• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.9
• /
• pp.17-24
• /
• 2020

This study examined the spectral information and reflectance of cracks of an embankment with drone-based hyperspectral imagery for crack detection. A Nano-Hyperspec mounted on a drone was used as a sensor, and hyperspectral videos of different intensities of illumination of the cracks on the embankment located in the downstream of Andong-Dam were obtained. An analysis of the data value of the illumination and peak data-value, the coefficients of determination were calculated to be 0.9864 of the uncracked areas and 0.9851 of the cracked area. The reflectance of each area showed a similar value and pattern, regardless of the intensity of illumination. This result may have occurred because the reference values of the white reference as the calculation criteria of reflectance varied according to the intensity of illumination. The reflectance at the cracked area was 5.65% lower in visible light and 4.58% lower in near-infrared light than that at the uncracked area. The detection of cracks may offer more precise results in further studies when the gimbal direction and camera angles of the drone are calibrated. Because hyperspectral imagery enables the detection of crack depths and types of clay minerals, which are difficult to identify in general RGB imagery, it can serve as a preemptive measure for evaluating the embankment stability.

• Science of Emotion and Sensibility
• /
• v.18 no.2
• /
• pp.45-54
• /
• 2015

This study carried out an experiment to identify subject's work effectiveness and energy saving effect using LED light. Towards this end, this study configured nine various lighting environments in order to control PWM (Pulse Width Modulation) and illuminance (lux), which are the characteristics of LED light. The PWM ratio of LED light was set as R:G:B=1:1:1, R:G:B=4:1:5, and R:G:B=8:7:7, respectively, and illuminance (lux) was set as 400 lx, 700 lx, and 1000 lx, respectively. In addition, the indoor environment was set temperature $20-24^{\circ}C$, humidity 50%-60%, and the amount of clothing 1. This study analyzed work effectiveness and energy consumption in nine lighting environments, each. Error correction was performed for work effectiveness analysis, and cumulative power consumption was measured in each lighting environment for energy consumption analysis. According to experiment results through the lighting environments suggested in this study, accuracy and spent time effectiveness were good in 700lux and higher than 400lux. For spent time, the best effectiveness was revealed in the suggested PWM ratio, R:G:B=8:7:7. The lowest power consumption on each illuminance (lux) was revealed in the order of R:G:B=8:7:7, RGB=1:1:1, and R:G:B=4:1:5. Therefore, pulse-width modulation effect is proposed in this paper was found to affect the efficiency and energy saving.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.28 no.3
• /
• pp.74-82
• /
• 2024

In this study, feature point detection and displacement measurement performance depending on feature extraction algorithms were compared and analyzed according to environmental changes and target types in the feature point-based displacement measurement algorithm. A three-story frame structure was designed for performance evaluation, and the displacement response of the structure was digitized into FHD (1920×1080) resolution. For performance analysis, the initial measurement distance was set to 10m, and increased up to 40m with an increment of 10m. During the experiments, illuminance was fixed to 450lux or 120lux. The artificial and natural targets mounted on the structure were set as regions of interest and used for feature point detection. Various feature detection algorithms were implemented for performance comparisons. As a result of the feature point detection performance analysis, the Shi-Tomasi corner and KAZE algorithm were found that they were robust to the target type, illuminance change, and increase in measurement distance. The displacement measurement accuracy using those two algorithms was also the highest. However, when using natural targets, the displacement measurement accuracy is lower than that of artificial targets. This indicated the limitation in extracting feature points as the resolution of the natural target decreased as the measurement distance increased.

• Journal of Korea Water Resources Association
• /
• v.47 no.12
• /
• pp.1121-1134
• /
• 2014

The distributed watershed model of rainfall-runoff-soil erosion-sedimen transport was constructed for the Naesung Stream Watershed with high potentiality and risk of sediments produced by soil erosion. The sensitivity analyses of roughness coefficient and hydraulic conductivity which affected the modeling results of runoff and sediment concentration were performed in this study. As a result, the change of the roughness coefficient for the forest area from 0.4 to 0.45 did not affect the change in runoff and stream discharge and the average value and range of sediment concentration were also insignificantly increased with few difference. As a result of the sensitivity analysis of the hydraulic conductivity, the total amount of runoff and maximum runoff were gradually increased as the hydraulic conductivity was reduced. In the case of sediment concentration modeling, the average and the range of sediment concentration for all stations were increased as the hydraulic conductivity was decreased. For the Hyangseok Station, in case of the hydraulic conductivity reduced by 50%, the simulation result of sediment concentration was most similar to the estimated value by the sediment rating curve.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.11 no.4
• /
• pp.527-534
• /
• 2023

This paper conducted a study on the application of ceramic materials for bridge bearing that can complement the durability of PTFE, a conventional bridge bearing friction material, and exhibit low coefficient of friction and friction behavior without lubricant. The ceramic material was zirconia (ZrO₂), and the friction behavior was evaluated according to the roughness coefficient. The roughness coefficient was divided into 0.8 and 0.027, and the average coefficient of friction was calculated to be 0.16 under 15 MPa surface pressure. Afterward, ceramic was made into friction material and applied to the bridge bearing, and performance comparison with PTFE bridge bearing was conducted through compression test and friction test. In the compression test, the ceramic and PTFE bridge bearing showed ideal compression behavior depending on the load. No fractures or defects were observed in the ceramic bridg bearing, but lubricant loss was observed in the PTFE bridge bearing. The average coefficient of friction of the ceramic bridge bearing analyzed through friction behavior was 0.16. The inherent material properties of the physical and chemical properties of ceramics, the excellent mechanical properties derived from the performance evaluation, and the coefficient of friction of 0.16 suggest that it can be considered as a friction material.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.9 no.1
• /
• pp.134-139
• /
• 2005

This paper works on the manufacture and performance evaluation of bi-polar power supplied diesinking electrical discharge machine. The design and implementation of diesinking electrical discharge machine consists of two parts which are a polarity voltage controller design and a servo motor controller design and they are verified and manufactured through simulation. The performance of the implemented machine and conventional one were evaluated by comparing its machining speed and roughness of machined surface. Eventually, the designed machine showed improved performance in the speed and the roughness.

• KIEAE Journal
• /
• v.4 no.3
• /
• pp.27-35
• /
• 2004

The conventional way to acquire sufficient amount of daylight in interiors is to provide large openings with clear glass. The use of clear glass on the whole facade, however, might cause a sort of visual problem because of the harness of direct sun and brighter sky surface than expected. They should be filtered in opticalway or bounced in the architectural. One of the common solutions for the problem might be the use of photometric glasses with various transmittances for the glass walls. This paper deals with performance data related to the impact of various transmittal glazing materials for window systems in terms of daylighting. A series of scale model measurements was carried out with the fundamental configuration of a commonly used all-glass facades. Additionally some experimental performance index was issued for the better expression of the need of natural lighting.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2017.05a
• /
• pp.124-124
• /
• 2017

Fe-Ni-Co 합금 박막(<$100{\mu}m$)을 황화물계 용액에서 전주공정으로 제조하였다. XRF로 측정한 박판의 평균 조성은 Fe-34 wt.% Ni-3 wt.% Co 이다. AFM으로 측정한 표면 조도는 35.2 nm 이다. 표면의 나노 경도는 평균 5.4 GPa 이었다. Oliver 모델을 적용한 구리 박막의 탄성하강강성도는 약 75 이었다. Alekhin 모델을 적용한 구리 박막의 마찰계수, 피로한계는 각각 0.134, 0.027 이었다. 유한요소법으로 평가한 Berkovich 형 나노압침선단의 하중분포를 이차원 선형 및 비선형 해석하면 1 [mN]의 정적하중을 가한 Fe-Ni-Co 박막은 약 576 [mN]로 예측되었다. 압침선단의 하중집중정도는 표면탐침현미경으로 관찰한 압흔의 변형정도와 유사한 경향을 보였다.

• Proceedings of the Korean Society of Disaster Information Conference
• /
• 2016.11a
• /
• pp.428-432
• /
• 2016

자연재해는 전 세계적으로 몇 조원에 이르는 피해를 주고 있으며 근래에는 기후변화로 인한 이상기후현상으로 집중호우의 빈도가 증가하고 있으며 홍수, 산사태 토석류 등 발생빈도가 늘어나고 있는 추세이다. 최근 2011년 서울에서 발생한 우면산 토석류의 피해와 강원도 일부 지역의 피해로 인해 많은 피해가 일어났으며, 국가에서는 산사태 피해를 최소화하기 위해서는 장기적으로는 위험한 지역에 구조물을 설치하는 등 예방사방을 실시하고, 단기적으로는 위험요소의 제거와 위험지역의 예측을 통한 경계피난체재를 철저히 할 필요성이 강조되고 있는 실정이다. 특히, 강원도는 산지로 이루어져 있으며, 매년 집중호우나 태풍이 지나간 다음, 많은 양의 강우량으로 인해 산길을 지나는 도로에 토석류로 인해 길이 막혀 이동이 불가능 하게 되거나 산지 아래에 있는 건물이 산에서 쓸려서 내려오는 토사와 나무에 의해 파괴되어 물질적인 피해를 입는 영상이 뉴스를 통해 많이 접하고 있다. 본 연구에서는 토석류에 대한 전반적인 특성을 설명하고 체계적인 관리가 필요하다. 연구 지역은 춘천지역을 대상으로 SINMAP 모델 기법의 조도계수와 특성을 고려한 위험지도를 작성하였고 산사태 일부 지역에 대한 위험도 평가를 하였다.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2010.05a
• /
• pp.704-708
• /
• 2010

하천에 있어서 저수호안의 수충부는 수리학적 안정성이 요구되는 부분이나 이에 대한 신뢰성있는 자료와 적정 공법의 선정 방안이 마련되어 있지 않고 있으며, 국내 자연형하천 조성을 위하여 하천하안에 적용된 공법들은 대부분 콘크리트블록, 발파석, 강화석, 전석, 잡석 등 견고한 재료를 활용한 공법이었다. 최근 하천의 생태환경 조성으로 인하여 식생에 의한 공법 개발이 활발하게 진행되고 있으나 이의 치수적인 평가는 진행되고 있지 않으며, 이들 각종 공법의 적용여부는 주로 소류력의 평가에 의한 것으로 하천의 생태적 환경보다는 치수적인 관점에서 적용되고 있다. 국내 생태하천의 경우 호안의 경사가 1:2~1:5정도로 매우 완만한 것이 보통이며, 급강하 하천이 아니기 때문에 설계유속은 2~3m/s 정도이다. 본 연구에서는 경사에 따른 호안의 안정성을 검증하기 위하여 3차원 모델인 Flow-3D를 이용하여 길이 20m, 폭 2m, 높이 1m의 개수로 장치를 구성하였으며, 호안의 조도변화에 따른 유량별 2차원 유속분포 및 Froude수를 산정하여 분석하였다.