• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.41 no.7
• /
• pp.585-590
• /
• 2017

Vehicle behavior is determined by forces and a torques generated at the ground contact surface of the tire. Various tire models are used to calculate the forces and torques acting on the tire. The brush model calculates the forces and torques with fewer coefficients than other tire models. However, owing to fewer degrees of freedom in calculating the forces, this model has limitations in precisely expressing measured data. In this study, this problem was addressed by adding the least parameters to the friction coefficient and tire properties of the brush model, and the proposed model was validated.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.11
• /
• pp.2049-2058
• /
• 1992

In this work, a 6 degree of freedom lumped mass model is constructed for an OHC-type cam valve train analysis, and the model is verified experimentally. Using the verified model, an optimum cam profile is designed to minimize the maximum contact force between cam and follower under the constraints such as cam lift and cam event angle. The designed cam was carefully machined and tested experimentally. As operating the designed cam shaft on the test rig, the valve motion was precisely measured with laser displacement meter and the contact force was indirectly monitored by measuring strain at a certain point of the finger follower. Judging from the model simulation and experiment results, the maximum contact force can be reduced as much as more than 16.7 percent under maintaining the original valve flow area by adopting the optimum cam profile.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.8
• /
• pp.913-920
• /
• 2012

An efficient 3D finite element walking model that considers the detailed shapes of muscles, ligaments, bones, skin, and soles was developed based on a real computed tomography (CT) scan image of a foot, and nonlinear contact analyses were performed to investigate pressure changes. The highest pressure occurs at the rear bottom of the foot when standing and walking. The pressure on the outsole with a curved foot bottom surface is lessened and distributed over a wider area than in the case of a flat outsole. The result shows that a shoe sole shape optimized for diabetes patients can relieve the foot pressure concentration and prevent further worsening of symptoms.

• Bulletin of the Korean Space Science Society
• /
• 2003.10a
• /
• pp.22-22
• /
• 2003

1998년 12월부터 1999년 5월까지 총 10일간 소백산천문대의 61cm 망원경과 PM512 CCD 카메라를 이용하여 W UMa형 접촉 식쌍성 AM Cnc의 CCD 측광관측을 수행하여 BVI 광도곡선을 완성하였다. 새로운 광도곡선으로부터 주극심시각 2점, 부극심시각 3점을 얻었다. 이 관측치를 포함하여 AH Cnc의 관측된 모든 극심시각을 수집하여 분석한 결과, 영년 주기 증가를 보이고, 변화 원인을 질량이 큰 별에서 질량이 작은 별로의 보존적 질량이동에 의한 것으로 해석하였다. 영년주기 증가율은 3.18$\times$$10^{-7}$ day/year이다. 새로운 BVI 광도곡선을 WD 쌍성 모델의 접촉모드(Mode 3)로 분석하여 측광해를 산출하였고, 측광해의 결과는 질량비 0.159, 궤도경사각 86$^{\circ}$, 접촉도(fill-out factor) 49%등으로 계산되었다. 측광해를 Sandquist & Shetrone(2003)의 연구결과와 비교하면 질량비와 궤도경사각은 거의 같고, 접촉도는 약간 작은 값이다. 작은 값이다.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1992.10a
• /
• pp.90-96
• /
• 1992

경계면 요소를 이용하여 철근콘크리트 구조물의 접촉면 문제를 유한 요소법으로 해석하는 기법에 대하여 연구한다. 본 연구에서는 경계면 요소의 수치해석의 이론과정을 전개하고, 실험 관찰된 부착 시험체에 적용하여 이형철근과 콘크리트 부착기구의 접촉면을 해석한다. 경계면은 특별한 연결요소를 이용하여 재현하며 Mohr-Coulomb의 마찰 이론을 응응한다. 해석의 주요점으로 하중상태에 따라 변화되는 경계면의 접촉상태, 즉 고정(stick), 미끄러짐(slide), 분리(separation)를 묘사하여 경계면 재료의 비선형 거동을 관찰한다. 부착모델의 해석결과는 실험실의 결과와 대체로 일치되며 따라서 철근콘크리트 접촉면의 응력해석을 위해 경계면 요소가 활용될 수 있음을 보여준다.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.1
• /
• pp.125-132
• /
• 2011

The dynamic characteristics of valve train are responsible for the dynamic performances of engine. We derived the equation of motion for 6 degrees of freedom model of the valve train. Computer model is also developed with flexible multibody model considering contact between components. The simulation results with these two models are compared with experimental results. We investigated the effect of the two spring models, TSDA (Translational Spring Damper Actuator) element and flexible body model, on the valve behavior and spring force. It is found that the dynamic behavior of the two models are not very different at normal operational velocity of the engine. By modeling contact between cam and tappet, the stress distributions of the cam were found. Using stress distribution obtained, contact width and contact stresses of the cam surface were calculated with Hertz contact theory.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.22 no.4
• /
• pp.68-77
• /
• 2008

When we design the grounding grid, dangerous voltage IEEE Std. 80 method has been commonly used in the domestic area. However there is not appropriative examination of ground design environment. So in this paper, we examined of IEEE Std. 80 touch voltage method's marginal utility and we induced corrective factor for those problems by comparison between IEEE Std. 80 touch voltage value and simulation experimentation value. Moreover, Logistic model's corrective factor we proved the maximum accidental error has reduced less than 10[%].

• Proceedings of the Membrane Society of Korea Conference
• /
• 1997.10a
• /
• pp.61-64
• /
• 1997

1. 서론 : 적절한 이산화탄소의 분리는 지구온난화의 가속현상을 늦출 수 있을 뿐만 아니라 각종 탄화수소가스의 원료로 분리 정제된 이산화탄소를 재이용할 수 있으므로 경제적으로 매우 중요하다. 이산화탄소 분리에 사용되던 기존 공정들의 단점을 보완할 수 있는 대체방안으로 최근에 개발되기 시작한 것이 소수성의 다공성 고분자 분리막(hydrophobic porous ploymeric membrane) 방법인데, 이는 모듈의 유효 막 표면적이 상대적으로 크고 기체와 액체의 흐름을 독립적으로 제어할 수 있으므로 범람 등의 현상이 없으나 막 자체의 저항이 비교적 큰 단점을 가지고 있다. Qi와 Cussler는 이러한 특성을 가지는 중공사막 모듈에서의 기-액 흐름에 대한 물질전달 상관관계식을 얻었으며[1], Karoor 등은 여러 가지 중공사막 모듈을 사용하여 순수물과 diethanolamine(DEA) 등의 흡수제에 대한 이산화탄소의 물질전달 거동을 수치모델과 실험을 통하여 고찰하였다[3]. 또한 중공사막 접촉기의 실제적 응용에 대하여 Matsumoto 등은 화력발전소에서 발생하는 연소가스 내의 이산화탄소 흠수에 대한 연구를 수행하였다[4]. 본 연구에서는 중공사막 접촉장치를 사용하여 흡수제를 순수물과 탄산칼륨($K_2CO_3$)을 사용했을 경우의 이산화탄소의 분리 거동을 수치모델과 실험을 통하여 고찰하였다. 수치모델의 경우 이전까지의 연구가 반응이 없는 경우나 반응식을 간략화시킨 경우에 한정되었는데 비하여, 반으이 있는 경우 각각의 반응물질들의 거동을 고려한 반응식을 유도하여 해를 구하고자 하녔다.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.15 no.6
• /
• pp.41-49
• /
• 2016

To evaluate lubrication properties by surface roughness under boundary and mixed lubrication, a new approach is suggested by both asperity flow and contact with stochastic characteristics. Many researchers already have studied the effect of surface roughness on flow. But, it has become important to research of the phenomenon of asperities contact in surfaces because the growth of asperities contact area under heavy load conditions. In this paper, flow factors in the average flow model derived by Patir and Cheng were used, and a multi-asperity contact model was included to calculate lubrication properties of a surface with a randomly generated rough surface. A numerical analysis using the average Reynolds equation with both the average flow model and the asperity contact model was conducted, and the results were compared with those from previous research. The results showed that the influence of asperities on lubrication and the friction coefficient changed rapidly on application of contact model.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.10
• /
• pp.1237-1242
• /
• 2011

The A detailed 3D finite-element analysis model of a human foot has been developed by converting CT scan images to 3D CAD models in order to analyze the distribution of plantar pressure. The 3D foot model includes all muscles, bones, and skin. On the basis of this model and the pressure distribution results, shoes for diabetes patients, which can make the plantar pressure distribution uniform, may be designed through finite-element contact analysis.