• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.4
• /
• pp.15-20
• /
• 2017

Currently, residential air conditioners operate as a heat pump during winter. In this case, the outdoor heat exchanger acts as an evaporator obtaining heat from cold air. On the other hand, it acts as a condenser during summer transferring heat to hot air. The outdoor temperature changes significantly from high to low. Generally, the air-side j and f factors are obtained at a standard outdoor temperature. Therefore, the applicability of the j and f factors under different outdoor conditions needs to be checked. In this study, tests were conducted for a two-row louver finned heat exchanger changing the outdoor temperature to subzero. The effects of the tube-side brine flow rate were also checked. The results showed that air-side j and f factors were essentially constant and independent of the outdoor temperature, suggesting that an extension of j and f factors obtained under standard conditions to a low outdoor temperature is acceptable. All j and f factors agreed within 9% and 3%, respectively. Tests were also conducted by changing the coolant flow rate. Both the j and f factors did not change according to the flow rate, suggesting that the tube-side heat transfer correlation is acceptable.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.37 no.2
• /
• pp.13-21
• /
• 2000

Au-black for the application of the long wavelength infrared absorber has been prepared by evaporating Au under nitrogen gas-filled low vacuum condition. Characteristics of the deposited Au-black were carefully investigated through structural analysis, infrared absorbance measurement, and patterning of the layer, all of which are dependent on the deposition condition. High density of micro-cavity that trapped infrared were obtained, and infrared absorbance in the wavelength range from 3 $\mu\textrm{g}$ to 14 $\mu\textrm{g}$ was found to be about 90% when the Au-black layer was produced under the deposition condition of mass Per area of about 600 $\mu\textrm{g}$/cm$^{2}$ and chamber pressure of above 1 Torr. Photoresist lift-off process could be performed to pattern the Au-black, of which mass per area was below 900 $\mu\textrm{g}$/cm/ sup 2/. In view of absorbance, heat capacity, and pattern formation, the deposition condition of chamber pressure of about 1 Tow and mass per area of about 600$\mu\textrm{g}$/cm$^{2}$ was most adequate for preparing the Au-black as an infrared absorber.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.35 no.5
• /
• pp.299-308
• /
• 2022

This study was conducted to predict the tendency for heat exchange and boil-off gas (BOG) in a liquefied hydrogen tank under sloshing excitation. First, athe fluid domain excited by sloshing was modeled using a multiphase-thermal flow domain in which liquid hydrogen and hydrogen gas are in the saturated state. Both the the volume of fluid (VOF) and Eulerian-based multi-phase flow methods were applied to validate the accuracy of the pressure prediction. Second, it was indirectly shown that the fluid velocity prediction could be accurate by comparing the free surface and impact pressure from the computational fluid dynamics with those from the experimental results. Thereafter, the heat ingress from the external convective heat flux was reflected on the outer surfaces of the hydrogen tank. Eulerian-based multiphase-heat flow analysis was performed for a two-dimensional Type-C cylindrical hydrogen tank under rotational sloshing motion, and an inflation technique was applied to transform the fluid domain into a computational grid model. The heat exchange and heat flux in the hydrogen liquid-gas mixture were calculated throughout the analysis,, whereas the mass transfer and vaporization models were excluded to account for the pure heat exchange between the liquid and gas in the saturated state. In addition, forced convective heat transfer by sloshing on the inner wall of the tank was not reflected so that the heat exchange in the multiphase flow of liquid and gas could only be considered. Finally, the effect of sloshing on the amount of heat exchange between liquid and gas hydrogen was discussed. Considering the heat ingress into liquid hydrogen according to the presence/absence of a sloshing excitation, the amount of heat flux and BOG were discussed for each filling ratio.

• Fire Science and Engineering
• /
• v.15 no.4
• /
• pp.41-48
• /
• 2001

Halogen-based fire suppressing agents have been the most effective fire suppressants and widely used for flammable liquid and electric fire. However they have environmental problems causing stratospheric ozone depletion and globe warming. As a substitution of halon, fire suppression system using fine water mist is one of an effective fire suppressant. Suffocating and cooling effects of water mist are increased by the evaporation characteristics because it has droplet size less than 1,000 $\mu{m}$ and very large surface area. In this study, the extinguishing characteristics of fire was measured with changing of water mist droplet size, flow density; discharge pressure, and fire size. As a result, the extinguishing time of pool fire was shortened with the increase of flow density and in case of low flow density less than 0.5$\pm$0.05 ml/$\textrm{cm}^2$ . min, the extinguishing time was shortened with the increase of droplet size. The cycling discharge was effective for $\eta$-heptane pool fire, and total amount of water mist required to extinguish fire was reduced to a quarter compare with continuous discharge.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.165.1-165.1
• /
• 2016

Zn의 수요는 매년 증가하지만 매장량의 한계로 대체용 물질계가 개발이 필요한 시점이다. Zn보다 상대적으로 풍부하고 동일 두께의 Zn 코팅층과 비교하여 우수한 내식성을 보이는 Al과 Mg의 코팅층을 제작하여 Al-Mg 코팅 강판의 특성 분석 및 평가를 실시하였다. Al-Mg 코팅층은 99.99%의 Al, 99.9%의 Mg target을 사용하여 스퍼터링을 이용하여 냉연강판 위에 코팅하였다. 증발물질과 기판과의 거리는 7cm 이며, 기판은 세척을 실시한 후 클리닝 챔버에 장착하고 ~10-5 Torr 까지 진공배기를 실시하였다. 클리닝 챔버가 기본 압력까지 배기되면 아르곤 가스를 주입하고 기판 홀더에 -800 V의 직류 전압을 인가하여 약 30분간 글로우 방전 청정을 실시하였다. 기판의 청정이 끝나면 아르곤 가스를 차단하고 코팅 챔버로 시편을 이송 후 코팅층 성분의 구성형태에 따라 Al과 Mg을 코팅하였다. Al-Mg 코팅층은 $3{\mu}m$의 두께를 기준으로 Mg wt.%의 비율을 5% ~ 90%까지 변화시키며 코팅하였다. 그리고 후속 공정으로 질소 분위기 $400^{\circ}C$에서 10분간 열처리를 하였다. Al-Mg 코팅층을 주사전자현미경으로 관찰한 결과, 표면에서는 Al-Mg 코팅층에 존재하는 Mg 함량이 높아질수록 grain의 크기가 증가하였고 단면에서는 열처리 전의 치밀한 구조에서 열처리 후에는 주상구조 혹은 grain 구조가 선명해지는 것을 볼 수 있었으며 글로우방전분광기로 Al과 Mg의 성분 비율변화를 확인할 수 있었다. 또한 Al-Mg가 코팅된 강판을 염수분무시험을 통해서 내부식 특성을 확인하였다. Al-Mg 코팅 강판의 염수분무시험 결과, Mg 함량이 낮은 Al-Mg 코팅층은 열처리 후 뚜렷한 내식성 향상을 보였으며 Mg 조성 변화에 따라 일정한 경향성을 보였다. 하지만 Mg 함량이 높은 Al-Mg 코팅층은 열처리 후 급격한 내식성 저하와 함께 시편간의 편자가 커지는 것을 확인 할 수 있었다. 최적의 내식성을 보이는 Mg의 조성을 확인하기 위해서는 향후 보다 변별력이 높은 평가가 결과가 필요하다고 판단되어진다.

• Journal of the Microelectronics and Packaging Society
• /
• v.7 no.4
• /
• pp.1-5
• /
• 2000

Properties of AC applied hot pressed ($Pb_{1-x}Sn_{x}$) Te thermoelectrics were investigated. Mechanical alloying process used to produce alloyed powder to reduce the inhomogeneity and to avoid vaporization of constituents. It showed an increase in the mechanical alloying time with increasing of Sn contents in ($Pb_{1-x}Sn_{x}$)Te. ($Pb_{1-x}Sn_{x}$)Te were sintered at 873 to 923K for 1-4 minutes, under 150 kgf/$\textrm{cm}^2$ by AC applied hot pressng method. The short sintering time of AC applied hot pressing process could reduce the vaporization of Te. The density of ($Pb_{1-x}Sn_{x}$) Te was more dependent on the sintering temperature than the sintering time. The p-n transition was observed at x=0.1 but only p type conduction behavior was observed at more than 20 mol% of Sn compositions. The maximum value of Seebeck coefficient is 250 $\mu$V/K for x=0.2 at 500K. As the amount of Sn increases, the peak value of Seebeck coefficient drops and shifts to higher temperature and the peak value of electrical conductivity decreased with increasing temperature.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.41 no.3
• /
• pp.171-181
• /
• 2017

Two-phase cross flow exists in many shell-and-tube heat exchangers such as condensers, evaporators, and nuclear steam generators. The drag force acting on a tube bundle subjected to air/water flow is evaluated experimentally. The cylinders subjected to two-phase flow are arranged in a normal square array. The ratio of pitch to diameter is 1.35, and the diameter of the cylinder is 18 mm. The drag force along the flow direction on the tube bundles is measured to calculate the drag coefficient and the two-phase damping ratio. The two-phase damping ratios, given by the analytical model for a homogeneous two-phase flow, are compared with experimental results. The correlation factor between the frictional pressure drop and the hydraulic drag coefficient is determined from the experimental results. The factor is used to calculate the drag force analytically. It is found that with an increase in the mass flux, the drag force, and the drag coefficients are close to the results given by the homogeneous model. The result shows that the damping ratio can be calculated using the homogeneous model for bubbly flow of sufficiently large mass flux.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.12
• /
• pp.3546-3552
• /
• 2009

In this study, an analysis code was created for a 190*650*25-mm (W*H*D) parallel-flow evaporator, and research was done on how to increase the heat transfer rate of aluminum PF heat exchanger for application in IDU. After varying the R410A refrigerant up-down flow to two and three passes and the distribution ratio to 1:1:1 and 1:2:2, it was determined that the two-pass flow has a 30% higher partial heat transfer rate and a 25% lower heat transfer coefficient compared to the three-pass flow. As for the distribution ratios of the three-pass flow, 1:1:1 was found to have a lower refrigerant pressure loss than 1:2:2 distribution. It was assumed, though, that the refrigerant distribution had a uniform flow and that its value was thus overestimated in the actual case of maldistribution in each pass.

• Journal of the Korean Institute of Gas
• /
• v.13 no.1
• /
• pp.21-27
• /
• 2009

This paper presents the numerical study on the strength safety of the prestressed concrete outer tank for a LNG storage tank, which is manufactured by sets of membrane panels with special corrugations. This study for a finite element analysis assumes that the membrane panel of the inner tank was fractured and the liquefied natural gas stored in the inner membrane tank was leaked to the prestressed concrete outer tank. The stress and displacement of the outer tank have been analyzed for five different loadings, which are originated by a hydrostatic pressure and a weight of a LNG, a temperature difference, a weight of the prestressed concrete and a boil-off gas pressure. The computed FEM results indicate that the PC outer tank with a storage capacity of 200,000$m^3$ has a good strength safety for a leaked LNG from the membrane inner tank, but the increased cryogenic loadings in which are originated by a leaked LNG decreases the strength safety of the PC structure. This may lead to the collapse of the outer storage tank.

• Korean Chemical Engineering Research
• /
• v.48 no.1
• /
• pp.1-9
• /
• 2010

Since carbon dioxide, $CO_2$, was revealed as a major greenhouse gas, techniques for its separation, capture, and storage have received increasing interest in recent years. Aqueous amines are the most widely accepted $CO_2$ absorbents, but they cause the problems such as high regeneration energy, thermal degradation, and loss of absorbents due to their volatility. Ionic liquids having high thermal stability, extremely low vapor pressure, and capability of selectively absorbing specific gases have been proposed as new $CO_2$ capturing solvents which may potentially replace aqueous amines. By reviewing the ionic liquids having capability to absorb $CO_2$ reported in previous papers, we seek to develop a comprehensive understanding on the factors that influence the $CO_2$ solubility in ionic liquids such as their structures, absorption temperature, pressure, water content, etc., and to estimate the potential of ionic liquids as $CO_2$ separating media.