• 소음진동
• /
• 제5권4호
• /
• pp.493-501
• /
• 1995

Optimum design of a viscoelastic damping layer which is unconstrainedly cohered on a steel plate is discussed from the viewpoint of the modal loss factor. Themodal loss factor is analyzed by using the energy method to the base steel plate and cohered damping layer. Optimum distributions of the viscoelastic damping layer for modes are obtained by sequentially changing the position of a piece of damping layer to another position which contributes to maximizing the modal loss factors. Analytical procedure performed by using this method simulated for 3 fundamental modes of an edge-fixed plate. Simulated results indicate that the modal loss factor ratios can be increase by as much as 210%, or more, by optimizing the thickness distribution of the damping layer to two times of the initial condition which is entirely covered. Optimum configurations for the modes are revealed by positions where added damping treatments become most effective. The calculated results by this method are validated by comparison with the experimental results and the calculated results obtained by the Ross-Ungar-Kerwin's model in the case of the layer is uniformly treated over the steel plate.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1995년도 춘계학술대회논문집; 전남대학교, 19 May 1995
• /
• pp.292-297
• /
• 1995

본 연구에서는 점탄성 제진층이 탄성기판의 한 면에 피복된 2층 제진강파느이 모달 손실계수의 관점으로부터 부분도포에 의한 최적설계의 가능성을 검토하였다. 즉, 일정한 두께로 전면 도포되어 있는 2층의 제진층을 작은 크기의 조각(piece)으로 분할한 경우, 각각의 조각이 손실계수에 미치는 영향을 손실계수의 증감율로써 평가하고, 최소 영향부위의 조각을 최대 영향부위에 이동하여, 동일 질랴의 제진재로 최대의 제진효과를 얻을 수 있는 제진재의 최적 설계법을 제안한다. 수치계산은 주변고정 평판의 (1,1)(1,2)(1,3) 모드 성분에 대해 수행하여 최적설계에 의한 손실계수의 증가와 그때 제진재의 배열형상을 조사하였다. 본 수법에 의해 얻어진 결과는 실험결과와 비교 검토하여 본 최적화 수법의 타당성을 확인하였다. 또한, 제진재의 전면도포의 경우는 Ross-Ungar-Kerwin모델에서도 계산을 수행하여 본 수법의 결과와 비교하였다.

• 분석과학
• /
• 제8권1호
• /
• pp.85-90
• /
• 1995

4종류의 Fe-Al 제진합금의 3.5% NaCl 염수에서의 부식특성을 냉간압연강판 및 순수한 티타늄과 함께 연구하였다. 티타늄의 경우 부동태현상이 관찰되었으나 Fe-Al 제진함금과 냉간압연강판의 경우 부동태현상이 관찰되지 않았다. 탄소 함유량이 적을수록 부식속도가 낮은 값을 나타내었다. 그러나 제진특성 향상을 위하여 첨가한 Mn은 고철에서는 부식속도를 저하시키는 효과를 보았으나 전해철에서는 부식속도를 오히려 증가시키는 경향을 보였다. Fe-Al 제진합금의 부식속도는 순수한 티타늄보다는 높은 값을 보였지만 냉간압연강판보다는 훨씬 낮은 값을 나타내었다.

• 한국기계가공학회지
• /
• 제20권12호
• /
• pp.24-29
• /
• 2021

Recently, owing to the high demand for eco-friendly cars in the automotive industry, noise and vibrations have become major challenges. The use of laminated damping steel is increasing in response to these demands. Laminated damping steel is primarily used in sound insulation plates. The vibration energy is converted into thermal energy due to the viscoelastic resin being located between two steel sheets and being able to damp the vibrations when an external force, such as, noise or vibration is applied to the steel plate. Laminated damping steel is chiefly applied to dash panels in automotive body parts, and because of its structure, junction technology for bonding with other components is necessary. However, there has not been sufficient research conducted on junctions. In this study, regardless of the electrode shape, in the range of 4.0 ~ 8.0 kA welding current, the same welding force and welding time were applied which were 2.8 kN and 200 m/s (12 cycles) and the tensile shear load and nugget size were analyzed after the resistance spot welding between different materials of laminated damping steel with a thickness of 1.035 mm. The results show that in the range of 5 ~ 8 kA welding current, 1.035 mm laminated damping steel meets the MS181-15 standard, which is the technical standard of Hyundai-Kia Motors.

• 한국소음진동공학회논문집
• /
• 제11권9호
• /
• pp.391-397
• /
• 2001

The characteristic values of damping materials are variant on frequency and temperature. We measure the characteristic values(loss factor, young\\\\`s modulus) of damping materials in vibration test. We can not measure characteristic values of damping materials by themselves. So, we proposed a method, sticking damping material to thin steel beam and measuring of characteristic values of damping material on frequency and temperature. We didn\\\\`t use constraining layer but we measured characteristic values on conditioning temperature.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 제4회 박판성형 심포지엄
• /
• pp.29-34
• /
• 2003

In order to study the shearing characteristics of anti-vibration sheet metal which has been bonded by resin, a blanking die of 40.02mm was manufactured to blank a material and it is used to reduce vibrational noise. The variables employed in this study were 1) Clearance 2) types of stripper plate, and 3) types of the die design technique. These variables were used to study the effects on burr height, diameter of product, and camber height. Lastly, the effect of the position of the rubber during blanking was observed. In the case of burr height from experimental investigation, the push-back die, combined with a movable stripper plate, resulted in the concentration of additional pressure between the cutting edges, meaning the crack initiation was delayed. This result was not affected by lubrication, although appropriate lubrication is preferred to enable a longer lasting die in terms of wear, which results from the presence of adhesive as the sheet metal is blanked. In the comparison of diameter measurement, the push-back die, combined with the back pressure from the knock-out plate showed a favorable precision. The use of the push back die with a fixed stripper plate, with a $4.5\%$ clearance, showed better accuracy in the diameter measurement. For comparing camber height, the push back die resulted in less cambering than the drop-through die. Also, the larger the clearance, the greater was the camber height. Considering experimental results, the shearing of anti-vibrational sheet metal is best achieved when the rubber is laying on the top, blanked with a fixed-stripper plate in a push-back die, with a $4.5\%$ clearance.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1994년도 박판성형기술의 진보
• /
• pp.99-118
• /
• 1994

In recent years reduction in noise and vibration in automobile has been strongly required not only from the standpoint of environmental regulations but also for raising the commercial value and ride comfort. Vibration damping steel sheets, which are composites made by sandwitching a visco-elastic resin layer between two steel sheets, have been developed as effective noise-abating materials and have found a growth of use in automobile industries. Vibration damping steel sheets for commercial use must be excellent in vibration damping property, press formability and spot weldability, but are inferior to ordinary steel sheets. In this study, the mechanical properties of vibration damping steel are evaluated, and press formability is analysed on the basis of those properties and shear bonding strength. The development of engine oil pan using damping steel sheets are also reported, focusing on serious problems in oil pan drawing.

• 동력기계공학회지
• /
• 제6권4호
• /
• pp.36-42
• /
• 2002

In the structures of automobiles and ships which have engines for works, the vibration energies generated by the engines are transferred to dissipation parts through the structures which is welded and bolted with beams and plates. The vibration energies generated by resonance frequencies are the reasons of the resonance phenomena. To solve these problems, up to the present, we have studied to avoid the resonance, and add the higher damping characteristics. However, we need to understand the structural energy flows, to design the structures clearly which have the characteristic of welding. The object of this study is to make differences clear in the characteristics of structures which have some welded part on an homogenous flat plate. In this investigation, we study the flows of structural vibration energy experimently, and then, some knowledge for dynamic structural design is obtained.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2012년도 추계학술대회 논문집
• /
• pp.667-668
• /
• 2012

• Composites Research
• /
• 제29권4호
• /
• pp.203-208
• /
• 2016

금속/고분자 샌드위치 복합재는 경량성과 제진, 방음 등의 다기능성의 측면에서 기존의 스틸 강판을 대체할 후보 중 하나로서 연구되고 있다. 금속/고분자 복합재의 활용하기 위해서는 접착력을 바탕으로 한 박리 거동 예측이 매우 중요한 요소이다. 본 연구에서는 응집요소를 사용하여 유한요소 해석을 통해 접착제를 사용한 고분자 테이프의 박리거동 해석을 수행하였다. 응집요소의 특성은 박리시험과 역학 관계로부터 도출한 파괴인성을 통해 정의하였고 이를 해석에 적용하였다. 스틸 강판에서 고분자 테이프를 박리하는 시험을 모사하였고, 해석결과와 시험결과를 비교하여 박리 거동 모사가 가능함을 확인하였다.