• Journal of the Korean Society of Propulsion Engineers
• /
• v.16 no.5
• /
• pp.97-107
• /
• 2012

In general, solid propulsion offers cost effective, large thrust capabilities comparing to the liquid propulsion which offers high specific impulse and restart capabilities. Therefore, solid propulsion is well fitted for the first stage and boosters. Building Block Launcher(BBL) approach has been studied for the launch vehicle because of cost effectiveness, limited development time and low risk. Using of the carbon fiber epoxy resin in the solid rocket motor case is expanded, and specially high strength fibers are more attracted since its inert mass reduction.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.33 no.12
• /
• pp.48-53
• /
• 2005

In this paper, we present our recent progress in the LIPCA (Lightweight Piezo-Composite Actuator) application for actuation of a flapping wing device. The flapping device uses linkage system that can amplify the actuation displacement of LIPCA. The feathering mechanism is also designed and implemented such that the wing can rotate during flapping. The natural flapping-frequency of the device was about 9 Hz, where the maximum flapping angle was achieved. The flapping test under 4 Hz to 15 Hz flapping frequency was performed to investigate the flapping performance by measuring the produced lift and thrust. Maximum lift and thrust were produced when the flapping device was actuated at about the natural flapping-frequency.

• Aerospace Engineering and Technology
• /
• v.12 no.2
• /
• pp.180-185
• /
• 2013

In this study, preliminary design of human powered aircraft was performed by considering the aerodynamic performance. For this, overall weight including the aircraft and pilot was determined. Then, the main wing and horizontal/vertical tail were designed with appropriate selection of the airfoils and planform shapes. Based on these, three dimensional flow was calculated to obtain lift and drag coefficients and the position of center of gravity (CG). Consequently, it was shown that the lift and power of the aircraft satisfied the constraints of the minimum required lift and the pilot's available power. Also, the CG of the aircraft was located at aerodynamic center (AC) of the main wing, which guaranteed 26% of the static margin.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.31 no.3
• /
• pp.72-78
• /
• 2003

In this paper, the feasibility study and the parametric design of hybrid motor with HTPB/LOX were conducted for micro air launch system. Design results were compared with 1st stage of Pegasus XL for verification of hybrid motor. Results showed that hybrid motor replace solid booster if Isp of hybrid motor reaches 330sec. In addition, mission analysis was established for micro air launch system, and parametric design was conducted with design variables: number of port, initial oxidizer flux, and chamber pressure. And the region of Isp was identified by parametric study which satisfied design constraints and mission analysis.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.04a
• /
• pp.365-369
• /
• 2007

The solid rocket interacts circumscriptively in terms of is many more than liquid rocket. It is uncontrollable than liquid rocket because all part of combustion is decided such as Mixture ratio of propellant, burning time and area. However, production cost is cheap and because authoritativeness security can be easy and enlarge the early speed that follow thrust-to-weight ratio, it is used comprehensively by small size rocket. Considered about nozzle cooling to control phenomenon that burn by thermal conduction in interior wall of nozzle that follow in thrust increase of solid rocket and erosion phenomenon by combustion gas of high speed.

• The Bulletin of The Korean Astronomical Society
• /
• v.37 no.2
• /
• pp.148.1-148.1
• /
• 2012

로켓 혹은 우주발사체의 주엔진에는 대부분 연료와 산화제를 연소시켜 나오는 에너지를 사용하는 화학로켓이 주종을 이루어 왔다. 이러한 로켓엔진에서 그동안 연료로는 수소계, 탄화수소계, 아민계 등 다양한 화학물질이 사용되어 왔으나, 산화제로는 강한 산화성을 나타내면서 밀도가 높은 몇몇 물질만이 제한적으로 사용되어져 왔으며, 최근에는 주로 액체산소(LOx)와 사산화질소(N2O4)가 사용되고 있다. 그러나 산화제 중 액체산소는 극저온이면서 상대적으로 밀도가 낮고, 사산화질소는 강한 독성을 지니고 있으며 액체로 존재하는 구간이 좁아 연구 목적의 소형발사체를 구현하는 것에는 많은 어려움이 있다. 이러한 이유로 최근 소형발사체 개발분야에서는 상온저장성이면서 친환경적인 과산화수소(H2O2)와 아산화질소(N2O)를 산화제로 활용하는 것에 대한 관심이 고조되고 있으나, 대형 추진기관을 개발하는 연구자들로부터는 액체산소를 사용할 때 보다 엔진 자체의 비추력이 상대적으로 낮다는 이유로 활용이 외면되어 온 것이 사실이다. 본 연구에서는 엔진 자체의 추진성능 보다는 사실상 발사체의 목적이라고 할 수 있는 추진단 속도증분을 성능의 지표로 삼아 평가하였으며, 결과를 통하여 과산화수소와 아산화질소의 높은 밀도가 엔진의 낮은 비추력을 충분히 보상할 수 있음을 보였다. 과산화수소와 아산화질소는 교육/연구용 소형발사체 구성에 충분히 활용가능한 산화제이며, 실제 발사에서 충분한 비행성능을 기대할 수 있는 물질로 평가할 수 있다.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.04a
• /
• pp.93-96
• /
• 2011

A genetic algorithm (GA) has been employed to optimize the major design variables of the liquid rocket engine. Mass flow rate to the main thrust chamber, mass flow rate to the gas generator and chamber pressure have been selected as design variables. The target engine is the open gas generator cycle using the LO2/RP-1 propellant. The objective function of design optimization is to maximize the specific impulse with condition of energy balance between the pump and the turbine. The properties of the combustion chamber have been obtained from CEA2. Pump & turbine efficiencies and properties of the gas generator have been modeled mathematically from reference data. The result shows 3~4% errors for the specific impulse and 2~6% errors for the pump power of the gas generator cycle compared to references.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.43 no.8
• /
• pp.692-698
• /
• 2015

This paper represents a trajectory design and analysis technique which uses invariant manifolds of the circular restricted three body problem. Instead of the classical patched conic method based on 2-body problem, the equation of motion and dynamical behavior of spacecraft in the circular restricted 3-body problem are introduced, and the characteristics of Lyapunov orbits near libration points and their invariant manifolds are covered in this paper. The trajectories from/to Lyapunov orbits are numerically generated with invariant manifolds in the Earth-moon system. The trajectories in the Sun-Jupiter system are also analyzed with various initial conditions in the boundary surface. These methods can be effectively applied to interplanetary trajectory designs.

• Aerospace Engineering and Technology
• /
• v.3 no.1
• /
• pp.27-34
• /
• 2004

Tail-wing, gondola and thrust motor mount(EMS) were built by carbon/glass fiber composites. Structural strength & stiffness was verified by specimen tests. Static strength tests for each structural components were conducted separately. Boundary conditions are specially designed for each components to simulate exact joint conditions. Tests shows no detriment deformation at 100% DLL and no failure at 150% DLL.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1998.04a
• /
• pp.35-35
• /
• 1998

고체 로켓 추진기관의 노즐을 개발하기 위해서는 주어진 체계 제한 조건내에서 기본적인 가스의 동력학, 내탄도에 의한 형상 설계, 재료 개발 및 적용 기술, 열전달 계산에 의한 열설계 및 해석 등이 종합적으로 적용되며 수많은 반복과정을 거쳐야 한다. 특히 최근에는 알루미늄 함유량을 증가시켜 연소가스의 온도가 300$0^{\circ}C$ 이상이 되는 고성능 추진제가 일반적으로 적용되고 있으므로 고온에 의한 열적문제가 심각하게 대두되고 있으며 이에 견디는 신뢰도가 높은 노즐 설계개발이 요구되고 있다. 노즐목을 노즐내에서 열부하가 가장 심한 곳으로 노즐목 확대에 의한 추력 손실을 최소화하기 위해 내삭마성이 강한 재료를 선정하여야 하며, 그래파이트는 이러한 조건을 만족시키는 소재의 하나로 많이 적용되고 있다.