• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.05a
• /
• pp.82-85
• /
• 2008

When a projectile travels at high speed underwater, supercavitating flowarises, in which a huge cavity is generated behind the projectile so that only the nose, i.e., the cavitator, of the projectile is wetted, while the rest of it should be surrounded by the cavity. In that case, the projectile can achieve very high speed due to the reduced drag. Furthermore if the nose of the body is shaped properly, the attendant pressure drag can be maintained at a very low value, so that the overall drag is also reduced dramatically. In this study, shape optimization technique is employed to determine the optimum cavitator shape for minimum drag, given certain operating conditions. Simultaneous optimization technique is proposed for efficient cavitator shape optimization, in which the cavity and cavitator shape are determined in a single optimization routine.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.54 no.1
• /
• pp.33-39
• /
• 2005

Comparing with the conventional transformer without the air gap, a contactless transformer with the large air gap between the long primary winding and the secondary winding has increased leakage inductance and reduced magnetizing inductance. For transferring the primary power to the secondary one, the high frequency series resonant converter has been widely used for the contactless power supply system with the large air gap and the increased leakage inductance of the contactless transformer However, the high frequency series resonant converter has the disadvantages of the low efficiency and high voltage gain characteristics in the overall load range due to the large air gap and the circulating magnetizing current. In this paper, the characteristics of the high efficiency and unit voltage gain are revealed in the proposed three-level series-parallel resonant converter. The results are verified on the simulation based on the theoretical analysis and the 5kW experimental prototype.

• Transactions of the Korean hydrogen and new energy society
• /
• v.7 no.2
• /
• pp.129-135
• /
• 1996

Voltage-current profiles are measured when hydrogen-oxygen gas is in contact with solid polymer membrane ($Nafion^{(R)}$) as the electrolyte. The feed gas is prepared by mixing hydrogen and oxygen gas in various ratios. The carbon gas diffusion electrodes contacting the electrolyte are treated by platinum catalyst. The platinum surface is impregnated with a 5% $Nafion^{(R)}$ solution to ensure its good surface contact with the electrolyte. The constant voltage between anode and cathode was applied by a DC power supply. The results on the profiles show that the energy efficiency critically depends on the hydrogen concentration in $H_2/O_2$ mixture gas.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.176-176
• /
• 2010

OLED(Organic Light Emitting Device)는 LCD(Liquid Crystal Display)의 뒤를 잇는 차세대 디스플레이의 선두주자로서 자체발광형이기 때문에 백라이트 등의 보조광원이 불필요하며, 구동전압이 낮고 넓은 시야각과 빠른 응답속도 등의 특징을 가지고 있다. 또한 플렉서블 기판을 사용할 수 있어 차세대 디스플레이인 플렉서블 디스플레이에 적합하다. 플렉서블한 디스플레이를 만들기 위해서 플라스틱 기판에 OLED 물질을 사용하여 기존에 무겁고, 깨지기 쉬우며, 변형이 불가능한 유리로 만든 소자 보다 더 가볍고 깨지지 않고 변형이 가능한 플렉서블 디스플레이를 제작 할 수 있다. 그러나 플라스틱 기판은 매우 큰 투습율을 가지고 있어 OLED소자에 적용시키면 공기 중의 수분이나 산소와 접촉이 많아져 쉽게 산화되어 소자의 효율 및 수명이 짧아진다. 또한 OLED에 사용되는 유기물도 산소나 수분에 의해 특성이 급격히 저하되기 때문에 산소 및 수분의 차단은 필수적이다. 이러한 단점을 최소화하기 위해서 PECVD(Plasma Enhanced Chemical Vapor Deposition)로 만든 SiON(Silicon Oxynitride), $SiO_2$(Sillicon dioxide), $Si_3N_4$(Sillicon nitride) 박막을 차단막(Passivation layer)으로 사용하였다. PECVD(Plasma Enhanced Chemical Vapor Deposition)로 만든 SiON(Silicon Oxynitride), $SiO_2$(Sillicon dioxide), $Si_3N_4$(Sillicon nitride) 각각의 박막의 Crack의 특성을 85%-$85^{\circ}C$조건에서 24hr 측정하였다.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.6
• /
• pp.1669-1678
• /
• 1990

The annular and coaxial swirl flows between which LPG is supplied was selected to study the swirling flames in double co-swirl flows. The objective of this study is to research into the effects of double co-swirl flow conditions on the stability limit, the reverse flow boundary, and the time mean temperature distributions of the swirling flames. The increase of swirl intensity of axial flow makes the stability limit decrease, but the annular swirl flow (SM>0.5) makes stability and swirl intensity of axial flow increase, And the existence of axial swirl flow makes flame intensive and small in size, and this may be applicable to the design of high power compact combustor.

• Journal of Korean Society on Water Environment
• /
• v.21 no.1
• /
• pp.92-98
• /
• 2005

Nutrients removal performance of a contact oxidation reactor covered with soil was investigated when basalt rubble was used as a contact medium under various operating conditions. The objective of the experiment was to determine the effectiveness of the system by measuring the removal efficiencies of nutrients from a technical and economical viewpoint. Under the ranges of HRT(20 and 40 hrs) in the experiment, the removal rates of organic matter were as high as 97.5% by showing an effluent $BOD_5$ of less than 10 mg/L. The test of nitrogen removal when the turf was planted on the top soil showed that the average removal rate increased as much as 25% as compared to that without planting. It was suggested that the construction and maintenance cost could be reduced over 20% when the HRT of the system was decreased from 72 to 40 hrs.

• Journal of Advanced Navigation Technology
• /
• v.18 no.6
• /
• pp.633-639
• /
• 2014

Recently the study about a smart health care which is combined IT with BT to provide a variety of health care services are being actively investigated. In order to provide the best possible emergency medical services in a short period of time, it is necessary that the rapid emergency measures in the event of an emergency essential. In this paper, we propose an emergency medical service platform to take effective first aid to person who has a NFC tag or NFC-enabled mobile smart phones in an accident. Using NFC, it is possible to help without physical contact to the patient unconscious to emergency incidents such as falling down in everyday life. In this paper, we design and implement an mobile emergency medical system that can deliver first aid information ask for help in case of emergency.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.6 no.3
• /
• pp.270-272
• /
• 2005

The behavior of surface oxidation on cobalt silicide layer was investigated under rapid thermal oxidation (RTO) conditions. The cobalt silicide layer was prepared on p-type silicon substrates. We used Ti thin film as a capping layer in order to measure the degree of oxidation of the layer. Oxide grew faster on the cobalt silicide prepared with the Ti capping layer to reach ca $500{\AA}$ at $700^{\circ}C$ in thickness. The oxide film kept growing under $550^{\circ}C\~700^{\circ}C$ of the RTO condition, resulting in a saturated state above $500{\AA}$.

• Resources Recycling
• /
• v.12 no.4
• /
• pp.44-50
• /
• 2003

Separation of mixed plastics is not a simple task due to similarities of specific gravity and limitations of sizes, etc. In this study, a new technique was developed to separate plastics selectively by a thermal adhesion method using the different softening or melting temperatures of various types of plastics. Tests were conducted to investigate softening or melting temperatures and adhesion probabilities of plastics with change in temperature. Tests also were conducted to analyze the operating variables, including contact times, size and color pigment. It was founded that LDPE, HDPE and PVC, PET, etc among mixed plastics could be separated selectively according to the change of temperature.

• Resources Recycling
• /
• v.7 no.2
• /
• pp.9-15
• /
• 1998

Recovery af molybdenum in spent desulfuriring catalyst of petrochemical industries was studied from MfGnatc solulion which is a resultant of firstly remvercd vanadium by wet processes. In order to separate and recover molybdenum from upper mentioned rafinatz solution containing several mctal ions, such as molybdenum (1,100 ppm), vanadium (150 ppm), aluminium (19 ppm), and nickel (33 ppm), either adsorption technique by chelate resin or solvent extr~ction by tertiary amine as extractant was applied. In case of adsorption method, palyamine type chelate resin showed the highest selectivily far molybdenum ion up lo 60 ddm' of ancentration aftcr eluting with 3.0 rnolld~n' of NH,OH. On the othcr hand. molybdenum ion wa cffectlvely cxtractcd in Ule whole ranges of equilibrilrm pR by solvent extraction method with 10 ~01%-alamine 336 which was pretreated with 2N-HCI