• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2001년도 유체기계 연구개발 발표회 논문집
• /
• pp.99-105
• /
• 2001

In this study, the instability of a centrifugal compressor with vaned diffuser was investigated. During unstable operation of the test compressor, pressure fluctuations at different diffuser radius ratios were measured by using high frequency pressure transducers. Two different types of stall, mild and deep stall, were observed alternately and irregularly at some flow rate where the compressor performance was steeply deteriorated. In this transient zone, the size of rotating stall cell was estimated through the Wavelet transform analysis. It was about 45 percents of rotor circumferential space at 3000 rpm and not dependent on flow rate.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2010년 춘계학술대회논문집
• /
• pp.136-141
• /
• 2010

This study describes effects of width contraction in vaneless diffuser on the performance of centrifugal compressors using commercial CFD code. Numerical analysis for three different diffusers such as Parallel, half contraction, and full contraction was performed. The results show that the performance of the centrifugal compressor is improved through the use of the diffusers with width parallel in high flow rate. The width contraction of diffusers is influenced static pressure rises. Comparison with the experimental data shows agreement.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.743-747
• /
• 1997

Polishing work for a curved surface die demands simple and repetitive operations and requires much time while it also demands high precision. Therefore it is operated by skilled worker in handiwork. Howener workers avoid polishing work gradually because of the poor environments such as dust and noise. In order to reduce the polishing time and to alleviate the problem of shortage of skilled workers, researches for automation of polishing have been pursued in the developed countries. In the research, a polishing robot with 2 degrees of freedom motion attached to machining center with 3 degrees of freedom and pneumatic system forms an automatic polishing system which keeps the polishing tool vertically on the surface of die and maintains constant pneumatic pressure. A synchronization between machining center and polishing robot is accomplished by using M code of machining center. A rulled surface and shadow mask are polished by the developed polishing robot.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2005년도 연구개발 발표회 논문집
• /
• pp.367-372
• /
• 2005

This study primarily is concerned with a new device which has been developed following the international standards to measure the ventilation performance at elevated temperature. This device can measure duration of ventilation, performance of electricity, static pressure at elevated temperature and also it is having provision to measure reversible performances during fire hazards. Invented device is closed circuit type system which is best suited for korean industrial environment with low cost and high efficiency. International standards has been compared and performance testing has been major using BS 7346 which is tested by Warrington Fire Research Centre.

• 설비공학논문집
• /
• 제27권1호
• /
• pp.44-49
• /
• 2015

Ceiling cooling and heating system that consider load arrangement and space in the ceiling needs to be developed. Therefore, experimental and economic changes were done to verify the performance of compact type VAV. The test results were as follow. 1) Noise test result, measuring approximately 50.4 dB~56.6 dB (before ceiling in landfill), had a better ceiling deadline than the current measure, about a 10 dB noise reduction, so that the office baseline (40~50 dB) noise was judged to be less than test. 2) For the static pressure test result, taking out an outside hydrostatic 25 mmAq, 24.8 mmAq was measured, respectively, at the point. 3) For the life-cycle cost analysis result, the initial investment cost, maintenance replacement costs, and maintenance costs increased 0.2%, but the energy savings ratio was 19.5% while the whole life cycle savings of 40 years LCC was reduced 11.9%.

• 한국추진공학회지
• /
• 제3권1호
• /
• pp.65-71
• /
• 1999

마하수 2.5인 모델 스크램제트 연소기내에서 초음속 수소-공기 화염에 대한 충격파의 영향을 실험적으로 연구하였다. 본 실험은 충격파가 초음속 화염에 미치는 영향을 연구한 최초의 실험연구이다. 동일한 모양과 크기의 $10^{\cire}$ 쐐기를 연소기 팽창 벽면에 각각 부착시켜 평면경사충격파를 발생시켰고 충격파가 화염에 미치는 영향을 연구하였다. 쉬릴렌 가시화 사진과 벽면정압, 그리고 두개의 다른 공기온도에서의 연소효율을 측정하였으며, 충격파가 없는 경우와 비교하였다. 충격파에 의해서 화염 모양은 크게 변화하였다. 연소효율은 공기온도에 따라 상이한 결과를 보였는데 공기정체온도가 증가하고 연료유량이 증가한 경우에 충격파에 의한 연소효율은 더 좋은 결과를 보였다.

• 대한기계학회논문집A
• /
• 제28권7호
• /
• pp.896-903
• /
• 2004

This paper proposes the structural characteristic analysis and evaluation on the hydrostatic guide way and feeding system of a high-precision centerless grinder for machining ferrules. In order to realize the required accuracy of ferrules with sub-micron order, the axial stiffness and motion accuracy of feeding system have to become higher level than those of existing centerless grinders. Under these points of view, the physical prototype of feeding system composed of steel bed, hydrostatic guide way and ballscrew feeding mechanism is designed and manufactured for trial. Experimental results show that the axial and vertical stiffnesses of the physical prototype are very low as compared with those design values. In this paper, to reveal the cause of these stiffness difference, the structural deformations on the virtual prototype of feeding system are analyzed based on the finite element method under experimental conditions. The simulated results illustrate that the deformation of front ballscrew support-bearing bracket is the main cause of reduction in the axial stiffness of feeding system, and the deflection of bed structure and the bending deformation of hydrostatic guide rails are the main causes of reduction in the vertical stiffness of feeding system.

• 한국기계연구소 소보
• /
• 통권18호
• /
• pp.75-85
• /
• 1988

유압 펌프 또는 모터, 특히 레이디얼피스톤형 모터, 용 분배기는 동적인 평형상태를 유지하기 위해 양면이 완전히 똑같이 가공된 회전부재와 이 부재의 양면에 동적평형을 보조할 수 있도록 표면에 가공된 형상이 동일한 2개의 고정부재와 이 2개의 고정부재의 간격유지를 위하여 회전부재주위에 사각의 단면적을 갖는 원형링으로 이루어져 있다. 회전부재는 기본적으로 밸브부를 가지고 있으며 평형상태를 보조하기위해 밸브부의 외주에 정압베어링을 설치할 수도 있다. 2개의 고정 부재중 1개는 몇 개의 단이 있는 부재인데 이는 압력상승에 의한 볼트의 인장을 보상하기 위해 밸브케이싱과 축방향의 이동이 가능하도록 하기 위한 방법이다.

• 한국유체기계학회 논문집
• /
• 제15권6호
• /
• pp.51-57
• /
• 2012

Performance evaluation of a compressor is conducted to develop 500W class ultra-micro gas turbine (UMGT) for power generation. The performance evaluation is essential to check the performance of the components of UMGT, a radial turbine, a centrifugal compressor, an angular combustor and a shaft, which have been already designed in previous researches. The purpose of this study is to introduce the development process of the performance testing equipments of the UMGT and to present the results of compressor performance test. For the performance evaluation of the compressor, two test equipments are developed and the initial test equipment uses commercial static air bearings with long shaft. In the improved test equipment, static air bearing is improved to increase rotating speed and compressed nitrogen gas is used for utility gas of the static air bearing to supply compressed air in a stable and steady way. To increase rotating speed to 320,000 rpm, 80% speed of design speed, compressed air is provided to the turbine. The performance map of the compressor with the 50%, 60%, 70%, 80% speed of design point is presented. The results of the performance test of compressor show a good agreement with the results of 3D CFD.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2015년도 제49회 하계 정기학술대회 초록집
• /
• pp.98.1-98.1
• /
• 2015

G-M극저온냉동기의 구동으로 인해 발생되는 크라이오 펌프의 진동 저감을 위해 각 요소에 해당하는 부품의 소재 및 모델 변경으로 설계에 반영하고자 한다. G-M극저온냉동기는 헬륨냉매를 사용하여 2개의 정압과정과 2개의 정적과정으로 구성되는 냉동사이클을 구성하는데, 구조적 특성상 내부 왕복기의 운동과 고저압변환에 따른 압력차이가 냉동기의 진동을 유발하므로 진공성능에 영향을 줄 수 있으므로, 이를 최소화하는 기술 개발이 필요하다. 헬륨냉매의 고압 유동에 따른 관로 압력증가로 인한 유동소음이 발생하는데, 이로 인한 소음을 줄이기 위해 관로의 최적화 설계/방진구조반영(DAMPER)으로 진동 안정화(Vibration Stabilization)설계를 수행 하고자 하며, 이에 따른 최적화 연구을 수행하고자 한다. 일차적으로, 기존 시스템의 진동측정을 통해 진동의 가진원을 밝히고 진동 전달경로를 파악하고자한다. 진동 가진원의 가진 최소화, 진동전달경로의 전달률 최소화, 고압유동에 따른 관로 설계 최적화를 진동해석, 탄성체 동역학해석, 그리고 유동해석을 통해 진동 및 소음의 최소화 방안을 도출하고자 한다. 해석결과를 토대로 진동가진원의 최소화를 위한 제품설계변경과 진동전달경로에 대한 방진을 위한 dmper 적용(전달률 최소화) 및 유동소음 최소화를 위한 damper나 관로 최적화 설계를 수행한다. 상기 기존시스템 측정/분석, CAE해석을 통한 진동/소음의 최적화방안도출 및 실제품 적용기술은 저진동 크라이오펌프 개발을 위한 기반 기술 확립에 크게 기여할것이며, 향후 크라이오펌프 고도화 및 최신 기술 제품 개발에 큰 기여가 기대된다.