• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.27 no.6
• /
• pp.685-692
• /
• 2003

A numerical simulation of flame propagation in a micro combustor was carried out. Combustor has a sub -millimeter depth cylindrical internal volume and axisymmetric one-dimensional was used to simplify the geometry. Semi-empirical heat transfer model was used to account for the heat loss to the walls during the flame propagation. A detailed chemical kinetics model of $H_2/Air$ with 10 species and 16 reaction steps was used to calculate the combustion. An operator-splitting PISO scheme that is non-iterative, time-dependent, and implicit was used to solve the system of transport equations. The computation was validated for adiabatic flame propagation and showed good agreement with existing results of adiabatic flame propagation. A full simulation including the heat loss model was carried out and results were compared with measurements made at corresponding test conditions. The heat loss that adds its significance at smaller value of combust or height obviously affected the flame propagation speed as final temperature of the burnt gas inside the combustor. Also, the distribution of gas properties such as temperature and species concentration showed wide variation inside the combustor, which affected the evaluation of total work available of the gases.

• Journal of Labour Economics
• /
• v.36 no.1
• /
• pp.1-44
• /
• 2013

This paper surveys the existing literatures on labor demand of Korea. It has been found that labor and capital are substitutes in Korea and the result holds even if labor is decomposed into white collar and blue collar workers. The elasticity of substitution lies between 0 and 1. It is yet unclear if employment and work hours are substitutes. The reduction of legal work week did not increase employment although decreased work hours. The labor demand elasticity is below 0.5 in the short run. Since mid 1990s, the technological change has shown skill bias and therefore increased demand for skilled labor.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.25 no.10
• /
• pp.1311-1317
• /
• 2001

To investigate only the effects of the stratified mixture distribution on initial flame propagation and combustion characteristics, the instantaneous equivalence ratio in the spark plug gap and combustion pressure were measured simultaneously In a constant volume chamber, To induce the stratified propane-air mixture distribution near the spark plug, counter-flow typed mixture injection system was used under the constant mean equivalence ratio $\Phi$$\_$mean/= 1.0 The instantaneous equivalence ratio was measured by a single-shot Raman scattering with narrow-band KrF excimer laser. The measuring error was within the limit of $\pm$ 3.5% provided that the proposed method was applied to the measured Raman signals. Judging from mass fraction burned derived from the measured pressure, the optimum combustion characteristics were shown under the condition that the local equivalence ratio in the spark plug was near 1.28$\pm$0.04, and these characteristics were more remarkable at the initial stage of combustion.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.16 no.1
• /
• pp.87-94
• /
• 2003

A geometric non-linear finite element formulation of CRTS reflector subjected to displacement loads, corresponding to the successional assembly steps of the reflector, is presented in order to determine the initial static equilibrium state based on the displacement incremental method. Parametric analyses of the influence of cables and mechanical properties of the reflector on the shape error between reference and equilibrium surfaces have been studied. These results of the present study are compared with the others using Galerkin mothod and NASS 98 program to demonstrate the feasibility.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.4 no.3
• /
• pp.19-28
• /
• 2000

In general the data such as thrust, pressure, temperature and combustion time are measured in developing the propulsion system of solid rocket motor through static firing test. But in the case of personal surface to air missile there are required a severe safety specifications in order to eliminate gunner hazard from the exhaust plume of motors. The safety requirements lead to the design of separation device and safety igniter device. The dynamic firing test for the designed two devices should be conducted under the flight environmental conditions to verify the requirements compliance. In this study the technique for dynamic firing test of propulsion system of personal surface to air missile is proposed and the method to design the dynamic test bench is also studied.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2018.05a
• /
• pp.541-542
• /
• 2018

CAE 와 같은 고충실도 대용량 엔지니어링 데이터의 시공간 정밀 분석검증을 위해서는 고해상도 몰입형 가시화 기술과 더불어 이를 직관적이고 효율적으로 제어하기 위한 휴먼 인터페이스 기술이 중요하다. 최근 대중화에 근접한 HMD 기기 및 컨트롤러를 이용한 응용 연구가 발표되고 있고, 이를 통해 엔지니어 위주의 정적 분석환경을 벗어나, 설계/해석/운용 전문가들의 동적 협업분석 환경 제공이 가능한 몰입형 가시화 환경 및 휴먼 인터페이스 기술이 적용되고 있다. 하지만 CAE 해석지원을 위한 대화면 몰입형 가시화 환경에서 사용가능한 직관적 인터페이스기술에 대한 연구는 미진한 상황이다. 본 연구에서는 신체의 자연스러운 움직임으로 가상현실을 탐색하고 데이터 조작을 구현할 수 있는 몰입형 가시화 전용의 휴먼 인터페이스 및 연동기술에 대한 연구과정을 소개한다.

• Journal of Bio-Environment Control
• /
• v.26 no.4
• /
• pp.402-410
• /
• 2017

The effect of the steel pipe member joint on the design performance of a plastic multi-span greenhouse was analysed through the comparing full-scale experiment and numerical analysis. The design performance of the greenhouse is generally evaluated through numerical analysis, but it is rare to consider the characteristics of the connections or joints of the members. In this study, the effect of the column-gutter beam-rafter-wind break wall joint on the design performance of the whole structure of a plastic multi-span greenhouse was analysed. The numerical results with assuming that the member joint are rigid condition were compared with the full-scale load test results using member joints used in the field. The stiffness of the entire structure was compared using the load-displacement relationship and the change of the load sharing ratio that the main members such as column, rafters, and wind break wall was analysed. The results of the load test were about 40% larger than the numerical result and the member stress was more than twice as large as those of the loaded columns. In order to increase the reliability of the design performance of the greenhouse, it is necessary to develop a numerical analysis model which can consider the characteristics of various joints.

• Journal of Korean Home Economics Education Association
• /
• v.18 no.3 s.41
• /
• pp.81-95
• /
• 2006

The purpose of this study was to evaluate appropriateness of clothing & textiles as educational contents in practical arts or technology home economics in the 7th curriculum. The factors of appropriateness were the amounts of learning, the degrees of understanding, interest and requirement on the educational content recognized by elementary, middle and high school students. The data collected from evaluation sheets were analyzed by frequency analysis, t-test, crossing analysis using SPSSWIN 12.0 program. Results were as follows; First. more than 50% of elementary, middle and high school students were recognized the amounts of tearing of clothing & textiles proper. But boy students of middle school recognized 'making clothes' in practice course too heavy. Second. It were from easy to difficult that the degrees of understanding on the educational contents of clothing & textiles recognized by elementary school students. Elementary school students understood both 'making cushion' and 'sewing machine theory and practice' difficult. Middle school students understood 'basic sewing for repairing clothes' and 'making clothes' difficult whereas high school students thought 'making pillow' and 'making bag' difficult. All students understood practice courses hard. Third, the degrees of interest showed from 'interest' level to 'not interest' level in case of elementary school students whereas 'interest' level in middle school students and 'common' in high school students. Fourth, the requirements of elementary, middle and high school students were in 'necessary' level to 'common' level. Editional contents such as 'learning sewing machine', 'making cushions'. 'making clothes', and 'making pillow-cover and bag' were low in the degrees of requirement. The correlationship between the amount of learning and the each level of understand, interest and requirement of students was indirect. On the other hand, Among the level of understand, interest and requirement were direct in case of high school students.

• Journal of Korean Home Economics Education Association
• /
• v.19 no.1 s.43
• /
• pp.35-45
• /
• 2007

The purpose of this study was to examine the influence of make-up attitude, self-esteem and body satisfaction on clothing behavior. The data was collected from 356 female college students in Seoul. For data analysis, reliability analysis, factor analysis, correlation analysis, stepwise multiple regression and t-test were used. The results of this study were as follows: 1) Five factors of make-up attitude were identified: pursuit of confidence, aesthetics, sociality, fashion and attractiveness. 2) Five factors of make-up attitude had Positive correlation related to clothing behavior i. e. aesthetics, exhibition, dependence and sexual attractiveness. 3) The aesthetics and dependence of clothing were influenced by pursuit of confidence, aesthetics, sociality and fashion. The exhibition of clothing was influenced by pursuit of confidence, pursuit of aesthetics and self-esteem. The sexual attractiveness of clothing was influenced by self-esteem, pursuit of aesthetics, attractiveness and fashion. 4) There was significant difference between the group of high self-esteem and low self-esteem on aesthetics and sexual attractiveness of clothing. 5) There was significant difference between the group of high body satisfaction and low body satisfaction on sexual attractiveness of clothing.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.32 no.2A
• /
• pp.65-73
• /
• 2012

In this study, we tested structural performance of Half-Decked PSC girder which was developed for applying to long span bridge. We operated 4 point bending test with 60 m span full scale girder designed as simple bridge with hinge-roller boundary condition. Actuators were set on the both sides of girder, 5.5 m away from the center, and 4 stages of cyclic loading was applied at rate of 1 kN/sec. Through stages 1 to 4, loading and unloading 1,000 kN, 1,200 kN, 1,500 kN, and 2,000 kN were repeated and displacement, strain of concrete and steel, crack of girder were checked. From these results, the strength of girder was assessed and resilience and ductility were observed after removing the load. Since initial flexural crack occurred in the vicinity of 1,400 kN, non-linearity of load-displacement curve appeared and definite residual strain was measured at that point. The test result showed that initial cracking load was over twice the DB-24 load which means the developed girder had sufficient strength. To verify the experimental results, we numerically analyze the test and confirmed that the data were similar with results from the test above. Half-Decked PSC type of 60 m-girder developed in this study showed its adequate structural capacity through static loading test, which proved that possibility of applying the girder to actual bridges practically.