• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.1
• /
• pp.345-350
• /
• 2017

Downsizing is widely applied to diesel engines in order to improve fuel efficiency and reduce exhaust emissions. Engine sizes are becoming smaller but pressure and temperature inside combustion chambers are increasing. Therefore, research for fuel spray under high pressure and temperature conditions is important. A constant volume chamber which simulates high temperature and pressure likely to be found in diesel engines was developed in this study. Pressure and temperature were increased abruptly because of ignition of the pre-mixture in the constant volume chamber. Then pressure and temperature were gradually decreased due to the heat loss through the chamber wall. Fuel spray occurred when temperature and pressure were reached at the target condition. In this experiment, the temperature condition should be exactly defined to understand the relation between fuel evaporation and ambient temperature. A fast response thermocouple was developed and used to measure the temporal and spatial temperature distribution during the combustion process inside the combustion chamber. In the results, the core temperature was slightly higher than the bulk temperature calculated by the gas equation. Ed-note: do you want to say 'ideal gas equation'? This was attributed to the heat transfer loss through the chamber wall. The vertical temperature deviation was higher than the horizontal temperature deviation by 5% which resulted from the buoyancy effect.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.3
• /
• pp.48-57
• /
• 2003

A cylindrical constant volume combustion chamber was used to investigate the flow characteristics at spark plug and the combustion characteristics of homogeneous charge methane-air mixture under various initial pressure, excess air ratio and ignition times in quiescent mixture. The flow characteristics such as mean velocity and turbulence intensity was analyzed by hot wire anemometer. Combustion pressure development measured by piezoelectric pressure transducer and flame propagation acquired by ICCD camera were used to investigate the effect of initial pressure, excess air ratio and ignition times on pressure, combustion duration, flame speed and burning velocity. Mean velocity and turbulence intensity had the maximum value at 200 or 300ms and then decreased to near 0 value gradually after 3 seconds. Combustion duration, flame speed and burning velocity were observed to be promoted with excess air ratio of 1.1, lower initial pressure and ignition time of 300ms.

• Journal of Advanced Marine Engineering and Technology
• /
• v.21 no.3
• /
• pp.302-310
• /
• 1997

In this paper, we find a method to improve ignitability using methanol which is prospective as an alternative fuel. The constant volume combuster is divided into main chamber and sub-cham¬ber. These two chambers are linked by an adapter which is shaped like a cup. We also compare CDI to HIS that is revised in our laboratory for making a scrutiny into the effects of ignition char¬acteristics. Besides, we analyze a flame propagation process in the main and sub-chamber through taking pictures 10, 000 frames per second by high speed camera at the state being fabricated quartz glass aside main and sub-chamber.

• Proceedings of the KAIS Fall Conference
• /
• 2007.05a
• /
• pp.239-241
• /
• 2007

본 논문에서는 CNG 연료를 고압분사시 연소 특성에 관한 데이터를 확보하고자 한다. 실험은 연소실내의 분사압력과 점화시간을 다양하게 할 수 있는 정적연소상태에서 이루어졌다. 광학적인 실험장치가 연소 특성을 파악하기위해서 공학적인 실험장치가 이용되었다. 이러한 연구는 차후 CNG를 고압연소분사시 형성되는 연소특성에 대한 중요한 기초적인 자료가 될 것이다.

• Journal of Energy Engineering
• /
• v.4 no.1
• /
• pp.85-94
• /
• 1995

본 연구에서는 최근 차량용 대체연료로서 주목받고 있는 천연가스의 연소특성을 규명하기 위해 밀폐된 정적연소실을 이용, 당량비, 초기압력 및 점화위치 변화에 따른 연소실험을 행하였으며, 그 결과 다음과 같은 결론을 얻었다. 메탄-공기 예혼합기의 화염전파과정은 이론혼합기 부근에서 구면형으로 진행되는데 반해, 과농 또는 과박 혼합기 그리고 점화위치가 연소실 벽면에 가까울수록 타원형으로 진행되며, 초기압력이 증가함에 따라 화염전파는 느려진다. 화염전파속도와 연소 속도는 초기압력이 낮고 점화위치가 연소실 중심에 가까울수록 빠르며, 당량비 1.0∼1.1 사이에서 최대치를 보인다.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.7
• /
• pp.1398-1407
• /
• 1992

The prediction of heat loss during laminar flame propagation was carried out by measurement of gas pressure and visualization of flame propagation in the constant volume combustion chamber. And to validate the prediction, the instantaneous temperature at wall of combustion chamber was also measured. Consequently, it was found that heat loss was increased according to increasing of maximum flame travel distance, but rate of heat loss for heat release during laminar flame propagation was nearly constant. And heat loss depends on heat transfer area which was contacted the wall by burned gas regardless to spark plug location.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.3
• /
• pp.10-18
• /
• 2004

It is well known that the stratified charge combustion has many kind of advantages to combustion characteristics, such as higher thermal efficiency and less CO, NOx levels than conventional homogeneous mixture combustion. Although this combustion can be caused low fuel consumption, it is produced the high unburned hydrocarbon and soot levels because of different equivalence ratio in the combustion chamber. Moreover it has a lot of possibility of low output and misfire if the mixture gas would not be in existence around the spark plug. In this paper, fundamental studies for stratified combustion were carried out using a constant volume combustion chamber. The effect of locally mixture gas distribution according to control the direct injection and premixed injection in the chamber were examined experimentally. In addition, the effects of turbulence on stratified charge combustion process were observed by schlieren photography.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.3
• /
• pp.19-26
• /
• 2004

A prior fundamental study was executed using a constant volume chamber to improve the burning properties of lean pre-mixture by the injection of active radicals generated in the sub-chamber. In consequence, RI method shows remarkable progress in the aspects of burning velocity and combustible lean limit compared with SI method. In this study, the necessary additional works have been performed to be based on the former results. We changed parameters as the initial temperature and the initial pressure of mixture. And the effects of residual gas at issue in a real engine were investigated. As a result, the effects of initial temperature were significant, but on the other hand, those of initial pressure were slight. The correlation of passage hole number between overall passage hole area was grasped. And the more detailed analysis is required on residual gas.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.4
• /
• pp.201-209
• /
• 1996

This study describes the combustion characteristics of methance-air mixture with various equivalence retio and initial conditions of mixture in constant volume combustion chamber. Combustion characteristics of methane-air mixture such as combustion pressure, combustion temperature, and heat release were investigated by the measurement of combustion pressure and temperature in the combustion chamber. The results show that maximum combustion pressure, gas temperature and rate of heat release have peaks at equivalence ratio of 1.1. Combustion duration is also the shortest at the equivalence ratio of 1.1 and it is shortened as initial mixture temperature increases.

• Journal of the Korean Society of Combustion
• /
• v.6 no.1
• /
• pp.14-19
• /
• 2001

Interests and importance of down-scale combustor is increasing with the emerging need for miniaturized power source which is now a bottleneck of micro system development. But in down scaled combustor increased heat loss compared to thermal energy generation inhibits the usability and application of the device, so as a preliminary work of down scaled combustor fabrication. Modeling tool for the device should be established, in this study modeling approach of closed vessel combustion phenomena that can express heat loss effect and resulting quenching is proposed and the result is compared with experiment data. From this model heat loss effect following combustor scale down can be further understood, and further more design parameter and analysis tool can be obtained.