• Title/Summary/Keyword: 점착

Search Result 1,176, Processing Time 0.026 seconds

Numerical Analyses for Evaluating Factors which Influence the Behavioral Characteristics of Side of Rock Socketed Drilled Shafts (암반에 근입된 현장타설말뚝의 주면부 거동에 영향을 미치는 변수분석을 위한 수치해석)

  • Lee, Hyuk-Jin;Kim, Hong-Taek
    • KSCE Journal of Civil and Environmental Engineering Research
    • /
    • v.26 no.6C
    • /
    • pp.395-406
    • /
    • 2006
  • Drilled shafts are a common foundation solution for large concentrated loads. Such piles are generally constructed by drilling through softer soils into rock and the section of the shaft which is drilled through rock contributes most of the load bearing capacity. Drilled shafts derive their bearing capacity from both shaft and base resistance components. The length and diameter of the rock socket must be sufficient to carry the loads imposed on the pile safely without excessive settlements. The base resistance component can contribute significantly to the ultimate capacity of the pile. However, the shaft resistance is typically mobilized at considerably smaller pile movements than that of the base. In addition, the base response can be adversely affected by any debris that is left in the bottom of the socket. The reliability of base response therefore depends on the use of a construction and inspection technique which leaves the socket free of debris. This may be difficult and costly to achieve, particularly in deep sockets, which are often drilled under water or drilling slurry. As a consequence of these factors, shaft resistance generally dominates pile performance at working loads. The efforts to improve the prediction of drilled shaft performance are therefore primarily concerned with the complex mechanisms of shaft resistance development. The shaft resistance only is concerned in this study. The nature of the interface between the concrete pile shaft and the surrounding rock is critically important to the performance of the pile, and is heavily influenced by the construction practices. In this study, the influences of asperity characteristics such as the heights and angles, the strength characteristics and elastic constants of surrounding rock masses and the depth and length of rock socket, et. al. on the shaft resistance of drilled shafts are investigated from elasto-plastic analyses( FLAC). Through the parametric studies, among the parameters, the vertical stress on the top layer of socket, the height of asperity and cohesion and poison's ratio of rock masses are major influence factors on the unit peak shaft resistance.

Egg Development and Morphology of Larva and Juvenile of Liparis tanakae in the Coastal Waters off Yeosu (여수 연안산 꼼치(Liparis tanakae)의 난발생 및 자치어 형태발달)

  • Kyung-Ae Jung;Na-Young Jeon;Sang-Hun Cha;Sung-Hoon Lee;Tae-Sik Yu;Keong-Ho Han
    • Korean Journal of Ichthyology
    • /
    • v.35 no.4
    • /
    • pp.263-269
    • /
    • 2023
  • This study aims to contribute to the research on resource recovery for the rapidly declining population of Liparis tanakae by observing the larval development process and the morphology of juveniles based on their growth. Natural spawning eggs collected in Yeosu were used for observing the process of egg development and larval morphology. The water temperature during the rearing process was maintained at 12.3~13.5℃ (average 12.7℃). The fertilized eggs had an egg diameter ranging from 1.57 to 1.79 mm (average 1.71 mm) and were spherical and adhesive. Within 4 hours 35 minutes after fertilization, they reached the two-cell stage, and after 74 hours 10 minutes, the formation of the yolk sac began. At 106 hours post-fertilization, a caudal fin appeared at the tail tip. Hatching began at 526 hours, and the larvae developed with the yolk sac positioned just behind the eyes. The newly hatched larvae had both the mouth and anus open. Melanophores appeared inside the lower jaw and around the tail on the third day after hatching. By the 16th day after hatching, most of the yolk was absorbed, and melanophores were visible in the head region. Finally, on the 63rd day after hatching, the head region significantly developed, and the body shape and mouth were similar to those of an adult fish, signifying the transition to the juvenile stage. This study will serve as valuable data for aquaculture techniques related to the conservation and restoration of fish species based on the hatching and juvenile morphology of Liparis tanakae.

The Effects of Environment-Friendly Agricultural Materials on Soil and the Quality of 'Niitaka' pear's Orchad (친환경농자재 처리가 배과수원 토양 및 과실품질에 미치는 영향)

  • Yoon, Seong-Tak;Xu, Zhen-Yu;Zhang, Qing-Yu;Kim, Tae-Ho;Nam, Jung-Chang;Park, Sang-Hun;Kwak, No-Il;Mun, Su-Hak;Lee, Hyuk-Jae;Choi, Jin-Ho
    • Korean Journal of Organic Agriculture
    • /
    • v.18 no.4
    • /
    • pp.613-626
    • /
    • 2010
  • Coming with the well-being era, consumer's demand for safe agricultural products is increasing. It is urgent to develop an environment-friendly pear production system. Accordingly, this study was conducted to develop an environment-friendly pear production system by using several environment-friendly agricultural materials which is known to be effective in agricultural production. In the effects of environment-friendly agricultural materials on the soil chemical characteristics in pear orchard, the content of total carbon, organic matter, Ca and Mg increased a little respectively compared with those of 2008, and 2nd treatment showed the highest EC and Mg content in the soil among treatments. The content of leaf N, P and Ca in 2009 decreased compared with those of 2008, while Mg content showed no difference between 2008 and 2009 years. Average pear weight in 2009 was 31g higher than that of 2008 (682g) and 2nd treatment showed the highest pear weight (738g) among treatments. The average sugar content was higher in 2009 (12.6$^{\circ}Bx$) compared with that of 2008 (12.2$^{\circ}Bx$) and the plot of 2nd treatment highest sugar content (12.6$^{\circ}Bx$) among treatments. There were no difference in hunter value of L among treatments, but hunter value of a showed higher 1.62 in 2009 than that of 2008 (3.73). The highest of gumminess and cohesiveness of fruits were obtained from 1st treatment and adhesiveness and chewiness of fruits were obtained from 3rd and 1st treatment respectively. Firmness of fruit increased a little in 2009 compared with that of 2008, while the highest firmness was obtained from 3rd treatment with 1.63kg/5mm$\oint$ among treatments. Phosphate content in the peel of 'Niitaka' pear of fruit skin in 2009 (0.97g/kg) showed 0.06g/kg more content than that of 2008 (0.91g/kg), while the highest content was obtained from 3rd treatment (1.15g/kg). Potassium content in the peel of 'Niitaka' pear in 2009 was 8.20g/kg, which is 0.06g/kg more content than that of 2008 (7.82g/kg) and the highest content was obtained from 1st treatment (8.34g/kg) among treatments. The highest nitrogen content in the flesh of 'Niitaka' pear was obtained from 3rd treatment (4.32mg/g), while it was the lowest in control plot (3.10mg/g). Phosphate content in the flesh of 'Niitaka' pear in 2009 (8.20g/kg) showed 0.06g/kg more content than that of 2008 (7.82g/kg), while the highest content was obtained from 1st treatment (8.34g/kg). There were no difference of the potassium content in the fruit peel of 'Niitaka' pear between years, but 1st treatment showed the highest content (11.81g/kg) among treatments, while the lowest was obtained from the control plot (10.83g/kg).

A Study on Estimating Shear Strength of Continuum Rock Slope (연속체 암반비탈면의 강도정수 산정 연구)

  • Kim, Hyung-Min;Lee, Su-gon;Lee, Byok-Kyu;Woo, Jae-Gyung;Hur, Ik;Lee, Jun-Ki
    • Journal of the Korean Geotechnical Society
    • /
    • v.35 no.5
    • /
    • pp.5-19
    • /
    • 2019
  • Considering the natural phenomenon in which steep slopes ($65^{\circ}{\sim}85^{\circ}$) consisting of rock mass remain stable for decades, slopes steeper than 1:0.5 (the standard of slope angle for blast rock) may be applied in geotechnical conditions which are similar to those above at the design and initial construction stages. In the process of analysing the stability of a good to fair continuum rock slope that can be designed as a steep slope, a general method of estimating rock mass strength properties from design practice perspective was required. Practical and genealized engineering methods of determining the properties of a rock mass are important for a good continuum rock slope that can be designed as a steep slope. The Genealized Hoek-Brown (H-B) failure criterion and GSI (Geological Strength Index), which were revised and supplemented by Hoek et al. (2002), were assessed as rock mass characterization systems fully taking into account the effects of discontinuities, and were widely utilized as a method for calculating equivalent Mohr-Coulomb shear strength (balancing the areas) according to stress changes. The concept of calculating equivalent M-C shear strength according to the change of confining stress range was proposed, and on a slope, the equivalent shear strength changes sensitively with changes in the maximum confining stress (${{\sigma}^{\prime}}_{3max}$ or normal stress), making it difficult to use it in practical design. In this study, the method of estimating the strength properties (an iso-angle division method) that can be applied universally within the maximum confining stress range for a good to fair continuum rock mass slope is proposed by applying the H-B failure criterion. In order to assess the validity and applicability of the proposed method of estimating the shear strength (A), the rock slope, which is a study object, was selected as the type of rock (igneous, metamorphic, sedimentary) on the steep slope near the existing working design site. It is compared and analyzed with the equivalent M-C shear strength (balancing the areas) proposed by Hoek. The equivalent M-C shear strength of the balancing the areas method and iso-angle division method was estimated using the RocLab program (geotechnical properties calculation software based on the H-B failure criterion (2002)) by using the basic data of the laboratory rock triaxial compression test at the existing working design site and the face mapping of discontinuities on the rock slope of study area. The calculated equivalent M-C shear strength of the balancing the areas method was interlinked to show very large or small cohesion and internal friction angles (generally, greater than $45^{\circ}$). The equivalent M-C shear strength of the iso-angle division is in-between the equivalent M-C shear properties of the balancing the areas, and the internal friction angles show a range of $30^{\circ}$ to $42^{\circ}$. We compared and analyzed the shear strength (A) of the iso-angle division method at the study area with the shear strength (B) of the existing working design site with similar or the same grade RMR each other. The application of the proposed iso-angle division method was indirectly evaluated through the results of the stability analysis (limit equilibrium analysis and finite element analysis) applied with these the strength properties. The difference between A and B of the shear strength is about 10%. LEM results (in wet condition) showed that Fs (A) = 14.08~58.22 (average 32.9) and Fs (B) = 18.39~60.04 (average 32.2), which were similar in accordance with the same rock types. As a result of FEM, displacement (A) = 0.13~0.65 mm (average 0.27 mm) and displacement (B) = 0.14~1.07 mm (average 0.37 mm). Using the GSI and Hoek-Brown failure criterion, the significant result could be identified in the application evaluation. Therefore, the strength properties of rock mass estimated by the iso-angle division method could be applied with practical shear strength.

홍삼 유래 성분들의 면역조절 효능

  • Jo, Jae-Yeol
    • Food preservation and processing industry
    • /
    • v.8 no.2
    • /
    • pp.6-12
    • /
    • 2009
  • 면역반응은 외부 감염원으로부터 신체를 보호하고 외부감염원을 제거하고자 하는 주요항상성 유지기전의 하나이다. 이들 반응은 골수에서 생성되고 비장, 흉선 및 임파절 등에서 성숙되는 면역세포들에 의해 매개된다. 보통 태어나면서부터 얻어진 선천성 면역반응을 매개하는 대식세포, 수지상 세포 등과, 오랜기간 동안 감염된 다양한 면역원에 대한 경험을 토대로 얻어진 획득성 면역을 담당하는 T 임파구 등이 대표적인 면역세포로 알려져 있다. 다양한 면역질환이 최근 주요 사망률의 원인이 되고 있다. 최근, 암, 당뇨 및 뇌혈관질환 등이 생체에서 발생되는 급 만성염증에 의해 발생된다고 보고됨에 따라 면역세포 매개성 염증질환에 대한 치료제 개발을 서두르고 있다. 또한 암환자의 급격한 증가는 암발생의 주요 방어기전인 면역력 증강에 대한 요구들을 가중시키고 있다. 예로부터 사용되어 오던 고려인삼과 홍삼은 기를 보호하고 원기를 회복하는 명약으로 알려진 대표적인 우리나라 천연생약이다. 특별히, 홍삼은 단백질과 핵산의 합성을 촉진시키고, 조혈작용, 간기능 회복, 혈당강하, 운동수행 능력증대, 기억력 개선, 항피로작용 및 면역력 증대에 매우 효과가 좋은 것으로 보고되고 있다. 홍삼에 관한 많은 연구에 비해, 현재까지 홍삼이 면역력 증강에 미치는 효과에 대한 분자적 수준에서의 연구는 매우 미미한 것으로 확인되어져 있다. 홍삼의 투여는 NK 세포나 대식세포의 활성이 증가하고 항암제의 암세포 사멸을 증가시키는 것으로 확인되어졌다. 현재까지 알려진 주요 면역증강 성분은 산성다당류로 보고되었다. 또 한편으로 일부 진세노사이드류에서 항염증 효능이 확인되어졌으며, 이를 통해 피부염증 반응과 관절염에 대한 치료 효과가 있는 것으로 추측되고 있다 [본 연구는 KT&G 연구출연금 (2009-2010) 지원을 받아 이루어졌기에 이에 감사드린다]. 면역반응은 외부 감염물질의 침입으로 유도된 질병환경을 제거하고 수복하는 중요한 생체적 방어작용의 하나이다. 이들 과정은 체내로 유입된 미생물이나 미세화학물질들과 같은 독성물질을 소거하거나 파괴하는 것을 주요 역할로 한다. 외부로 부터 인체에 들어온 이물질에 대한 방어기전은 현재 두 가지 종류의 면역반응으로 구분해서 설명한다. 즉, 선천성 면역 반응 (innate immunity)과 후천성 면역 반응 (adaptive immunity)이 그것이다. 선천성 면역반응은 1) 피부나 점막의 표면과 같은 해부학적인 보호벽 구조와 2) 체온과 낮은 pH 및 chemical mediator (리소자임, collectin류) 등과 같은 생리적 방어구조, 3) phagocyte류 (대식세포, 수지상세포 및 호중구 등)에 의한 phagocytic/endocytic 방어, 그리고 4) 마지막으로 염증반응을 통한 감염에 저항하는 면역반응 등으로 구분된다. 후천성 면역반응은 획득성면역이라고도 불리고 특이성, 다양성, 기억 및 자기/비자기의 인식이라는 네 가지의 특징을 가지고 있으며, 외부 유입물질을 제거하는 반응에 따라 체액성 면역 반응 (humoral immune response)과 세포성 면역반응 (cell-mediated immune response)으로 구분된다. 체액성 면역은 침입한 항원의 구조 특이적으로 생성된 B cell 유래 항체와의 반응과 간이나 대식세포 등에서 합성되어 분비된 혈청내 보체 등에 의해 매개되는 반응으로 구성되어 있다. 세포성 면역반응은 T helper cell (CD4+), cytotoxic T cell (CD8+), B cell 및antigen presenting cell 중개를 통한 세포간 상호 작용에 의해 발생되는 면역반응이다. 선천성 면역반응의 하나인 염증은 우리 몸에서 가장 빈번히 발생되고 있는 방어작용의 하나이다. 예를 들면 감기에 걸렸을 경우, 환자의 편도선내 대식세포나 수지상세포류는 감염된 바이러스 단독 혹은 동시에 감염된 박테리아를 상대로 다양한 염증성 반응을 유도하게 된다. 또한, 상처가 생겼을 경우에도 감염원을 통해 유입된 병원성 세균과 주위조직내 선천성 면역담당 세포들 간의 면역학적 전투가 발생되게 된다. 이들 과정을 통해, 주위 세포나 조직이 손상되면, 즉각적으로 이들 면역세포들 (주로 phagocytes류)은 신속하게 손상을 극소화하고 더 나가서 손상된 부위를 원상으로 회복시키려는 일련의 염증반응을 유도하게 된다. 이들 반응은 우리가 흔히 알고 있는 발적 (redness), 부종 (swelling), 발열 (heat), 통증 (pain) 등의 증상으로 나타나게 된다. 즉, 손상된 부위 주변에 존재하는 모세혈관에 흐르는 혈류의 양이 증가하면서 혈관의 직경이 늘어나게 되고, 이로 인한 조직의 홍반과, 부어 오른 혈관에 의해 발열과 부종이 초래되는 것이다. 확장된 모세혈관의 투과성 증가는 체액과 세포들이 혈관에서 조직으로 이동하게 하는 원동력이 되고, 이를 통해 축적된 삼출물들은 단백질의 농도를 높여, 최종적으로 혈관에 존재하는 체액들이 조직으로 더 많이 이동되도록 유도하여 부종을 형성시킨다. 마지막으로 혈관 내 존재하는 면역세포들은 혈판 내벽에 점착되고 (margination), 혈관벽의 간극을 넓히는 역할을 하는 히스타민 (histamine)이나 일산화질소(nitric oxide : NO), 프로스타그린딘 (prostagladins : PGE2) 및 류코트리엔 (leukotriens) 등과 같은 chemical mediator의 도움으로 인해 혈관벽 사이로 삼출하게 되어 (extravasation), 손상된 부위로 이동하여 직접적인 외부 침입 물질의 파괴나 다른 면역세포들을 모으기 위한 cytokine (tumor necrosis factor [TNF]-$\alpha$, interleukin [IL]-1, IL-6 등) 혹은 chemokine (MIP-l, IL-8, MCP-l등)의 분비 등을 수행함으로써 염증반응을 매개하게 된다. 염증과정시 발생되는 여러 mediator 중 PGE2나 NO 및 TNF-$\alpha$ 등은 실험적 평가가 용이하여 이들 mediator 자체나 생성관련효소 (cyclooxygenase [COX] 및 nitric oxide synthase [NOS] 등)들은 현재항염증 치료제의 개발 연구시 주요 표적으로 연구되고 있다. 염증 반응은 지속기간에 따라 크게 급성염증과 만성염증으로 나뉘며, 삼출물의 종류에 따라서는 장액성, 섬유소성, 화농성 및 출혈성 염증 등으로 구분된다. 급성 염증 (acute inflammation)반응은 수일 내지 수주간 지속되는 일반적인 염증반응이라고 볼 수 있다. 국소반응은 기본징후인 발열과 발적, 부종, 통증 및 기능 상실이 특징적이며, 현미경적 소견으로는 혈관성 변화와 삼출물 형성이 주 작용이므로 일명 삼출성 염증이라고 한다. 만성 염증 (chronic inflammation)은, 급성 염증으로부터 이행되거나 만성으로 시작된다. 염증지속 기간은 보통 4주 이상 장기화 된다. 보통 염증의 경우에는 염증 생성 cytokine인 Th1 cytokine (IL-2, interferone [IFN]-$\gamma$ 및 TNF-$\alpha$ 등)의 생성 후, 거의 즉각적으로 항 염증성 cytokine인 Th2 cytokine(IL-4, IL-6, IL-10 및 transforming growth factor [TGF]-$\beta$ 등)이 생성되어 정상반응으로 회복된다. 그러나, 어떤 원인에서든 면역세포에 의한 염증원 제거 반응이 문제가 되면, 만성염증으로 진행된다. 이 반응에 주로 작용을 하는 염증세포로는 단핵구와 대식세포, 림프구, 형질세포 등이 있다. 암은 전세계적으로 사망률 1위의 원인이 되는 면역질환의 하나이다. 산화적 스트레스나 자외선 조사 혹은 암유발 물질들에 의해 염색체내 protooncogene, tumor-suppressor gene 혹은 DNA repairing gene의 일부 DNA의 돌연변이 혹은 결손 등이 발행되면 정상세포는 암화과정을 시작하게 된다. 양성세포 수준에서 약 5에서 10여년 후 악성수준의 암세포가 생성되게 되면 이들 세포는 새로운 환경을 찾아 전이하게 되는데 이를 통해 암환자들은 다양한 장기에 동인 오리진의 암세포들이 생성한 종양들을 가지게 된다. 이들 종양세포는 정상 장기의 기능을 손상시켜며 결국 생명을 잃게 만든다. 이들 염색체 수준에서의 돌연변이 유래 암세포는 거의 대부분이 체내 면역시스템에 의해 사멸되는 것으로 알려져 있다. 그러나 계속되는 스트레스나 암유발 물질의 노출은 체내 면역체계를 파괴하면서 최후의 방어선을 무너뜨리면서 암발생에 무방비 상태를 만들게 된다. 이런 이유로 체내 면역시스템의 정상적 가동 및 증강을 유도하게 하는 전략이 암예방시 매우 중요한 표적으로 인식되면서 다양한 형태의 면역증강 물질 개발을 시도하고 있다. 인삼은 두릅나무과의 여러해살이 풀로써, 오랜동안 한방 및 민간에서 원기를 회복시키고, 각종 질병을 치료할 수단으로 사용되고 있는 대표적인 전통생약이다. 예로부터 불로(不老), 장생(長生), 익기(益氣), 경신(經身)의 명약으로 구전되어졌는데, 이는 약 2천년 전 중국의 신농본초경(神農本草經)에서 "인삼은 오장(五腸)을 보하고, 정신을 안정시키고, 혼백을 고정하며 경계를 멈추게 하고, 외부로부터 침입하는 병사를 제거하여주며, 눈을 밝게 하고 마음을 열어 더욱 지혜롭게 하고 오랫동안 복용하면 몸이 가벼워지고 장수한다" 라고 기술되어있는 데에서 유래한 것이다. 다양한 연구를 통해 우리나라에서 생산되는 고려인삼 (Panax ginseng)이 효능 면에서 가장 탁월한 것으로 알려져 있으며 특별이 고려인삼으로부터 제조된 고려홍삼은 전세계적으로도 그 효능이 우수한 것으로 보고되어 있다. 대부분의 홍삼 약효는 dammarane계열의 triterpenoid인 ginsenosides라고 불리는 인삼 saponin에 의해 기인된 것으로 알려져 있다. 이들 화합물군의 기본 골격에 따라, protopanaxadiol (PD)계 (22종) 및 protopanaxatriol (PT)계 (10종)으로 구분되고 있다 (표 1). 실험적 접근을 통해 인삼의 약리작용 이해를 위한 다양한 노력들이 경주되고 있으나, 여전히 많은 부분에서 충분히 이해되고 있지 않다. 그러나, 현재까지 연구된 인삼의 약리작용 관련 연구들은 심혈관, 당뇨, 항암 및 항스트레스 등과 같은 분야에서 인삼효능이 우수한 것으로 보고하고 있다. 그러나 면역조절 및 염증현상과 관련된 최근 연구결과들은 많지 않으나, 향후 다양하게 연구될 효능부분으로 인식되고 있다.

  • PDF

Physico-Chemical Properties of Aggregate By-Products as Artificial Soil Materials (골재 부산물의 용토재 활용을 위한 특성 분석)

  • Yang, Su-Chan;Jung, Yeong-Sang;Kim, Dong-Wook;Shim, Gyu-Seop
    • Korean Journal of Soil Science and Fertilizer
    • /
    • v.40 no.5
    • /
    • pp.418-428
    • /
    • 2007
  • Physical and chemical properties of the aggregate by-products including sludge and crushed dust samples collected from the 21 private companies throughout the country were analyzed to evaluate possible usage of the by-products as artificial soil materials for plantation. The pH of the materials ranged from 8.0 to 11.0. The organic matter content was $2.85g\;kg^{-1}$, and the total nitrogen content and available phosphate content were low as 0.7 percents and $12.98mg\;kg^{-1}$, respectively. Exchangeable $Ca^{2+}$, $Mg^{2+}$, $K^+$, and $Na^+$ were 2.29, 0.47, 0.02 and $0.05cmol\;kg^{-1}$, respectively. Heavy metal contents were lower than the limits regulated by environmental law of Korea. Textural analysis showed that most of the materials were silt loam with low water holding capacity ranged from 0.67 to 7.41 percents, and with low hydraulic conductivity ranged from 0.4 to $2.8m\;s^{-1}$. Mineralogical analysis showed that the aggregate by product materials were mostly composed of silicate, alumina and ferric oxides except calcium oxide dominant materials derived from limestones. The primary minerals were quartz, feldspars and dolomites derived from granite and granitic gneiss materials. Some samples derived from limestone material showed calcite and graphite together with the above minerals. According to the result, it can be concluded that the materials could be used as the artificial soil material for plantation after proper improvement of the physico-chemical properties and fertility.