• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.9 s.100
• /
• pp.926-931
• /
• 2005

In this paper, the printed-sleeve monopole antenna which has the small size and the broadband characteristics, is presented and its radiation characteristics are investigated. To conform the broadband characteristics of the proposed antenna, the experimental antenna is designed, fabricated, and its radiation characteristics are measured in PCS band (1.75 GHz${\~}$1.87 GHz). It is shown that the designed antenna has the non-directional pattern in the horizontal plane, the directional pattern in the vertical plane, VSWR less than 1.5, and gain in 2.14 dBi${\~}$3.4 dBi. From these results, the proposed antenna is conformed as a broadband antenna which can be used for the mobile communication indoor antenna extensively.

• Journal of Advanced Marine Engineering and Technology
• /
• v.32 no.8
• /
• pp.1263-1268
• /
• 2008

In this paper, the low noise power amplifier for GaAs FET ATF-10136 is designed and fabricated with active bias circuit and self bias circuit. To supply most suitable voltage and current, active bias circuit is designed. Active biasing offers the advantage that variations in the pinch-off voltage($V_p$) and saturated drain current($I_{DSS}$) will not necessitate a change in either the source or drain resistor value for a given bias condition. The active bias network automatically sets a gate-source voltage($V_{gs}$) for the desired drain voltage and drain current. Using resistive decoupling circuits, a signal at low frequency is dissipated by a resistor. This design method increases the stability of the LNA, suitable for input stage matching and gate source bias. The LNA is fabricated on FR-4 substrate with active and self bias circuit, and integrated in aluminum housing. As a results, the characteristics of the active and self bias circuit LNA implemented more than 13 dB and 14 dB in gain, lower than 1 dB and 1.1 dB in noise figure, 1.7 and 1.8 input VSWR at normalized frequency $1.4{\sim}1.6$, respectively.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.6 no.2
• /
• pp.119-125
• /
• 2007

In this paper, a multi-band folded planar monopole internal antenna for mobile handset applications is proposed. The proposed antenna has multi-resonances, which is different from a conventional folded monopole antenna, and it provides a wide bandwidth at high frequency bands. The measured impedance bandwidth (VSWR < 3) is 180 MHz and 1880 MHz in lower and higher frequency bands, respectively. The proposed antenna can effectively cover most wireless communication bands including CDMA, GSM, GPS, DCS, PCS, and W-CDMA, WiBro and S-DMB.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.6 no.2
• /
• pp.113-118
• /
• 2007

KPCS internal antenna in this paper, is designed and fabricated using the theory based on the folded monopole antenna. I propose folded monopole internal antenna which has high gain low profile structure with easy installation into the handset of mobile phone. Design frequency is 1.8 GHz that is a center frequency of Korea PCS frequency band, and the impedance variances due to change of antenna structure as a length and width are simulated. Measurements show that input VSWR range under 2:1 is 1.72 - 1.88 GHz, and radiated H-plane pattern is omnidirectional under passive state. Active sensitivities and output power of phone applied antenna are $-105\;{\sim}\;-108\;dBm$ and $22.5\;{\sim}\;23.6\;dBm$ max., respectively.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.7
• /
• pp.603-607
• /
• 2009

In this paper, a GPS antenna is designed by using metal film which can be attached on the case of battery without additional space for antenna in GPS band operation. The proposed metal film has a half-wavelength slot radiator. The slot radiator is fed by th electromagnetic field coupled from the GSM850/PCS band antenna. The proposed GPS antenna obtains about 20 MHz bandwidth(VSWR<3) which can cover entire GPS band. The antenna has an average gain of -3.8 dBi.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.6
• /
• pp.94-101
• /
• 2007

This paper, we analyzed that the measured data of the radiated power spectrum of electromagnetic waves and the standing wave ratio(SWR) of the spark plug cable and spark plug. The measured data are the power strength of the electromagnetic waves radiated from the spark ignition system, the measured frequency ranges are 110 to 610MHz. The results show that the strength of radiated power spectrum and bandwidth have relation to the SWR of the the spark plug cable and spark plug, and the SWR of them is different because of the characteristics of resistor at the spark plug is different with the manufacturers. From the analyzed results, it can be concluded that the less SWR is little, the less maximum level of power spectrum is weak and bandwidth above the reference level is small.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.3
• /
• pp.260-267
• /
• 2003

The wideband characteristics of planar antennas with a wide radiating slot have been examined in this paper. A various resonance modes are generated in the wide slot and the wideband characteristics are enhanced by impedance match at each resonance frequencies. In this process, the geometry effects on the impedance match were extracted and it was found that a round corner rectangular slot antenna has more stable impedance match over a wide frequency range than a normal rectangular slot antenna. The round corner rectangular slot antenna is fabricated to verify the wideband characteristics and its measured bandwidth is almost 2 octaves(2.08 ㎓~8.25 ㎓) with VSWR$\leq$2.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.6
• /
• pp.550-557
• /
• 2003

In this paper, two dualband internal antennas for GPS/PCS handset are proposed. At first, the monopole antenna with parasitic dipole element is designed to print PCB of handset directly. At second, the antenna with bended loop structure is designed to bend to use internal space of handset maximumly. The proposed dualband internal antennas provide a 2:1 VSWR bandwidth of over 19.1 % which are possible to cover two bands at once. the antennas have a gain between -0.4 and 3.33 ㏈i at all bands and they have almost omni-directional patterns.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.4 no.1
• /
• pp.124-136
• /
• 2001

In this paper, we designed and manufactured the Ku-band circular waveguide antenna to do wireless communication with a ground radar as on-board antenna of missile. Using the MATLAB and the HFSS, we designed the circular polarizer which has a characteristic of circular polarization and broadband using the capacitive pin method, the feeder to feed coaxial line to circular waveguide, and a stopper to prevent a conductor material from being inserted. Then we simulated the designed antenna using the HFSS, obtained the gain and the radiation pattern. Because of a difficulty of manufacture, we established a manufacture process procedure. Antenna is manufactured with this procedure, test results of the manufactured antenna are the axial ratio of 1.37 ~ 1.72, the 3 ㏈ beamwidth of $72.23^{\circ}{\sim}78.54^{\circ},$ and the gain of 3.26 ~ 4.61 ㏈ within frequency band. We knew that these results are similar with simulation results. Also, we confirmed that the manufactured antenna is satisfied with requirement conditions through performance test, environmental test and flight test.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.3 no.2
• /
• pp.339-346
• /
• 1999

A RF receiver section for INMARSAT-C external mounting unit was designed, fabricated and evaluated. Using a INA-03184, the high gain amplifier consists of matched amplifier type. Active bias circuitry can be used to provide temperature stability without requiring the large voltage drop or relatively high-dissipated power needed with a bias stabilization resistor. The bandpass filter was used to reduce a spurious level. As a result, the characteristics of the receiver section implemented here show 60 dB in gain, 44.83 dBc in a spurious level. The voltage standing wave ratios(VSWR)of input output port are less than 1.8:1, respectively.