obturator. Implants were placed in strategic locations, and an implant-retained maxillary obturator was fabricated, showing satisfactory results in the rehabilitation of multiple aspects, including palatal defect, masticatory function, swallowing, pronunciation, and aesthetics.

• Journal of the korean academy of Pediatric Dentistry
• /
• 제31권2호
• /
• pp.153-158
• /
• 2004

Preformed stainless steel crown is an useful restorative material for the treatment of badly broken down primary teeth. However iatrogenic damage to adjacent teeth might occur during the process of tooth reduction. Such damages might lead to plaque accumulation and increase the risks of caries initiation. Especially the damage can make a problem in the first permanent molar. Purpose of this study was to investigate an iatrogenic damage to the first permanent molar during preparation of second primary molar for preformed stainless steel crown. Twelve children restored with preformed stainless steel crown to second primary molar were selected. Contact areas were separated with separation elastics, and tooth surfaces were cleaned. After taking negative impression using vinylpolysiloxane impression material, the specimens were examined by scanning electron microscope for the detection of iatrogenic damage. The prevalence of iatrogenic damage was 66.7% and variable appearances and So we can suggest that when preparing teeth for preformed stainless steel crown, we should be careful about adjacent teeth not to make an iatrogenic damage.

• Journal of Dental Rehabilitation and Applied Science
• /
• 제30권1호
• /
• pp.45-52
• /
• 2014

Diagnosis and treatment planning is initial step to fabricate removable partial denture, and one of most important factor influencing the prognosis. Partial edentulous patients have various condition of remaining teeth and oral mucosa. Therefore, for the proper diagnosis and treatment planning for each patient, getting many informations from patients during initial examination and fabricating accurate diagnostic cast are required. Especially, because the use of various diagnostic tools and surveying of diagnostic cast will be a guide for the abutment teeth selection, oral preparation and design of partial denture, dentist should understand and be able to apply this procedure during diagnosis.

• The Journal of Korean Academy of Prosthodontics
• /
• 제56권2호
• /
• pp.154-160
• /
• 2018

When making conventional removable partial denture for the remaining teeth where the remaining teeth are only on one side, rotation of the denture occurs -in function- on the axis of the connected remaining teeth. If the edentulous portion is long, it becomes harder to obtain retention and stability for the abutment as the importance of the mucous membrane support is elevated. Such movements of denture decrease denture retention and stability, put excessive stress on the abutment, and give bad influence on periodontal health. Therefore, additional implant placement can be of a good choice in gaining additional retention and stability for partial denture. Thus hereby we report this clinical case as successful results were obtained by placing implants symmetrical to the remaining teeth and putting implant-supported surveyed crowns on the implants, allowing the partial denture to be designed to accept varying components and to have suitable path of insertion.

• The Journal of Korean Academy of Prosthodontics
• /
• 제52권2호
• /
• pp.128-135
• /
• 2014

Treatment options for partially edentulous patients are fixed partial denture, removable partial denture and implant supported fixed partial denture. In case of a patient with a few remaining teeth, removable partial denture and implant supported fixed prosthesis are available. For implant fixed prothesis, enough implant fixtures are required and the patient's general condition, local factors and economic status must be considered. When the condition of the abutments and the residual ridge is favorable and the prosthesis is well designed, removable partial denture can be an option. In removable partial denture, the bilateral support is important. If the teeth remain unilateral, harmful stress is put on the abutments by the fulcrum line. In this situation, strategic implantation and implant-retained or assisted removable partial denture is beneficial to the retention and support of the denture. And this can be cost-effective, functional and esthetic choice of treatment. This article describes the prosthodontic rehabilitation of Maxillary Kennedy class I partially edentulous patients. In these two cases, the patients had a small number of teeth and they were restored by the combination of a removable partial denture and dental implants.

• The Journal of the Korean dental association
• /
• 제11권12호
• /
• pp.821-825
• /
• 1973

• Restorative Dentistry and Endodontics
• /
• 제30권2호
• /
• pp.86-94
• /
• 2005

The purpose of this study was to measure the flexural strength and hardness of four core materials in 4 different medias and to evaluate the relationship between the physical properties. For the flexural strength, the specimens were prepared from each of the following materials: Bisfil Core, Core Max, Fuji IX GP, Miracle Mix and randomly divided into four groups and stored at 37 degree C in the following medias: distilled water for 24 hours (DW/1), distilled water for 30 days (DW/30). $2%$ NaF for 30 days (NF/30), 0.02N lactic acid for 30 days (LA/30). After storage, the specimens were subjected to flexural strength testing and calculated to flexural modulus. For hardness testing, specimens were prepared from four materials and storaged in the uniform way. After storage, the specimens were subjected to Vicker's hardness testing. 1. The flexural strength of Core Max were the highest, and the flexural strength of Miracle Mix were the lowest. 2. The hardness of Bisfil Core were the highest. 3. The hardness of Core Max were the highest. 4. The hardness of Miracle Mix were the lowest. 5. $2\%$ NaF and 0.02N lactic acid negatively affected the flexural strength and hardness of four core materials.

• The Journal of the Korean dental association
• /
• 제24권12호통권211호
• /
• pp.988-989
• /
• 1986

• The Journal of the Korean dental association
• /
• 제17권7호통권122호
• /
• pp.485-485
• /
• 1979