• Journal of Korean Tunnelling and Underground Space Association
• /
• v.24 no.5
• /
• pp.395-409
• /
• 2022

To overcome the limitation of conventional rock excavation methods, the excavation with abrasive waterjet has been actively developed. The abrasive waterjet excavation method has the effect of reducing blasting vibration and enhancing the excavation efficiency by forming a continuous free surface on the rock. However, the waterjet cutting performance varies with rock fracturing characteristics. Thus, it is necessary to analyze the cutting performance for various rocks in order to effectively utilize the waterjet excavation. In this study, cutting experiments with the high pressure waterjet system were performed for basalt and granite specimens. Water pressure, standoff distance, and traverse speed were determined as effective parameters for the abrasive waterjet cutting. The cutting depth and width of basalt specimens were analyzed to compare with granite results. The averaged cutting depth of basalt was shown in 41% deeper than granite; in addition, the averaged cutting width of basalt was formed by 18.5% narrower than granite. The results of this study are expected to be useful basic data for applying rock excavation site with low strength and high porosity such as basalt.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.10 no.6
• /
• pp.807-813
• /
• 1986

The orthogonal cutting method of the nodular graphite cast iron in the lathe turning, whose matrix were formulated under two kinds of annealing conditions, has been experimentally studied and the results investigated. The various characteristics of machinabilities of the nodular cast iron, depending upon its matrix, have been obtained from the results as follows. (1) As depth of cut increases, the cutting ratio and the shear angles tend to slightly increase, and as the containing quantity of ferrite matrix increases, they slightly decrease. (2) As depth of cut increases, the cutting force increases in an approximate straight line, and as the containing quantity of ferrite matrix increases, they decreases and the decreasing rate is about 20-30%. (3) As the containing quantity of ferrite matrix increases, the friction force acting on the tool face decreases and the decreasing rate is about 34-40% in case of the lower depth of cut, but in case of the higher depth of cut the decreasing rate is very small. (4) Both shearing force and vertical force show a lineal increases, and according as ferrite matrix increases there is a decrease by 25% in shearing force and a 12-25% decrease in vertical force. (5) Shearing speed and chip flow speed keep almost a constant value irrespective of matrix.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.11a
• /
• pp.129-130
• /
• 2010

• Clean Technology
• /
• v.8 no.3
• /
• pp.119-128
• /
• 2002

In the present study the membrane filtration characteristics of a commercially available synthetic water-based cutting oil through two kinds of ultrafiltration membranes (HF1-45-CM50 and HF1-43-CM100) with molecular weight cut-offs of 50,000 and 100,000, respectively, have been investigated in detail. Among these membranes, the hydrophilic one (HF1-45-CM50) was found to show a satisfactory result for both the permeate flux and the permeability of oil components, whereas the permeate flux obtained with the hydrophobic membrane (HF1-43-CM100) appears to be significantly low, indicating that synthetic cutting oil was easily wetted on the hydrophobic membrane surface and induced more membrane fouling. The effect of material characteristics of the membrane on the filtration characteristics was found to be much more significant compared with the mean pore size of the membrane. Backflushing by nitrogen gas was applied to reduce the formation of a gel layer and membrane fouling. With the hydrophilic membrane, the backflushing was found to increase the permeate flux, whereas the backflushing resulted in a decrease in flux for the hydrophobic membrane. The flux recovery was observed to be highest when the membranes fouled with waste synthetic cutting oil were immersed into a cleaning solution for more than 72 hours and then backflushed by nitrogen gas.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.8
• /
• pp.1480-1486
• /
• 2002

In this study, the cross-coupling control (CCC) with three new features is proposed to maintain contour precision in high-speed nonlinear contour machining. One is an improved contour error model that provides almost exact calculation of the errors. Another is the utilization of variable controller gains based on the instantaneous curvature of the contour and the variable command. For this scheme, a stability is analyzed. As a result, the stability region is obtained, and the variable gains are decided within that region. The other scheme in the proposed CCC is a real-time feedrate adaptation module to regulate cutting force fur better surface finish through regulation of material removal rate (MRR). The simulation results show that the proposed CCC system can provide better precision than the existing method particularly in high-speed machining of nonlinear contours.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.22 no.6
• /
• pp.1003-1009
• /
• 2013

This paper presents a simple procedure to obtain the instantaneous cutting force constants needed to predict milling forces. Cutting force data measured in a series of slot milling tests were used to determine the cutting force constants at different feed rates. The values of the cutting force constants were determined directly at the tool rotation angle that maximized the uncut chip thickness. Then, the instantaneous cutting force constant was obtained as a function of the instantaneous uncut chip thickness. This approach can greatly enhance the accuracy of the mechanistic cutting force model for end milling. In addition, the influences of several cutting parameters on the cutting forces, such as the tool helix angle and axial depth of cut, were discussed.

• 제어로봇시스템학회:학술대회논문집
• /
• 1991.10a
• /
• pp.809-814
• /
• 1991

기존의 CNC Controller를 재구성하면 제어성과 절삭성의 재고에 큰 효과를 낼 수 있다. 현실적으로 시스템의 재구성은, 가) 시스템의 재구성으로 2축 CNC 기계를 다축으로 전환시킬 수 있고, 나) 모터의 직접제어에 의한 G-code 작성과정의 생략이 가능하며, 다) NC 동작의 제어가 소프트웨어로 (C 언어) 이루어 지기 때문에 사용자환경에 맞도록 고객화가 가능한 강점이 있다. 나아가서는 형상의 정의에서 NC 기계동작의 제어 및 온라인 모니터링에 이르는 전과정을 소프트웨어로 일식화 시킬 수 있는 통합 NC 시스템의 구현이 가능하다. 본 논문에서는 이러한 목적으로 연구되고 있는 INCS(Integrated NC System)의 개발현황을 소개한다. INCS는 PC-286, NC Controller, Drive Amplifier, Sensing Device의 하드웨어 시스템과 CAD, CAM 및 CNC 기능을 수행하는 소프트웨어 시스템으로 구성되어 있다. 그래픽 시뮬레이션 및 실제 절삭을 통하여 개발된 방식의 유효성과 효율성을 설명한다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.985-988
• /
• 1997

In end milling process, the undeformed chip section area and cutting forces vary periodically with phase change of the tool. However the real undeformed chip section area deviates from the geometrically ideal one owing to cutter runout and tool shape error. In this study ,a method of estimating the real undeformed chip section area which reflects cutter runout and tool shape error was presented in up end milling process using measured cutting forces. Size effect was identified from the analysis of specific cutting resistance obtained by using the modified undeformed chip section area.

• Journal of the Korean Society for Precision Engineering
• /
• v.7 no.1
• /
• pp.53-62
• /
• 1990

High speed and heavy cutting performed for improving the surface quality and productivity, are often prevented due to chatter phenomena. Chatter is a violent relative vibration between workpiece and tool in machining of metals, and is an important limiting factor of production rate and surface quality, and reduces the tool life and the dynamic performance of machine tool itself. In this study, in order to suppress the chatter, a modified tool-post combined with the spring and damper was designed and used in the actual cutting test. The results of this study are summerized as follows; The spring and damper adopted in the modified tool-post have the suppressing effects of chatter, and there exists an optimum combination between spring constant and damping ratio.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.2
• /
• pp.292-301
• /
• 1994

The resultant cutting force during machining with a worn tool is viewed as a decomposition of the cutting force into a cutting force component related to chip removal from the workpiece and into a component dependent on the contact force between the tool flank's wear land and the workpiece. The shear line method, in which the cutting force is considered proportional to the length of the shear line, is used to calculate the cutting force component for the removal of the chip, while the elastic effect of the workmaterial on the tool is taken into consideration to analyze the effect of tool flank wear. The predicted resultant cutting force, expressed as the sum of both components, is compared to experimental data obtained during wave-on-wave cutting.