• Journal of Power System Engineering
• /
• v.8 no.2
• /
• pp.39-44
• /
• 2004

The effects of the STS 304 hollow cylinder property variations on the non-steady heat conduction are considered in this paper. In the non steady state, the specific heat and conductivity are depended on the temperature variations, and these properties affect to the governing equation on heat conduction. But the most of numerical analysis on heat conduction is assumed to constant properties which is conductivity and specific heat. Assuming that the properties are reacted sensitively, the numerical results can have the difference of between constant properties with non constant properties. The main parameters are specific heat and conductivity. The temperature distributions of the STS 304 hollow cylinder became in steady state after 4 minutes in case of the constant properties. As the conductivity is varied with temperature, the temperature distributions became in steady state after 15 minutes. Therefore, a numerical analysis of the non steady state heat transfer is so important in case of varying temperature.

• Applied Chemistry for Engineering
• /
• v.7 no.1
• /
• pp.109-117
• /
• 1996

Removal of metal ions on the ultrafiltration membrane with micellar-enhanced with anion surfactants is a recently developed technique which can remove heavy metals and small molecular weight ions from wastewater with simple separation process and without a phase change. Above a certain concentration, so called the critical micelle con binding cationic cobalt ions and anionic surfactants, were removed by ultrafiltration membrane. The transmembrane pressure difference had a relatively small effect on the rejection coefficient of metal ions on the ultrafiltration membrane whereas the level of anionic surfactant-to-metal ratio (S/M) had a substantial effect.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.23 no.1
• /
• pp.9-14
• /
• 2019

Hydroxy-terminated polybutadiene (HTPB) propellants of solid rocket motors age differently under different storage temperatures. The shelf life of a solid rocket motor depends on the aging ratio of the HTPB propellant; it can be estimated through the viscoelastic properties by an aging test. This study analyzed the initial and natural aging properties during long-term storage. The initial properties were obtained from characterization and accelerated test results. The test results were obtained by analyzing the strain on cylindrical grains when a thermal load was applied.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.8 no.1
• /
• pp.151-157
• /
• 1988

A series of torsion shear tests were performed according to various stress-paths on hollow cylinder specimens of $K_0$-consolidated clay to investigate the influence of rotation of the principal stresses on the stress-strain and strength characteristics. The effects of stress-paths and reorientation of principal stress were mainly observed in the prefailure stress-strain behavior. The experimentally obtained failure surface from torsion shear tests could practically be modeled by an isotropic failure criterion. Coupling effects between stresses and strains were investigated when both torsion shear and vertical stresses were applied. The work-space in torsion shear tests was illustrated and the relation between stresses and strain increments was also investigated in the work-space.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.1
• /
• pp.1-12
• /
• 1990

The study is concerned with the analysis of combined forging of non-axisymmetric shapes with inclined protrusions by UBET technique. Work hardening is considered for the given range of strain rate during the forging process. A complex shape with inclined cavities is analyzed by subdividing the workpiece into finite UBET elements for which simple velocity fields are applicable. An experimental set-up was designed and manufactured for the experiment, and experiments are carried out with lead billets. The devised set-up can be used for closed-die forging of complex shapes with protrusions in which the dies can be separated automatically for easy removal of the forged products. Based on the derived kinematically admissible velocity fields for corresponding UBET elements, general computer programs have been developed. Since the energy dissipation rate for each elemental region is provided by subprograms (Subroutine or Function), the developed program can be applied to the forging problems of various shapes. The present study has shown that the method developed can be effectively applied to forging of non-axisymmetric shapes with complicated protrusions.

• Membrane Journal
• /
• v.9 no.3
• /
• pp.185-192
• /
• 1999

The ultrafiltration characteristics of wafer processing wastewater produced from semicon¬ductor industry was investigated for wastewater reuse. Using the pilot-scale ultrafiltration system con¬taining poly sulfone hollow fiber membranes (MWCO : 10,000, 20,000, 30,(00), the membrane performance, such as flux, rejection rate and concentration factor for flux was examined. The SDhs, turbidity, electrical conductivity and concentration of Si particles were measured, and the possibility of permeate reuse was validated from the experimental results. It was shown that the flux was recovered by the sweeping with air and water effectively. The permeate flux of 30,000 MWCO membrane was about 5 times higher than that of 10,000 and 20,000 MWCO membranes. The concentration of Si particle in the saw wastewater was analyzed 3.8-5.6 mg/$\ell$ and that of Si particle in the permeate was analyzed less than 0.2${\mu}g$/$\ell$. This means the rejection of silicon particle was over 96%.

• Membrane Journal
• /
• v.28 no.4
• /
• pp.243-251
• /
• 2018

Methane is one of the important greenhouse gases and methane is the major component of the biogas. A multiple stage membrane process was developed and analysed with the numerical analysis so that the mole fraction of methane in the final product could be kept higher than 0.95 and simultaneously the recovery of methane was also maintained higher than 99% from the biogas using 3 polysulfone hollow fiber membrane modules which were properly connected. As the feed pressure of the biogas, the mole fraction of methane in the biogas and the membrane area in the membrane module are increased, the methane mole fraction of the final product are found to be increased. However, a proper membrane area in the module should be carefully selected in order to achieve the satisfactory goal of 0.95 mole fraction of methane and 99% recovery of methane from the biogas. Even if the multiple membrane process is utilized with the properly selected membrane modules, the limited operating ranges have to be applied in the following parameters : the feed pressure, the flow rate, the mole fraction of methane in the biogas to get both the target methane concentration and the recovery rate of methane.

• Membrane Journal
• /
• v.9 no.4
• /
• pp.202-208
• /
• 1999

The car washing effluent containing various oils and detergent was treated by ultrafiltration membranes. Dead-end type stirred cell (Amicon 8050) with 10, 30 and lOOk dalton membranes was used to determine permeation and rejection characteristics for the car washing effluent. In case of low molecular weight cut-off membranes, the effect of membrane fouling was weak under the applied pressures. However, the permeation flux for YM100 membrane(look dalton) may be affected by oil layer formation on the membrane surface as well as oil particle plugging for a part of membrane pores due to compressible and deformable oil properties. Oil and particle rejections in the permeates were over 95%, but detergent was passed easily through the membranes. Hence, the permeates containing detergent can be recycled to the system, and may reduce water pollution. Also, the car washing effluent was treated continuously by a capillary type ultrafiltration membrane of MWCO 50k dalton. The experimental data were fitted suitably to the cake filtration model.

• Membrane Journal
• /
• v.7 no.3
• /
• pp.131-135
• /
• 1997

Polymeric micellar enhanced ultrafiltration method using a new type of polyrmer, $\alpha$-allyl-$\omega$-methoxy polyoxyethlene and maleic anhydride copolymer (AKM-0531, Mw 15, 000), has been proposed to separate 1-naphthylamine as a weak cationic toxic organic solubilizate. Enhancement effect of polymeric micelle was identified by the ultrafiltration runs using polyacryronitrile(PAN) holow fiber membrane with molecular weight cut off 6, 000. The linear dependance of flux on the pressure difference is shown to be valid up to 0.6kg/${cm}^2$ and the rate of flux increase in response to change in the pressure is gradually reduced under the pressure difference. Rejection of 0.96 was observed for f mM of 1-naphthylamine with 2 wt.% polymer solution at the conditions of 0.4kg/${cm}^2$, natural pH. and $25^{\circ}C$ Solubilization of 1-naphthylamine into the polymeric micelle enhanced the separation efficiency.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.28 no.3
• /
• pp.334-339
• /
• 1983

With the 91 lines of Italian millet collected throughout the whole country in Korea and the 238 varieties from several Asian countries, trial was carried out to elucidate its differentiation, dissemination and distribution, and the ethnobotanical relations to the adjacent area. Glutinous millets which consisted of 66% among the collected Korean lines were widely distributed throughout the whole country, but non-glutinous ones were mainly distributed in the mountainous regions and Jeju island. The variations in germinability at low temperature were recognized among lines, but seemed not to be closely related to their regional distribution. The collected lines with small grain size were distributed mainly in the mountainous regions of middle and northern part of Korea and larger ones in Jeonnam province and Jeju island. And some of them were larger in grain size as compared with that of Japanese and Republic of China varieties. Seed coat color of collected lines in Korea showed wide variations from yellow to gray, especially in Gyungbuk province. However, all lines from Chungnam, Jeonnam and Gyungnam province were yellow in seed coat color. All lines from Korean collection except two lines indicated negative(-) phenol reaction which is very similar to that of Japan and China, while these were quite different from the varieties of Republic of China, Philippines and India, of which 30-60% showed positive(+) phenol reaction. The pattern of the esterase isozyme m Korean lines was simillar to that of Japanese lines and this was quite different from that of Republic of China, Philippines and India. Variation of this trait was greater in Chinese and Korean lines.