• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.20 no.3
• /
• pp.243-253
• /
• 2002

These days, the application range of digital photogrammetry is being extended actively, so the great variety of research is being progressed about improvement of measurement accuracy. This method can acquisite a high analysis accuracy and can acquisite easily image. But, So this method require a much processing time and effort by increasing a data amount, as the automation of processing must be completed for efficiency improvement of processing. In this study, the automation of image processing stage is established for multi-image aquisition and analysis about a radio telescope. Also, the precise measurement and the accuracy on object were intended to be improved. As a result of this study, the accuracy on the object which demands precise measurement was enhanced from multi image analysis, and also the assembly accuracy of the object could be checked by precise measurement and curve fitting.

• Spatial Information Research
• /
• v.12 no.2
• /
• pp.181-191
• /
• 2004

Nowadays, GPS-photogrammetry can be applied to the basemap production, a land register and NGIS. And from now on, as the increase of GPS receiver rate, the study on the interpolation methods considering the exact movement of an aircraft at photoflight and the study on the supplement of GPS defect by INS are required continuously. GPS-Photogrammetry, which are based on the direct measurement of the projection centers and attitude at the moment of camera exposure time through loading the GPS receiver in aircraft. This photogrammetric methods can of for us to acquire the exterior orientation parameters with only minimum ground control points, even the ground control process could be completely skipped. Consequently, we can drastically reduce the time and cost far the mapping process. In this thesis, two test flights were conducted in area to evaluate the performance of accuracy and efficiency through the analysis of results between the two photogrammetric methods, that is, traditional photograrammetry, GPS-Photogrammetry. Test results shows that a large variety of advantages of GPS-Photogrammetry against traditional photogrammetry is to be verified. Especially, the number of ground control points for the exterior orientation could be saved more than 70～80%, and the cost far map production 30～50%, respectively. In addition, it was convinced that the large reduction of control points has not any effect on the block accuracy.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.16 no.4
• /
• pp.54-63
• /
• 2013

In this paper, we evaluate the accuracy of the vertical positioning by distance using Network RTK-GPS. The experimental results confirm that Network RTK-GPS method can acquire data quickly and accurately than conventional leveling methods so that the Network RTK-GPS method is a relatively efficient and economical way for the vertical positioning. Results of validation using permanent GPS stations indicate that visible satellites, PDOP, and VDOP are very good for the vertical positioning. Integrated reference points such as U0997 and U0921 are satisfied with 3 ratings in the rules of public leveling and all the rest are proved improper. When the vertical positioning using Network RTK-GPS is implemented, the geoid height of EGM2008 should be applied for leveling. If the number of geodetic satellite are increasing in the near future, the vertical positioning using Network RTK-GPS can be possible in all the range.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.28 no.1
• /
• pp.153-160
• /
• 2010

It is necessary to determine accurate 3-dimensional coordinates of the building corner points that could be control or check points in order to verify the accuracy of 3D digital maps in the near future. The usual process of obtaining the coordinates of the building corner points is to set up the ground control points with a GPS and then to practice terrestrial survey such as distance or angle measurements. However, since an error in the ground control points can be propagated through the terrestrial survey into the final coordinates of the buildings, accurately should be considered as much as possible. The actual effect of the GPS-derived ground control point error on the estimates of the unknowns through the terrestrial survey is mathematically analyzed, and the simulation data is tested numerically. The error of the ground control points is tested in the cases of 1-4 cm for the horizontal components and 2-8 cm for the vertical component. The vertical component error is assigned twice the horizontal ones because of the characteristics of the GPS survey. The distance measurement is assumed for convenience and the precision of the estimated coordinates of the building corner points is almost linearly increased according to the errors of the ground control points. In addition, the final estimates themselves can vary by the simulated random errors depending on the precision of the survey instrument, but the precision of the estimates is almost independent of survey accuracy.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.40 no.4
• /
• pp.325-332
• /
• 2022

Determination of VLBI IVP (Very Long Baseline Interferometry Invariant Point) position with high accuracy is required to compute local tie vectors between the space geodetic techniques. In general, reflective targets are attached on VLBI antenna and slant distances, horizontal and vertical angles are measured from the pillars. Then, adjustment computation is performed by using the mathematical model which connects measurements and unknown parameters. This indicates that the accuracy of the estimated solutions is affected by the accuracy of the measurements. One of issues in local tie surveying, however, is that the reflective targets are not in favorable condition, that is, the reflective sheet target cannot be perfectly aligned to the instrument perpendicularly. Deviation from the line of sight of an instrument may cause different type of measurement errors. This inherent limitation may lead to incorrect stochastic modeling for the measurements in adjustment computation procedures. In this study, error characteristics by measurement types and pillars are analyzed, respectively. The analysis on the studentized residuals is performed after adjustment computation. The normality of the residuals is tested and then equal variance test between the measurement types are performed. The results show that there are differences in variance according to the measurement types. Differences in variance between distances and angle measurements are observed when F-test is performed for the measurements from each pillar. Therefore, more detailed stochastic modeling is required for optimal solutions, especially in local tie survey.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.19 no.3
• /
• pp.283-290
• /
• 2001

This paper demonstrates the performance of industrial precise measurement using the digital close-range photograrmmetric system based on a off-the-shelf CCTV-type CCD camera. The system was constructed with a CCD camera and a PC with a frame grabber, coupled with digital image mensuration and self-calibrating bundle adjustment techniques. An artificial fish reef with cubic shape was taken as an object for the application test of the system and the digital images were acquired on multi-station convergent network around the object. The geometric calibration of the CCD camera and the phototriangulation of the entire surface of the object was carried out simultaneously by means of self-calibrating bundle adjustment technique. Also the system comprising a high resolution still-video camera Kodak DCS, which high accuracy potential has been already established, were employed in similar network condition. Then the results from two different camera systems were compared in the accuracies of phototriangulation.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.23 no.4
• /
• pp.359-366
• /
• 2005

Airborne LiDAR integrated with on-board GPS/INS and scanning technology is a state-of the-art system for direct 3D geo-spatial data acquisition. In this study, LiDAR data were calibrated using ground points in calibration site for the higher system accuracy. The accuracy results are ${\pm}15{\sim}30\;cm$ in horizontal and ${\pm}15\;cm$ in vertical. The results show that LiDAR system has capability for precise DEM and contour generation, 3D urban modeling and engineering design.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2008.05a
• /
• pp.1799-1803
• /
• 2008

표면영상유속계는 하천 표면의 영상을 분석하여 유속을 산정하는 매우 실용적이며 간편한 장비이다. 그러나, 표면영상유속계를 이용하여 유량을 산정하고자 할 경우, 하천 표면의 평면 측량 자료와 하천의 단면 측량 자료가 반드시 필요하다. 이 때문에 표면영상유속계의 간편성과 유용성에도 불구하고, 이용자들이 쉽게 이용하기 어렵다는 그릇된 인식을 줄 수 있다. 만일 효율적이고 간편하게 하천의 단면을 추정할 수 있다면, 표면영상유속계를 마치 일반적인 프로펠러 유속계처럼 쉽게 이용할 수 있을 것이다. 이 연구는 일반적인 평면 측량없이, 두 대의 비디오 카메라로 이루어진 표면 영상 유속계를 이용하여 하천 평면을 계측하는 방법을 개발하는 것이다. 이를 통하여 표면 영상 분석 과정을 반자동화할 수 있게 된다. 두 대의 카메라를 이용한 평면 측량은 사진 측량 분야이나 컴퓨터 비전 분야에서 오랫 동안 연구되어 왔다. 이 기법을 표면영상유속계에 적용함으로써 간단하게 하천의 평면 좌표를 구할 수 있도록 하였다. 두 대의 카메라에 대해서는 직접 선형 변환법을 이용하여 내부 표정과 외부 표정을 수행하여 변환의 매개 변수들을 추정하였다. 추정된 변수들과 공간 전방 교회법을 이용하여 하천의 고정된 기준점들의 좌표를 측정한다. 측정된 좌표점들은 기울어진 영상을 연직으로 사영된 평면으로 변환하는 데 이용되며, 이 과정을 통하여 번거로운 하천의 평면 측량 과정을 생략할 수 있게 되었다. 온천천에 실제 적용하여 본 결과, 결과는 아직은 만족할 만한 정도는 아니나, 보다 정밀한 카메라의 보정 등을 통하여 보다 나은 결과를 도출할 수 있을 것으로 기대된다.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.26 no.4
• /
• pp.323-331
• /
• 2008

Digital close-range photogrammetric technique can measure and describe 3D geometric form from 2D image. This technique is a growing applicability in the field of sciences. Nevertheless, civil and mechanical field, which need measurements as precise as possible, use expensive measuring instruments in general. In addition there are occasions for analysis by means of visual method, since appropriate measuring instruments have been not yet available. This study therefore developed digital close-range photogrammetric technique with a movable orientation board to quickly measure deformation before and after destruction from simulated ground model of reinforced-soil wall. Then the results are compared with the measurements obtained using digital theodolite.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.29 no.3
• /
• pp.283-291
• /
• 2011

In case of metric cameras, not only fiducial marks but also various parameters related to camera lens are provided to users for the interior orientation process. The parameters have been acquired through precise camera calibration in laboratory by camera maker. But, in case of non-metric cameras, the interior orientation parameters should be determined in person by users through camera calibration with great number of control points. The interior orientation parameters of metric cameras are practically used for long time. But in case of non-metric cameras, the long-term stability of the interior orientation parameters have not been established. Generally, the interior orientation parameters of non-metric cameras are determined in every photogrammetric work. It's been an obstacle to use the non-metric camera in photogrammetric project because so many control points are required to get the interior orientation parameters. In this study, camera calibrations and photogrammetric observations using a non-metric camera have been implemented 25 times periodically for 6 months and the results have been analyzed. As a result, long-them stability of the interior orientation parameters of a non-metric camera is analyzed.