• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.18 no.10
• /
• pp.60-67
• /
• 2019

Recently, lightweight materials such as Ti alloys have been used increasingly in the aerospace and high-tech industries for weight loss and fuel efficiency. Because of built-up edges and workpiece deflection due to low stiffness, the Ti alloys have poor machinability. In our study, systematic experiments were conducted to investigate the milling characteristics of the Ti alloy (Ti-6A1-4V) with endmills. The independent variables in the experiment were spindle speed, feed per tooth, and axial depth. Cutting force, acceleration RMS, and surface roughness were measured. Using the response surface method, the optimal cutting conditions were analyzed to improve machining quality and productivity.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.4
• /
• pp.39-47
• /
• 2004

In mold machining, there are many concave machining regions where chatter and tool deflection occur since MRR(material removal rate) increases as curvature increases even though cutting speed and depth of cut are constant. Boolean operation between stock and tool model is widely used to compute MRR in NC milling simulation. In finish cutting, the side step is reduced to about 0.3mm and tool path length is sometimes over loom, so Boolean operation takes long computation time and includes much error if the resolution of stock and tool model is larger than the side step. In this paper, curvature of CL (cutter location) surface and side step of tool path is used to compute the feedrate for constant MRR machining. The data structure of CL surface is Z-map generated from NC tool path. The algorithm to get local curvature from discrete data was developed and applied to compute local curvature of CL surface. The side step of tool path was computed by point density map which includes cutter location point density at each grid element. The feedrate computed from curvature and side step is inserted to new tool path to regulate MRR. The resultants were applied to feedrate optimization system which generates new tool path with feedrate from NC codes for finish cutting. The system was applied to the machining of speaker and cellular phone mold. The finishing time was reduced to 12.6%, tool wear was reduced from 2mm to 1.1mm and chatter marks and over cut on corner were reduced, compared to the machining by constant feedrate. The machining time was shorter to 17% and surface quality and tool was also better than the conventional federate regulation using curvature of the tool path.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.16 no.6
• /
• pp.7-14
• /
• 2017

This study manufactured a minimum quantity lubrication (MQL) supply system and identified the optimal MQL machining cutting conditions for plastic mold steel (SCM440). A series of experiments were consisted of twice. Optimal cutting conditions were derived using the Taguchi method, and cutting force variance; surface roughness; tool wear; and cutting temperature in dry, wet, and MQL machining were measured experimentally for these optimal conditions. The measured results decreased from dry to wet and MQL machining, being particularly large for dry machining due to increased cutting time. Measured MQL machining metrics were similar to those for wet machining, particularly for surface roughness, which is an index of machining quality.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.22 no.4
• /
• pp.383-399
• /
• 2020

Optimizing the spacing of the disc cutter is a key element in the design of the TBM cutter head, which determines the drilling performance of the TBM. The full-scale linear cutting test is known as the most reliable and accurate test for calculating the spacing of the disc cutter, but it has the disadvantage of costly and time-consuming for the full-scale experiment. In this study, through the numerical analysis study based on the discrete element method, the tendency between Specific Energy-S/P ratio according to uniaxial compression strength and penetration depth of rock was analyzed, and the optimum spacing of 17-inch disc cutter was derived. To examine the appropriateness of the numerical analysis model, the rolling force acting on the disc cutter was compared and reviewed with the CSM model. As a result of numerical analysis for the linear cutting test, the rolling force acting on the disc cutter was analyzed to be similar to the rolling force derived from the theoretical formula of the CSM model. From the numerical analysis on 5 UCS cases (50 MPa, 70 MPa, 100 MPa, 150 MPa, 200 MPa), it is found that the range of the optimum spacing of the disc cutter decreases as the rock strength increases. And it can be concluded that 80~100 mm of disc cutter spacing is the optimum range having minimum specific energy regardless of rock strength. This tends to coincide with the optimal spacing of previously reported disk cutters, which underpins the disk cutter spacing calculated through this study.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.903-906
• /
• 1997

For the net shape manufacturing, grinding is a important process that influences directly the accuracy and the integrity of products. We studied and researched the grinding force, surface roughness, and grinding wheel durability, according to the change of a feed speed of the table and a depth of the cut step by step with experiment that it is used to WA wheel. Workpiece materials were used STDII. The purpose of this study proposes the basic data for design of the machine tool and for controlling the machining parameters to obtain optimum performance of plunge grinding system during operation.

• Proceedings of the Korean Operations and Management Science Society Conference
• /
• 2003.05a
• /
• pp.189-193
• /
• 2003

금형가공에 있어서 밀링머신의 가공에서는 절삭가공의 잔유물인 버(Burr)가 생성되고, 이러한 버는 가공의 정밀도를 감소시킬 뿐만 아니라 후처리과정(Deburring)을 야기시킴으로 인해서 작업효율의 감소 및 생산성의 비효율적 낭비를 가져오게 된다. 따라서, 정밀도와 작업효율을 극대화하긴 위해서는 버의 생성원리를 파악하고, Exit Burr의 생성부분을 미리 예측하여 버의 생성을 최소화 할 수 잇는 작업 가공계획을 설계하여야 한다. (1)기존의 Burr Exit System에서는 피삭재의 단면형상인 Line과 Are처럼 단순한 형상뿐만 아니라, Line과 Are가 연결되어있는 복잡란 형상에 대해서도 버를 판별한다. 그리고, 가공 후 버가 생성되는 부분을 예측하고, 이때의 Exit Angle을 계산하여 이에 해당하는 기 실험결과 DataBase와 연동하여 생설될 버의 형상과 크기 등의 결과를 제공하여 준다. 더불어, 피삭재의 단면형상이 여러 가지 복합적인 형상으로 이루어져 있는 경우와 다양한 공구 경로까지 고려하여 실제가공과 거의 유사란 상황을 적용할 수 잇는 알고리즘으로 개발하였다. 본 논문에서는 이제까지 개발된 다양한 형상에 대한 Exit Burr 판별 알고리즘을 이용하여 임의형상을 가진 피삭재의 다중가공경로 상에서 발생 가능한 버를 예측하고, 버의 길이나 가공시간 들을 정?화 하여 최적화하는데 필요란 요소를 추출해 보고자 한다. 또한, 이를 인용하여 Face Windows에서의 버의 발생을 최소화 할 수 있는 최적 절삭가공 공구경로를 제시하여, 작업 효율성을 극대화하는 알고리즘을 Windows 응용 프로그램으로 구현하고자 한다.생성하기보다는 기존에 발생된 구매 지시의 우선적 사용과 기존 구매 지시의 납기 일자를 고객 납기에 가장 잘 맞출 수 있도록 변경하는 방안을 제시한다. 이렇게 함으로써 최대한 고객 납기를 만족하도록 계획을 수립할 수 있게 된다. 본 논문에서 제시하는 계획 모델을 사용함으로써 고객 주문에 대한 대응력을 높일 수 있고, 계획의 투명성으로 인한 전체 공급망의Bullwhip effect를 감소시킬 수 있는 장점이 있다. 동시에 이것은 향후 e-Business 시스템 구축을 위한 기본 인프라 역할을 수행할 수 있게 된다. 많았고 년도에 따른 변화는 보이지 않았다. 스키손상의 발생빈도는 초기에 비하여 점차 감소하는 경향을 보였으며, 손상의 특성도 부위별, 연령별로 다양한 변화를 나타내었다.해가능성을 가진 균이 상당수 검출되므로 원료의 수송, 김치의 제조 및 유통과정에서 병원균에 대한 오염방지에 유의하여야 할 것이다. 확인할 수 있었다. 이상의 결과에 의하면 고농도의 유기물이 함유된 음식물쓰레기는 Hybrid Anaerobic Reactor (HAR)를 이용하여 HRT 30일 정도에서 충분히 직접 혐기성처리가 가능하며, 이때 발생된 $CH_{4}$를 회수하여 이용하면 대체에너지원으로 활용 가치가 높은 것으로 판단된다./207), $99.2\%$(238/240), $98.5\%$(133/135) 및 $100\%$ (313)였다. 각각 두 개의 요골동맥과 우내흉동맥에서 부분협착이나 경쟁혈류가 관찰되었다. 결론: 동맥 도관만을 이용한 Off pump CABG를 시행하여 감염의 위험성을