• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.13 no.4
• /
• pp.32-37
• /
• 1999

The superposing effect of SPCP(Surfoce Induced Plasma Chemical Process) and corona discharge has been studied for rerroval of NOx from industrial flue gases. NOx rermval rates by SPCP, corona discharge and superposing discharge were monitored and compared. Parameters were the concentration and the flow rate of gas, frequency and the type of discharge. Experirrental results showed that NOx removal rate by sUIffPOSing discharge was 10-15[%] higher than that by the other two modes. The higher NOx. rermval rate was observed with the lower frequency of upper electrode in the combined reactor and with the higher frequency of lower electrode. 'The maximum obtainable NOx. rerroval rate by SPCP (18 [W]) and corona discharge (8.5 [W]) was 80[%] and 10[%], respectively. With the combination of the two modes, however, 90[%] of NOx removal rate was observed with the discharge power of 14 [W].14 [W].

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.22 no.10
• /
• pp.1379-1385
• /
• 2018

In the conventional multi-user superposition transmission, the power allocation coefficients of data symbols and the received signal processing of users are determined by the condition of instantaneous channel powers. However, the use of instantaneous channel powers can increase the system complexity. Hence, we consider fixed multi-user superposition transmission using average channel powers. The fixed multi-user superposition transmission can reduce the system complexity because it uses the condition of average channel powers that slowly change over time in order to decide the power allocation coefficients and the received signal processing. In this paper, we analyze the average symbol error rate for the fixed multi-user superposition transmission. In particular, an expression for the average symbol error rate of M-ary Quadrature Amplitude Modulation is derived assuming Rayleigh fading channels. In addition, through the numerical results, we show that the conventional and fixed multi-user superposition transmissions achieve the similar average symbol error rate performances at the user in the severe channel condition.

• Proceedings of the KIEE Conference
• /
• 2001.07c
• /
• pp.1626-1628
• /
• 2001

본 연구는 AC 전원을 인가하여 좁은 전 극간격에서 고수율을 얻을 수 있는 연면방전방식 (Surface Discharge type)과 DC 전원을 인가하여 넓은 전극간격에서 저수율을 가지는 DC방전방식(DC Discharge type)을 중첩방전 할 수 있도록 중첩방전관을 설계 제작하여 각각 독립적인 방전방식을 적용하였을 때의 방전전압, 방전전류, 방전전력 및 오존생성농도를 실험적으로 조사하고, 두 방전방식을 동일공간에 중첩방전하여, 위 실험을 반복하고 중첩방전이 동일방전공간에 투입에너지 밀도를 높임으로써 방전특성 및 오존생성 특성을 비교 분석하였다.

• Korean Journal of Cognitive Science
• /
• v.17 no.3
• /
• pp.151-175
• /
• 2006

A common constraint-range model was suggested to explain the extraction of edge orientation from kinetic occlusion and five experiments were performed to verify this model. Results of the experiments show that the subjects' ability to identify the orientation of the kinetic edge increases as the angle of common constraint-range decreases. If the common constraint-range was fixed, the number of occluded elements or the interval between them had no effect on the accuracy. These results indicate that in the edge extraction process from kinetic occlusion, the angle of common constraint-range plays more important role than the density of background texture, supporting the common constraint-range model.

• Journal of Broadcast Engineering
• /
• v.24 no.5
• /
• pp.785-790
• /
• 2019

In this paper, a new bilateral frame rate up-conversion algorithm using adaptive overlapped block motion compensation is proposed. In this algorithm, the adaptive overlapped block motion compensation is based on the motion complexity of the reference region. As the motion complexity is determined by the size of the previously coded motion estimation prediction, the overlapped block motion compensation method is selected without any additional computational complexity. Experimental results show that the proposed algorithm provides better image quality than conventional methods both objectively and subjectively.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.11
• /
• pp.17-23
• /
• 2010

Titanium alloy is one of the hard processing materials made by the traditional manufacturing method because of the excellent mechanical strength. Ablation of titanium alloy is investigated by using a femtosecond laser which is a regenerative amplified Ti:sapphire laser with 1kHz repetition rate, 184fs pulse duration time and 785nm wavelength. Experiments are carried out under various ablation conditions with different pulse overlap ratios for the rectangular shape and micro hole. Test results show that the ablation characteristic according to pulse overlap ratio of titanium alloy seems to be as non-linear type at the different zone of energy fluence. The optimal condition of rectangular shape processing is obtained at the laser peak power 1.3mW, pulse overlap ratio of 90%, beam gap of $1\;{\mu}m$. The micro hole has a good quality from the pulse overlap ratio of 99% at the same laser peak power. With the optimal processing condition, the fine rectangular shape and micro hole without burr and thermal damage are achieved.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.22 no.1
• /
• pp.78-92
• /
• 2019

This study aims to evaluate the efficiency in the provision of employment services for the middle-aged by using spatial analysis in GIS. Based on location information of employment service institutions, we find service areas of the institutions and calculate regional rates of duplication and exclusion in terms of spatial coverage of the employment services. Taking into account potential demand for employment services, the regions with high priority in the provision of the services are identified. Among the regions, those with high exclusion rate of the services are designated as the regions of insufficient service level. Results indicate that Namyangju-si is a representative region of insufficient employment service level. To improve efficiency in the provision of employment services, we suggest to relocate employment service institutions that have been located in a region of high duplication rate such as Siheung-si, Danwon-gu, Gangnam-gu, Songpa-gu into the locality of Namyangju-si.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.8
• /
• pp.162-167
• /
• 2013

X-ray or ${\gamma}$-ray spectroscopy systems are widely used for analyzing material characteristics. Pile-up pulses are very often encountered for several reasons in XRF systems. Thus, it is necessary to reject or recover pile-up pulses to accurately analyze the material under test. In this paper, a pile up pulse rejection and recovery method is presented for XRF systems using trapezoidal pulse shaping of the input signals. Since the proposed method is based on the trapezoidal pulse shaping method widely-used in XRF systems, only two counters and a few registers are needed to implement the additional function of pile-up pulse rejection and recovery. Consequently, the proposed system is much simpler than conventional pulse reconstruction systems. It is shown that the proposed method can detect and reject pile-up pulses exactly. It is also shown that the pile-up pulses can be recovered if some conditions are satisfied.

• Journal of the Korean Society for Railway
• /
• v.12 no.2
• /
• pp.309-314
• /
• 2009

When a train enters into a tunnel, a compression wave is generated by a front nose and a expansion wave is generated by a rear tail respectively. The interaction between pressure waves and the train makes the internal and external pressure of the train change dramatically. In this paper, we had measured the internal and external pressure variations of TTX and analyzed the pressure variations as the tunnel length. Also, the rate of internal pressure variations were investigated with the current airtight condition of TTX. In short tunnels, the internal and external pressure variation were not large because the superposition of pressure waves was not happened. In long tunnels, however, the rapid and large pressure variations were shown because of the superpositions between the same sort of pressure waves, such as expansion wave and expansion wave or compression wave and compression wave. In specific length tunnels, the pressure variation and the pressure variation rates were largely lessened because the compression wave and expansion wave were superposed.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.162-162
• /
• 2010

InAs 는 광전자 및 광통신 소자에 널리 이용되는 $In_xGa_{1-x}As_yP_{1-y}$ 화합물의 endpoint 로서, Heterojunction Field-Effect Transistors (HEMTs), Heterojunction Bipolar Transistor (HBT) 등에 중요하게 이용되고, 다양한 소자의 기판으로도 폭넓게 사용되는 물질이다. InAs 의 반도체 소자로의 응용을 위해서는 정확한 광 특성과 밴드갭 값들이 필수적이며, 분광타원편광분석법(ellipsometry) 을 이용한 상온 InAs 유전율 함수는 이미 정확히 알려져 있다. 그러나 상온에서는 $E_2$ 전이점 영역에서 여러 개의 밴드갭들이 중첩되어 있어, 밴드구조계산 등에 필수적인 InAs의 전이점을 정확히 정의하기 어렵다. 또한, 현재의 산업계에서 중요하게 여겨지는 실시간 모니터링을 위해서는 증착온도에서의 유전율 함수 데이터베이스가 필수적이다. 이와 같은 필요성에 의해, 22 K - 700 K 의 온도범위에서 InAs 의 유전율 함수와 밴드갭 에너지에 대한 연구를 수행하였다. InAs bulk 기판을 methanol, acetone, DI water 등으로 세척 한 뒤, 저온 cryostat 에 부착하였다. 분광타원분석법은 표면의 오염에 매우 민감하기 때문에, 저온에서의 응결 방지를 위해 고 진공도를 유지하며, 액체 헬륨으로 냉각하였다. 0.7 - 6.5 eV 에너지 영역에서 측정이 가능한 분광타원편광분석기로 측정한 결과, 온도가 증가함에 따라 열팽창과 phonon-electron 상호작용효과의 증가에 의해, 밴드갭 에너지 값의 적색 천이와 밴드갭들의 중첩을 관찰 할 수 있었다. 정확한 밴드갭 에너지 값의 분석을 위하여 2계 미분을 통한 표준 밴드갭 해석법을 적용하였으며, 22 K 의 저온에서는 $E_2$ 전이점 영역에서 중첩된 여러 개의 밴드갭들을 분리 할 수 있었다. 또한 고온에서의 연구를 통해, 실시간 분석을 위한 InAs 유전함수의 데이터베이스를 확립하였다. 본 연구의 결과는 InAs 를 기반으로 한 광전자 소자의 개발 및 적용분야와 밴드갭 엔지니어링 분야에 많은 도움이 될 것으로 예상한다.