• Journal of Korean Society of Steel Construction
• /
• v.12 no.2 s.45
• /
• pp.143-150
• /
• 2000

Depending upon the combination of tolerances specified in the standards on bolt, nut and washer for high tension bolt sets, there arises center-to-center deviation between bolt and washer. This deviation nay cause loss of effective contact area between nut- and washer-faces, which leads to some dispersion of the torque coefficient K. By adapting circular arc surface instead of flat surface for the nut, it is shown through numerical analyses that the dispersion of the torque coefficient can be minimized. In this way, optimum radius of curvature of the nut bearing surface is proposed.

• Korean Journal of Optics and Photonics
• /
• v.16 no.3
• /
• pp.177-181
• /
• 2005

Although there are many ways to measure the diameter of a cylindrical object, in this study, the diameter of a cylindrical objects were measured by the geometric optical method and interference-diffraction method which are two kinds of tipical non-contact methods. In geometric optical method, the curved laser beam is formed on the cylindrical surface by spreading the inclined laser beam using the cylindrical lens. The curve is captured by CCD camera and the diameter is calculated by geometry. And the interference and diffraction patterns of investigated cylindrical objects are analyzed in interference-diffraction method. In this study, the cylindrical objects, whose diameters are $0.05\;mm\;\~\;100.50\;mm$ were measured by the geometric optical method and interference-diffraction method. The results show that in each method, the relative errors of the measurement are within $2\%$ and $1\%$, respectively and these non-contact methods can be applied in the quick measurement of many objects.

• Resources Recycling
• /
• v.7 no.5
• /
• pp.41-45
• /
• 1998

A Hew way of contact angle measurement is derived based on simple geometrical calculation. Without using complicated contact angle measurement instrument. Just measuring the diameter and height of liquid lens made it possible to calculate the contact angle value with a reasonable reliability. To validate the contact angle value obtained by this method, contact angle of the same liquid lens is measured using conventional goniometer and it is verified that two values are nearly same within the limit of observational error.

• Proceedings of the KAIS Fall Conference
• /
• 2001.11a
• /
• pp.111-116
• /
• 2001

본 논문에서는 유체기계에서 사용되고 있는 홀로제트밸브의 감속기에 대하여 APM S/W로 시뮬레이션(simulation) 하였다. 수압과 외부의 힘에 의해서 전달되는 베벨기어의 설계검증 및 재설계 관하여 시뮬레이션을 하였다. 도면의 재원을 변경시키지 않고 기어의 수명을 시뮬레이션한 결과 SM45C를 Martempering하여 사용할 시 기어의 수명이 짧아 적절치 못하였고 고주파열처리강, 질화열처리강을 사용할 경우 기어의 수명시간이 12,957-20,983시간 이였고 침탄강을 사용할 시 기어의 수명은 영구적이었고 소재의 경도가 우수할수록 더 많은 허용굽힘응력과 허용접촉응력을 받을 수 있다는 것을 시뮬레이션을 통하여 입증된다. 그리고 기어의 검증결과로 기어를 다시 설계할 경우 고주파나 질화강으로 하여 기어의 잇수가 1-3개만 늘어나고, 피치원의 지름이 4-12mm늘어나면 영구적으로 사용할 수 있고 침탄강을 사용할 시 치폭이 3mm줄어들고, 기어 잇수가 1-3개 줄어들고 피치원의 지름이 4-13mm 줄어들어 감속기를 경량화 시킬 수 있다는 것을 시뮬레이션을 통하여 입증되었다.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.2138-2139
• /
• 2011

본 논문에서는 44V AC 및 DC전원에서 직렬아크에 의한 전선 접속부에서의 산화물 성장 특성에 대하여 실험, 분석하였다. 실험에 사용된 전선은 동전선과 황동선으로 각각 지름 1.0mm을 사용하였으며, 교류의 경우 3가지 접속조건, 직류의 경우 4가지의 접속 조건으로 하여 전선 접촉면에서 직렬아크가 발생하였을 때 2A, 3A, 4A의 전류에서 산화물의 성장 특성과 접촉면 양단의 전압강하 변화, 산화물의 성장 길이 및 방향, 온도 분포 등에 대하여 분석하였다. 실험, 분석결과, 동전선과 동전선의 접속에서 가장 산화물의 성장이 잘 이루어짐을 볼 수 있었으며, 교류에서는 접촉면을 중심으로 좌우로, 직류에서는 접촉면을 중심으로 +극(양극) 방향으로만 산화물이 성장함을 볼 수 있었다. 본 연구 결과는 AC 및 DC 전원에서의 전기안전을 위한 기술 자료로 활용할 수 있을 것으로 기대된다.

• Journal of Energy Engineering
• /
• v.8 no.2
• /
• pp.272-278
• /
• 1999

In the present study, measurements of thermal contact resistance (TCR) were conducted for joints of brass and aluminium cylinders of 30 mm in diameter, 45 mm in length, when their interfaces were; ⅰ) under vacuum, ⅱ) charged with a pure silicone grease and ⅲ) charged with a mixture of silicone grease and powder of aluminium (#325). Also the data were compared with analytical calculations using Fouche's model. The data of TCR for joints under vacuum state varied in the range of (2∼100)${\times}$10$\^$-5/(㎡$^{\circ}C$/W) depending on their surface roughness. When the contact surfaces were carefully ground, a reduction of 30∼50% in TCR was obtained. But the surface treatment with silicone grease gave rise to a reduction of about 5∼10 times more than that of vacuum state. The analytical prediction by Fouche's model showed a good agreement within 10~30%, for the case of contact surface charged with silicone grease.

• Journal of Energy Engineering
• /
• v.9 no.1
• /
• pp.41-46
• /
• 2000

인류가 발생시키는 이산화탄소를 액화시켜 해양에 저장 또는 용해시키는 방법이 지구온나화 현상을 완화시키는 기술로 알려져있으며, 이 방법을 발전시키기위해서는 심해에 분사된 이산화탄소 액적의 용해거동을 정확히 예측하여야한다. 본 연구에서 중층심해 1000m와 1500m 깊이에 분사된 액체 이산화탄소 액적의 용해거동을 계산한 결과, 해저 약 4500m 깊이에서 이산화탄소의 밀도와 용해도가 가장 크게 변하였고, 분사된 이산화탄소는 초기 액적 지름이 각각 0.010m 그리고 0.015m 이하일 때 500m 이하의 깊이에서 완전히 용해되었다. 그리고 해수와 액체 이산화탄소의 접촉면에 생성되는 하이드레이트막이 이산환탄소 용해에 장애물로 작용한다는 것을 확인하였다.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.1010-1015
• /
• 2003

Bubble growth on microheater has been experimentally investigated in this study. The experiment was performed using platinum microheaters having dimensions of 300 ${\mu}m$ or 50 ${\mu}m$ in length, 20 ${\mu}m$ or 5 ${\mu}m$ in width, and $0.2{\pm}0.01$ ${\mu}m$ in thickness. A high speed video camera was used to observe bubble growth at 2,000 frames per second. Microheater temperature was measured at the rate of 300 Hz. with a data acquisition system. Bubble nucleation frequency increased with working fluid temperature. Although the slope of temperature drop was similar in all cases, the magnitude of temperature drop was different. The temperature profiles and the high speed camera images were combined to explain temperature drop.

• Journal of the Korean Vacuum Society
• /
• v.18 no.5
• /
• pp.337-345
• /
• 2009

When the drill hole diameter for the package substrate is under $100{\mu}m$, the smear in the drill hole cannot be eliminated by wet desmear process only. We intended to change the substrate's hydrophobic characteristics to hydrophilic characteristics by adapting the atmospheric pressure plasma prior to the wet desmear process. Atmospheric pressure plasma process was made as the inline type equipment which is adequate for the package substrate's manufacturing process and remote DBD type electrodes were used for the equipment. As the result of atmospheric pressure plasma processing, the contact angle of the substrate was enhanced from 71 degree to 30 degree. Dielectric film thickness, drill hole diameter and surface roughness were measured to evaluated the characteristics of the wet desmear process in case of plasma processing and in case of none. By the measurement, it was analyzed that the process uniformity within the whole panel was largely enhanced. Also, it was verified that the smear in the drill hole was eliminated efficiently which was analyzed by the SEM image of the drill hole.

• Composites Research
• /
• v.18 no.6
• /
• pp.9-18
• /
• 2005

With the wide applications of fiber-reinforced composite material in aero-structures and mechanical parts, the design of composite joints have become a very important research area because the joints are often the weakest areas in composite structures. This paper presents an analytical study of the stress distributions in mechanically single-fastened and multi-fastened composite laminates. The finite element models which treat the pin and hole contact problem using a contact stress analysis are described. A dimensionless stress concentration factor is used to compare the stress distributions in composite laminates quantitatively In the case of single-pin loaded composite laminate, the effects of stacking sequence, the ratio of a hole diameter and the width of a laminate (W/D ratio), the ratio of hole diameter and distance from edge to hole (E/D ratio), friction coefficient and clamping force are considered. In the case of multi-pin loaded composite laminate, the influence of the number of pins, pitch distance, number of rows, row spacing and hole pattern are considered. The results show that P/D ratio and E/D ratio affect more on stress distributions near the hole boundary than the other factors. In the case of multi-pin loaded composite laminate, the stress concentration in the double column case is better than the other cases of multi-pin loaded composite laminate.