• Journal of Korean Tunnelling and Underground Space Association
• /
• v.17 no.4
• /
• pp.473-485
• /
• 2015

The problems for non-rotating of a disc cutter proceed from the faults in inner parts of the disc cutter such as the leak of hydraulic fluid, the intrusion of tunnel mucks and water, overloading, overheating, poor assembly and substandard material. The rotating of a disc cutter is an indicator to show that the inner parts of disc cutter is operable, although the rotational torque depends on the extent of the damage. Therefore, the key in the problems for non-rotating of disc cutter is to maintain that the tapered roller bearings are working properly. This study aims to investigate the inner parts disassembled from disc cutters applied to the field tests in order to help decision for reuse of the disc cutters. As results, surface finishing to remove the scratch on the load zone of the hubs is needed, with the intent to reuse a hub. And the investigation of lapping surface by optical microscope of floating seals and the contamination test of oil need to be performed for reuse of a disc cutter. Especially, the analysis results show that the floating seals play a key role in the normal operation of bearings. There is nothing significant to report in the rest parts such as bearing, shaft, seal retainers.

• Fire Science and Engineering
• /
• v.30 no.4
• /
• pp.111-120
• /
• 2016

This is an experimental study to analyze the explosion and fire hazards of mobile phone batteries. Using the lithium-ion batteries currently used on smart phone as the experiment samples, the experiments were conducted by overcharging, internal and external short circuit, and thermal shock with the potential of explosion and fire caused by careless use or abnormal conditions. The experiment results showed that, in the case of overcharging and external short circuit, there was no explosion and fire hazard in the normal operation of the protection circuit module (PCM), but there were big risks when the PCM faulted conditions were assumed. In the case of the experiments by internal short circuit and thermal shock, such risks varied depending on a battery charge state. In other words, it could be verified that there were low risks of explosion and fire in a full discharge state, but there were high risks in a full charge state. These experiment results suggest that to minimize the explosion and fire hazards of mobile phone batteries, an alarm device is necessary when the PCM fault occurs. In addition, a solid battery case should be made and safety equipment, such as a cooling device to avoid high temperature, is needed.

• Journal of Life Science
• /
• v.28 no.9
• /
• pp.1100-1117
• /
• 2018

The Ras superfamily of small G-proteins acts as a molecular switch on the intracellular signaling pathway. Upon ligand stimulation, inactive GTPases (Ras-GDP) are activated (Ras-GTP) using guanine nucleotide exchange factor (GEF) and transmit signals to their downstream effectors. Following signal transmission, active Ras-GTP become inactive Ras-GDP and cease signaling. However, the intrinsic GTPase activity of Ras proteins is weak, requiring Ras GTPase-activating protein (RasGAP) to efficiently convert RAS-GTP to Ras-GDP. Since deregulation of the Ras pathway is found in nearly 30% of all human cancers, it might be useful to clarify the structural and physiological roles of Ras GTPases. Recently, RasGAP has emerged as a new class of tumor-suppressor protein and a potential therapeutic target for cancer. Therefore, it is important to clarify the physiological roles of the individual GAPs in human diseases. The first RasGAP discovered was RASA1, also known as p120 RasGAP. RASA1 is widely expressed, independent of cell type and tissue distribution. Subsequently, neurofibromatosis type 1 (NF1) was discovered. The remaining GAPs are affiliated with the GAP1 and synaptic GAP (SynGAP) families. There are more than 170 Ras GTPases and 14 Ras GAP members in the human genome. This review focused on the current understanding of Ras GTPase and RasGAP in human diseases, including cancers.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.40 no.1
• /
• pp.39-45
• /
• 2016

Thermal management of a fuel cell is important to satisfy the requirements of durability and efficiency under varying load conditions. In this study, a linear state feedback controller was designed to maintain the temperature within operating conditions. Due to the nonlinearity of automotive fuel cell system, the state feedback controller results in marginal stable under load condition from $0.5A/cm^2$ to $0.7A/cm^2$. A PWM (Pulse Width Modulation) and the modified state feedback controller are applied to control the temperature under the load condition from $0.5A/cm^2$ to $0.7A/cm^2$. The cooling system model is composed of a reservoir, radiator, bypass valve, fan, and a water pump. The performance of the control algorithm was evaluated in terms of the integral time weighted absolute error (ITAE). Additionally, MATLAB/SIMULINK$^{(R)}$ was used for the development of the system models and controllers. The modified state feedback controller was found to be more effective for controlling temperature than other algorithms when tested under low load conditions.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.165-165
• /
• 2017

모돈은 사육 특성상 제한된 파일롯 공간 안에 장시간 머물기 때문에 과중한 몸무게에 의한 지제 이상, 섭식 등의 불량, 수면상태의 불량 등을 지속적으로 관찰해야 하는 대상이다. 측면에 다수의 초음파 센서를 설치하여 기립의 상태 및 운동 시 몸체 궤적의 특성을 분석하여 종합적으로 모돈의 행동 특성을 정량화 하고자 하였다. 이 과정에서 계측 신호의 값을 대수적으로 비교하는 방식에 한계가 있음을 발견하였고, 이를 해결하고자 10 Hz/Ch 내외의 시계열 상대거리 궤적 신호를 주파수 도메인으로 변경하여 분석을 수행하였다. 일정 주파수에 집중되어 있는 주파수 값의 크기 변화(파워 스펙트럼 밀도)를 기준으로 모돈의 움직임의 정상 상태 유무 판별이 가능하였다. 단, 이러한 분석은 계측 데이터를 일괄 처리 방식으로 분석하는 방법으로 도출이 되었으므로, 계측과 정량 분석을 동시에 수행하기 위한 개선이 필요하였다. 계측 시스템에서 사용한 마이크로 프로세서는 Nucleo-446(STMelectronics, CA, USA)로 180 Mhz의 클럭 속도로 작동하나, 총 100 Hz 내외의 16비트 계측 신호에 대해 추가적으로 FFT 등의 주파수 변환 신호 처리를 수행하기에는 연산 능력이 부족하였다. 한편, 주파수 분석의 주기를 1분 단위로 할 경우 처리해야할 정보의 크기는 $100{\times}60{\times}5{\times}2Byte$ 이므로 1분 내에 해당 연산을 종료할 수 있는 추가의 연산 장치가 필요하였다. 계측과 주파수 도메인 변환 연산을 동시에 수행하기 위하여 1 Ghz의 연산능력을 가진 ARM A9 계열의 초소형 멀티코어 AP인 NanoPi Neo Air(Friendlyarm, Guangzhou, China)을 선정하였다. 4개의 코어를 각각 계측, Median 필터링, Smoothing 연산, FFT 분석에 사용하여 1분 단위, 2분 단위, 5분 단위의 주파수 분석을 동시에 수행하였다. 병렬 연산 라이브러리는 오픈 소스인 MPICH(www.mpich.org)를 이용하였다. 상대적으로 여유있는 자원을 보유하고 코어를 실시간으로 결정하여 다수의 모돈 개체 동시 모니터링을 위한 네트워크 연결 역할을 동시에 수행하도록 하였다. 1주일 내외의 요인 실험 수행 결과, 약 70 Mbyte의 데이터가 축적이 되었으며, 1분 단위, 2분 단위, 5분 단위의 주파수 도메인 변환 후 결과를 동시에 취득할 수 있었다. 일부 주파수 도메인 상의 파워 밀도 값이 모돈의 행동 특성에 분석에 유효한 정보를 제공함을 발견하였다. 모돈사 내 현장 보급이 가능한 초소형 AP와 멀티 코어 기반 병렬 처리 기법을 이용한 현장 진단 시스템 개발 연구를 지속적으로 수행할 것이다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.6
• /
• pp.650-655
• /
• 2016

In this study, a computational simulation of the internal flow characteristics was carried out for a Urea-SCR Injector. A single hole swirl injector with a swirl disk and slanted nozzle was used in this simulation. The maximum needle lift and opening velocity were selected as the design parameters. To analyze the unsteady internal flow characteristics of the Urea-SCR injector, the moving grid technique was applied to simulate the delicate needle movement. According to the simulation results, the injected mass flow rate from the Urea-SCR injector decreased with increasing needle opening velocity and maximum needle lift. This is because the Urea-solution tends to fill the empty space that the needle previously occupied. The swirl flow is decreased as the flow goes through the injector nozzle, because of the friction with the nozzle wall. Also, during the maximum needle lift period, the swirl coefficient and mean swirl coefficient increase with increasing needle lift. The results of this study may be used as the basic design data of related injectors.

• Journal of Energy Engineering
• /
• v.29 no.3
• /
• pp.97-102
• /
• 2020

In this study, one-way fluid structure interaction analysis was adapted to verify the durability of the outdoor evacuation stair structure operated in the event of a fire when wind pressure caused by a typhoon was applied. To this end, flow analysis was performed with the flow field around the structure of the evacuation stair in a steady state, and the durability was analyzed through structural analysis such as structural stress, deformation, and fatigue life using these analysis results by fluid data input data for structural analysis. As a result of flow numerical analysis, the air flow was different according to the shape of the evacuation stair structure, and this flow velocity distribution generated by the total pressure on the structure surface. Through the structural analysis results calculated by this total pressure, the safety factor calculated as the maximum stress value was found to be more than the safety factor, and durability was proven by fatigue life and deformation analysis.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.19 no.6
• /
• pp.643-648
• /
• 2013

In this paper, we developed a system which can detect and can alarm about the sailing provocative climate by using a photo. The research on domestic shipbuilding industry and in IT fusion technology is under construction, but a reliable safety device which can alarm a sailor about the circumstances of the fog and rain during ship operation as soon as possible due to the constant state in domestic. In this paper, a compact, for system low-power transceiver and data processing equipment for sensing were developed, also a performance evaluation got accomplished with simulation analysis. In results, it is operating normally at least 32.36[dB] and maximum values f 89.20[dB] in the domestic, and 32.55 to 60.66[dB] in the outdoors.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.3
• /
• pp.65-72
• /
• 2020

A refrigerator equipped with an ice dispenser has ice cubes in its ice bucket to discharge the required amount of ice. On the other hand, the ice cubes in the bucket may clump together if the refrigerator is filled with ice and is not used for a long time or during normal operation. Although a mechanism for separating the ice mass is provided, the ice mass cannot be removed completely if the ice blocking is severe. To solve this problem, after investigating the existing research on the process of ice entanglement and the separation force, this study tested ice extraction under a range of conditions of artificially entangled ices. In this process, new mechanisms are proposed to resolve the problem of existing ice storage features that prevent the extraction of ice and to expand the working radius of the icebreaking mechanism for full extraction. The prototype of the proposed mechanism was also fabricated in an actual refrigerator. As a result, the proposed shape and mechanism could extract the ice cubes in the bucket completely, while the existing ice dispenser could extract only 65%.

• Food Industry
• /
• s.218
• /
• pp.24-49
• /
• 2010

${\bigcirc}$ 본 업소는 어묵류(튀김어묵, 찐어묵, 구운어묵)을 생산하는 식품제조 가공업소로서 총 5명의 인원이 어묵류 15개 제품을 생산하여 매출액은(약 00원)이며 주도 대형 유통판매업소에 판매하고 있다. ${\bigcirc}$ 본 업소의 어묵은 연육, 농산물 등과 식품첨가물을 배합 성형 후 가열 등의 공정을 거쳐 생산된 제품으로, 원료 취급과정에서의 오염이나 불충분한 가열, 교차오염 등으로 식중독균(병원성대장균, 황색포도상구균 등)과 원료 및 제조과정에서 이물(금속 등)이 혼입될 수 있으며, ${\bigcirc}$ 이로 인한 주요클레임 발생사례는 최근 3년간 관계당국으로부터 대장균군 검출 3건, 소비자클레임 2건이 있었다. - 연도별 주요 클레임내용은 '08년도에는 대장균군 검출 3건, '09년도 튀김어묵에서 날벌레 이물 검출 1건, '10년도에는 찐어묵에서 철수세미 1건 이었다. ${\bigcirc}$이러한 위해발생을 사전에 예방하기 위해 중점관리해야 하는 공정은 가열공정으로 판단되며, 금속등의 이물혼입 또한 중점적으로 관리할 필요성이 있다. ${\bigcirc}$ 본 업소에서 생산하는 어묵류(튀김어묵, 찐어묵, 구운어묵)는 가열공정에서의 가열온도와 시간을 각각 설정하여 CCP 1로 관리하고 있으며, 품온이 $85^{\circ}C$이상으로 유지될 수 있도록 2시간마다 모니터링하고 한계기준 이탈여부를 기록하도록 하고 있다. ${\bigcirc}$또한 금속검출공정을 CCP 2로 관리하여 2mm${\varphi}$ 이상의 금속이물 혼입여부를 상시 확인하고 있으며, 금속검출기의 정상 작동여부를 4시간마다 모니터링하고 기록하도록 하고 있다. ${\bigcirc}$종합적인 공정 및 일반위생관리를 위해 개인위생 상태 냉동, 냉장고 온도 확인 등 총 29개 항목에 대하여 정기적 점검(매일 17, 주간 4, 월간 4, 분기 1, 연간 3)을 실시하고 있으며, ${\bigcirc}$따라서 지속적인 모니터링을 통해 미흡사항의 원인으로 파악하고 문제점 제거를 위해 체계적이고 지속적인 관리가 필요하다.