• International Journal of Highway Engineering
• /
• v.6 no.1 s.19
• /
• pp.1-11
• /
• 2004

This study tries to propose the most effective pavement texture method through the performance evaluation of variable texture methods. Noise 2$\sim$3dB is reduced in the section of uniform space 18m longitudinal tinning. This result is proved by comparing the magnitude of noise in two sections. The noise of 26mm longitudinal firming section is greater than that of 18mm section by 2$\sim$3dB(A). The skid resistances measured in all test section show the reasonable results. The roughness or all the test sections satisfies AASHTO roughness standard (PrI 16cm/km). The result or questionnaire survey about driving quality shows that the longitudinal tinning is the most effective method. As the result of a visual measurement, it is proved that the section applied uniform space 26mm longitudinal tinning and the general section applied uniform space 26mm transverse tinning could drain water effectively. As the result of analysis with the ranking method, the 18mm longitudinal tinning in selected as one of the most effective tinning methods. In addition, 26mm longitudinal tinning, random space transverse tinning, and transverse drag are selected in order.

• International Journal of Highway Engineering
• /
• v.6 no.4 s.22
• /
• pp.123-136
• /
• 2004

This study tries to compare the noise difference by various surface treatments and to propose appropriate tinning methods. As literature reviews, longitudinally tined pavement is effective to reduce noise made between tire and pavement surface. Various surface treatments were applied to some sections of test road. In case of car, about 2$\sim$3dB(A) was reduced in the section of uniform space 18mm longitudinal tinning. The peak frequency point for truck case happened between 200 and 600 Hz. The maximum noise of car was measured at about 1000Hz. Therefore, it Is proved that surface treatment methods can have a large affect on noise generation. With a result that friction test, the transverse tined pavement showed better frictional characteristics than the longitudinally tined pavement, but as a whole it came out satisfactory result. Results from this study are of early age, so it is required to check the performance continuously.

• 한국도로학회지:도로
• /
• v.8 no.4 s.30
• /
• pp.6-15
• /
• 2006

• Proceedings of the KIEE Conference
• /
• 2006.07c
• /
• pp.1581-1582
• /
• 2006

본 논문은 그루빙(grooving), 타이닝(tining), 텍스쳐(texture) 등의 포장도로의 표면 상태를 차량에 장착된 고성능의 레이저 변위센서를 사용하여 주행 중에 정밀하게 측정하는 도로 표면 측정 장비 개발에 관한 논문이다. 본 논문에서는 전체 시스템을 설계 및 시험제작 하였으며, 차량 주행을 모사한 실험 모형을 이용한 실내 실험 및 시험도로에서의 실제 도로 표면 측정 실험을 실시하였다. 실내 포장도면 모사장비를 이용한 실험 결과 타이닝 폭 오차 2%, 깊이 오차 4%(60km/h)를 얻었으며, 실외에서 차량에 레이저센서를 장착 후 측정한 실험에서는 폭 오차 3.24%, 깊이 오차 5% (50km/h)가 측정되었다. 이러한 실험 결과를 토대로 시험도로 상의 실제 도로 표면 측정 실험에서는 25mm, 18mm, 26mm, 그리고 임의의 간격의 횡 방향 및 종 방향 타이닝을 측정하였고 이를 확인하였다.

• International Journal of Highway Engineering
• /
• v.6 no.4 s.22
• /
• pp.35-43
• /
• 2004

Skid resistance is an important factor that control braking distance and secure safety by preventing slipperiness between tire and pavement surface. Decrease of skid resistance at wet condition may cause fatal traffic accidents. Dirt materials such as sand and do-icings on the road surface also can be a factor for decrease skid resistance. This study makes an investigation into influence of skid resistance between varied cement concrete pavements about surface texturing method(transverse tining, longitudinal tining, exposed aggregate surface texturing method) and wearing condition of pavement surface texture(new constructed pavement's surface, wore pavement's surface) using accelerate concrete pavement wearing tester when remains of dirt material are obtained between tire and road surface on PCC pavement. As dirt material on road surface of concrete pavement, sand, calcium chloride and old oil were used with different amount of each cases.