• Geotechnical Engineering
• /
• v.12 no.3
• /
• pp.109-126
• /
• 1996

In this study, the chemical fluid considered is sodium chloride sloutions. The concentrations for the sodium chloride solutions are varied from 0 to 20%. A series of lab oratory triaxial tests are performed on the cylindrical specimens of sand bentonite mixture with different (5, 10, 15%) sodium chloride content solutions. Deformation(elastic modulus, E) and strength (cohesion, c', and angle of friction, f') parameters are obtained from the triaxial tests and they are expressed as functions of conf'ming pressure and sodium chloride solution concentrations. The stress-strain-strength behavior based on the above strength parameters is introduced to the finite element method with a residual flow procedure (RFP). By integrating a slope stability (limit equilibrium) procedure in the finite element method, factors of safety with time are computed.

• Geotechnical Engineering
• /
• v.9 no.3
• /
• pp.5-22
• /
• 1993

A series of laboratory tests (physical and mechanical index and engineering design) were conducted on undisturbed granite soils of CW and RS weathering grades in Korea. From these testes it can be concluded that most of physical and mechanical index values are very sensitive to change in weathering grade from CW to RS. Engineering design tests indicate that the unconfined compressive strength and the shear strength parameters are significantly reduced and that the soil becomes ductile and plastic with increasing weathering and saturation. It was found that weathered granite soils have the special characteristics when water saturated: (i) they significantly lose their shear strength(especially cohesion) and unconfined compressive strength, (ii) they are fragile and their grains break down in water as observed in grain size analysis.

• The Journal of Engineering Geology
• /
• v.25 no.2
• /
• pp.189-199
• /
• 2015

Our country's leading granite weathered soil of the ground slope failures that occur in cutting slope most cases, it does not require in-depth to the shear strength most of the surface layer is affected by weathering (1~2 m) at a shallow depth close to the ground, it is important to identify the reliability. Based on the result obtained in actual field investigation, the field slope type was classified by each type of wedge slope, Infinite slope, finite slope -I and finite slope -II, and the slope stability was examined respectively. In addition, using the numerical analysis results, the relationship between the slope inclination angle and safety factor was analyzed and it tried to offer basic data to which the stability in the field slope was able to be estimated by analyzing the safety factor change of the slope according to the slope type. In this study, classified into four types of natural slope, safety factor estimation method by slope types is proposed through the numerical analysis. However, some limit exists in generalizing in this research because it does not test various case studies. Therefore, the case study of a wide range of various sypes to assess the safety of various types slope can be made, accommodate a wide range of field conditions reasonable risk evaluation criteria may be derived.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.8 no.1
• /
• pp.25-32
• /
• 2013

This study has been conducted in order to propose Eco-friendly and High functional waterproofing technology available for structure by verifying application and performance of water proofing material(s) in purpose of making effective use of reclaimed rubber. As s result of 12 months evaluation, stable performance for water pressure and lateral pressure of $0.3N/mm^2$ were confirmed. Also, as the time elapsed, the amount of water absorption and adhesion performance showed only a slight difference(+0.05g, $-0.1Nmm^2$) as well, which in turn confirmed that waterproofing performance remains stable. Studies show that it is expected to expand recycling technology of natural rubber by applying reclaimed rubber on construction waterproofing field, and to hold a technical superiority by using eco-friendly material in construction waterproofing market throughout active application of these types of research.

• Elastomers and Composites
• /
• v.49 no.1
• /
• pp.43-52
• /
• 2014

The effect of nanoclay (Cloisite 20A) on the self-adhesion behavior of uncured brominated-isobutylene-isoprene rubber (BIIR) has been studied. The dispersion state of nanoclay into the rubber matrix was examined by SEM, TEM and XRD analysis. The thermal degradation behavior of the filled and unfilled samples was examined by TGA and improvement in the thermal stability of the nanocomposites occurred based on the weight loss (%) measurements. Also, addition of nanoclay enhanced the cohesive strength of the material by reinforcement action thereby reducing the degree of molecular diffusion across the interface of butyl rubber. However, the average depth of penetration of the inter-diffused chains was still adequate to form entanglement on either side of the interface, and thus offered greater resistance to peeling, resulting in high tack strength measurements. The improvement in tack strength was only achieved at critical nanoclay loading above 8 phr. Contact angle measurement was also made to examine the surface characteristics. There was no significant interfacial property change by employing the nanoclay.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.10
• /
• pp.331-337
• /
• 2016

Several foundation soil conditions below a homogeneous sand slope were assumed and slope stability analyses were conducted to determine the soil condition, in which a stabilizing pile can be used to increase the factor of safety against sliding. The assumed heights of the sand slope were 5m and 10m. For a 5m slope height, a stabilizing pile can be used in the foundation soil with a $15^{\circ}$ internal friction angle and a cohesion of 10kPa. For a 10m slope height, a stabilizing pile can be used in the foundation soil with a $20^{\circ}$ internal friction angle and a cohesion of 10kPa and a stabilizing pile can be used in the foundation soil with a $0^{\circ}$ internal friction angle and 40kPa, 45kPa and 50kPa of cohesion. According to the analysis results of stabilizing pile-reinforced foundation soil, the length of the stabilizing pile and magnitude of the maximum bending moment were strongly affected by the internal friction angle of the foundation soil. The lengths of stabilizing pile, for an internal friction angle of $0^{\circ}$ were 4.6, 8.0 times greater than those with an internal friction angle of $5^{\circ}$. The magnitude of the maximum bending moment of the stabilizing pile for an internal friction angle of $0^{\circ}$ was 24.6 times greater than that for an internal friction angle of $5^{\circ}$. Practically, a stabilizing pile cannot be used for foundation soil with an internal friction angle of $0^{\circ}$. Considering the results derived from this study, the effects of a stabilizing pile can be maximized for soft foundation soil that is embanked with a slow construction speed.

• Korean Journal of Agricultural Science
• /
• v.5 no.1
• /
• pp.15-28
• /
• 1978

It has been known that the shear strength of soil is an important design parameter for the foundation of structures, the retaining walls, the slope failures and so forth. In this study, the shear test was performed by using the direct shear apparatus under various degree of the moisture content and the density of the sample soils. The results of the study were summarized as follows; 1. The shear strength of soil increased with increase in the dry density of soil, and at the same level of density of the sample the shear strength of soil showed large values on a good grading of the sample. 2. The cohesion of the soil varied directly with the dry density of it, however the internal friction angle of soil was not affected by the dry density of tile sample. 3. The shear strength of sample varied inversly with the moisture content of it, and this phenomenon was apparent on a good grad ing of sample. 4. The cohesion of soil showed maximum value when the moisture content of the soil reached optimum level and the internal friction angle decreased with increase in the moisture content of it. These phenomena were very obvious on a good grading sample, SDC-1. 5. The cohesion of the soil decreased with increase in void ratio of the sample, but the internal friction angle of the sample didn't show such tendency.

• Journal of the Korean GEO-environmental Society
• /
• v.7 no.5
• /
• pp.31-39
• /
• 2006

In this study, modified triaxial compression tests were carried out to investigate the characteristics of shear strength of unsaturated dredged soils. The variation of shear strength generally depends on more matric suction than drained conditions, and then is gradually converged in matric suction 100kPa. It indicates that the effective angle of internal friction and effective cohesion in unsaturated conditions increase due to degree of saturation, namely, matric suction than those of saturated conditions. Therefore, it shows that apparent friction angle, ${\phi}^b$ due to the variation of matric suction to evaluate reasonable shear strength parameters in unsaturated soils should be considered.

• Journal of the Korean Geosynthetics Society
• /
• v.8 no.4
• /
• pp.27-34
• /
• 2009

In this paper, characteristics of shear strength and deformation of geosynthetics-reinforced slag materials are described. In order to investigate the effect of geosynthetics on shear strength and deformation behavior of slags, when they are reinforced with geosynthetics or geomat such as PET mat, large triaxial tests were performed under consolidated-drained condition. The materials used in the study are real ones as they are in the field, so that the scale effect of samples disappeared. From the large triaxial tests, it was observed that the stress-strain relationship of geosynthetics-reinforced slags shows relatively small dilatancy and weak tendency of strain hardening, compared with that of slags without reinforcement. The shear strength parameters such as apparent cohesion and internal friction angle increase with PET mat reinforcement, consequently result in about 1.2 (for low confining pressure) to 1.4 (for high confining pressure) times of shear strength of un-reinforced sample. Therefore, the adoption of geomat-reinforced slag layers leads to an increase in the factor of safety for embankment design on soft soil formations.

• Korean Journal of Food Science and Technology
• /
• v.24 no.2
• /
• pp.160-164
• /
• 1992

Cooking, texture and sensory properties of sweet potato Tangmyon (starch noodle), common Tangmyon (50% sweet potato starch+50% corn starch) and corn Tangmyon were evaluated. The weight gain of Tangmyon showed a linear relationship with the square root of cooking time, in which the common Tangmyon showed the highest value. The solid loss during cooking was the highest in common Tangmyon followed by corn Tangmyon. The sweet potato Tangmyon showed the highest value for compression strength and stretching ratio, but lowest value for elongation elastic modulus. At the same compression strength, corn Tangmyon had the highest tensile strength and sweet potato Tangmyon the lowest value. Sweet potato Tangmyon showed the highest sensory scores of gloss, clarity, adhesiveness, gumminess, extensibility and overall desirability, and corn Tangmyon the lowest scores. Except adhesiveness (by appearance) and the gumminess of common and corn Tangmyon, significant differences (p<0.05) were observed for other sensory properties among samples.