• 한국추진공학회지
• /
• 제13권6호
• /
• pp.34-40
• /
• 2009

본 논문은 액체로켓엔진의 구성품인 연소기와 가스발생기의 연소 안정성 평가를 위한 평가 방법과 기준에 관해 서술하였다. 두 가지 평가 방법이 있는데, 첫 번째는 일반적인 정상 연소 시험을 통해 연소 안정성 여부를 판단하는 통계적인 접근 방식을 취하는 정적 평가와 두 번째로는 연소장에 압력 교란을 일으키는 장치를 이용, 생성된 펄스의 감쇠 특성을 파악하는 동적 평가가 있다. 누적된 실제 추진제 연소 시험 결과를 통해서 정적 평가의 안정성 여부는 Root-Mean-Square 값이 연소실 압력의 3%, 동적 안정성 여부는 가진된 압력 섭동의 감쇠시간이 10 msec로 기준을 설정하였다.

• 한국자동차공학회논문집
• /
• 제12권2호
• /
• pp.45-53
• /
• 2004

An experimental study was carried out to obtain the fundamental data about the effects of radicals induced injection on premixture combustion. A constant volume combustor divided to the sub-chamber and the main chamber was used. The volume of the sub-chamber is set up to occupy less than 1.5％ of that of whole combustion chamber. Radial twelve narrow passage holes are arranged between the main chamber and the sub-chamber. The products including radicals generated by spark ignition in the sub-chamber will derive the simultaneous multi-point ignition in the main chamber. While the equivalence ratio of pre-mixture in the main chamber and the sub-chamber is uniform. We have examined the effects of the sub-chamber volume, the diameter of passage hole, and the equivalence ratio on the combustion characteristics by means of burning pressure measurement and flame visualization. In the case of radical ignition method(RI), the overall turning time including the ignition delay became very short and the maximum burning pressure was slightly increased in comparison with those of the conventional spark ignition method(SI), that is, single chamber combustion without the sub-chamber. The combustible lean limit by RI method is extended to more ER=0.25 than that by SI method. Therefore the decrease of every emission including NOx and the improvement of fuel consumption is anticipated due to lean burn.

• 한국분무공학회지
• /
• 제15권3호
• /
• pp.150-156
• /
• 2010

Ethanol has properties of a lower setting point, higher oxygen contents, lower cetane numbers, and also higher volatility compared to biodiesel. Thus, biodiesel fuel can be improved in the fluidity of blending fuel and exhaust emissions by blended ethanol fuel. This research aims to understand combustion characteristics of biodiesel-ethanol blending fuel inside a constant volume chamber. High speed camera was applied to visualize the physics of development of combustion processes, and combustion pressure and exhaust emissions were measured at several blending ratios of ethanol and biodiesel fuel. This information may contribute to improve the performance of biodiesel engine and reduce emissions in future.

• Journal of Advanced Marine Engineering and Technology
• /
• 제29권2호
• /
• pp.154-160
• /
• 2005

The result of combustion experiment by using the methanol-gasoline blended fuel showed that the supplying pressure appeared the maximum pressure between equivalent rate 1.1 and 1.2. and the evaporation of the fuel has been known to have been greatly influenced by surrounding temperature and the combustion chamber temperature after being injected from the injector And it is confirmed that the rate of evaporation had been suddenly dropped according to the temperature in the combustion chamber though the injected foe) had been fully evaporated Such tendency has visibly appeared when the zone is leaner. and we recognize that the rich fuel supply is needed in the operation of cold operating.

• 한국자동차공학회논문집
• /
• 제12권2호
• /
• pp.1-8
• /
• 2004

A cylindrical constant volume combustion chamber was used to investigate the exhaust emission characteristics of homogeneous charge, stratified pattern and inhomogeneous charge under various conditions using gas chromatography. In the case of homogeneous charge condition, the $CO_2$ concentration is proportional to excess air ratio and overall charge pressure, the $CO_2$ concentration is proportional to excess air ratio and the UHC concentration is inversely proportional to ignition time and overall charge pressure. In the case of stratified pattern, the RI(rich injection) condition shows better exhaust emission characteristics, especially $CO_2$, than that of HI (homogeneous injection) or LI (lean injection) conditions. In inhomogeneous charge conditions, when initial charge pressure is increased, $CO_2$ and UHC concentration is reduced but $O_2$ concentration is increased. And when the excess air ratio of initial charge mixture is 3.0, UHC and $CO_2$concentration show lowest values.

• 한국분무공학회지
• /
• 제10권2호
• /
• pp.41-47
• /
• 2005

Exhaust gas emissions from internal combustion engines are one of the major sources of air pollution. And. it is extremely difficult to increase gasoline engine efficiency and to reduce NOx and PM(particulate matter) simultaneously in diesel combustion. This paper offers some basic concepts to overcome the above problems. To solve the problems, a recommended technique is CAI(controlled auto-ignition) combustion. In this paper. internal EGR(exhaust gas recirculation) effect is suggested to realize CAI combustion. An experimental study was carried out to achieve CAI combustion using homogeneous premixed gas mixture in the constant volume combustion chamber(CVCC). A flame trap was used to simulate internal EGR effect and to increase flame propagation speed in the CVCC. Flame propagation photos and pressure signals were acquired to verify internal EGR effect. Flame trap creates high speed burned gas jet. It achieves higher flame propagation speed due to the effect of geometry and burned gas jet.

• 에너지공학
• /
• 제12권2호
• /
• pp.124-130
• /
• 2003

본 연구에서는 정적연소실을 이용하여 차량용 대체연료로써 메탄 및 수소첨가 메탄의 연소특성을 수소첨가율, 점화위치 및 점화방법에 따라 고찰하였다. 그 결과 연소효율, 최고연소압력 등과 같은 연소특성을 악화시키지 않고 희박 혼합기 조건하에서도 MSCDI 장치 사용에 의해 전 연소시간과 NO 농도를 저감시킬 수 있었다. 또한, 수소를 천연가스의 주 성분인 메탄에 혼합함에 따라 전 연소시간은 순수 메탄만을 사용할 때에 비해 단축되었으며, 이와 동시에 연소촉진율도 순수 메탄만을 사용하였을 때에 비해 상당히 향상되었다.

• 한국자동차공학회논문집
• /
• 제9권4호
• /
• pp.103-111
• /
• 2001

In the present study, the internal combustion engine tends to high performance, fuel economy, small-sized. Therefore, it is necessary to solve the problems on thermal load, abnormal combustion, etc in the engine. Thin film instantaneous temperature probe was made, and the measuring system was established. The instantaneous surface temperatures in the constant volume combustion chamber were measured with this system and the heat flux was obtained by Fourier analysis. Maximum instantaneous temperatures were obtained after 55∼60ms from ignition and they increased as equivalence ratio and varied differently as the position of probe. Total heat loss during combustion time was affected by the equivalence ratio and differed widely as the position of probe.

• 한국자동차공학회논문집
• /
• 제3권2호
• /
• pp.136-145
• /
• 1995

The aim of this study is to gain a better understanding of the effect of a flow motion on the flame development by means of an optically-accessible constant-volume combustion chamber and the visualization technique of a combustion flame. At first, the characteristics of a flame propagation are investigated in the combustion field of the two kinds of flow conditions such as a quiescent and a flowing condition, and methane-air mixture is used as fuel. Then the same investigation is performed in two flow configurations : bulk flow motion type and turbulence generating type. In this study, the combustion phenomena are analyzed by measuring the combustion pressure, flame propagation speed, mean velocity, turbulent intensity, and mass fraction burned.

• 한국연소학회지
• /
• 제13권3호
• /
• pp.9-16
• /
• 2008

In this study, a cylindrical constant volume combustion chamber is used to investigate the flow and combustion characteristics of methane-air homogeneous mixture under various initial charge pressure, excess air ratios and ignition times. The flame and burning speed, mean gas speed are calculated by numerical analysis to analyze the combustion characteristics. It is found that the mean gas velocity during combustion has the maximum value around 300 ms and then decreased gradually on the condition of 10000 ms, and that the combustion duration is shorten and flame speed and burning velocity have the highest value under the conditions of an excess air ratio 1.1, an initial charge pressure of 0.2 MPa and an ignition time of 300 ms in the present study. And, the initial pressure and burning speed are in inverse proportion, so that it is in agreement with Strehlow who presented that the initial pressure and burning speed are in inverse proportion when the burning speed is under 50cm/s.