• 대한기계학회논문집
• /
• 제17권1호
• /
• pp.69-77
• /
• 1993

본 연구에서는 Koren과 Masory가 개발하여 적분제어기에 적용한 제어알고리즘 을, 제어기 반응속도를 향상시키기 위하여 비례적분제어기에 적용하는 방법을 제시하 고자 한다. 실험을 통하여 제어시스템을 모델링하고, 근궤적법을 이용하여 시스템을 안정하게 유지하기 위한 개회로 이득을 선정하며, 기존의 보통선반을 적응제어시스템 으로 개발하여 고정이득 비례적분제어기와 가변이득 비례적분제어기의 성능을 실험을 통하여 비교하고자 한다.

• 한국정밀공학회지
• /
• 제17권5호
• /
• pp.173-179
• /
• 2000

While a cutting tool is machining a workpiece at various cutting depth, the feedrate is usually selected based on the maximum depth of cut. Even if this selection can avoid power saturation or tool breakage, it is very conservative compared to the capacity of the machine tools and can reduce the productivity significantly. Many adaptive control techniques that can adjust the feedrate to maintain the constant cutting force have been reported. However, these controllers are not very widely used in manufacturing industry because of the limitations in measuring the cutting force signals. In this paper, turning force control systems based on the estimated cutting force signals are proposed. A synthesized cutting force monitor is introduced to estimate the cutting force as accurately as a dynamometer does. Three control strategies of PI, adaptive and fuzzy logic controllers are applied to investigate the feasibility of utilizing the estimated cutting force fur turning force control. The experimental results demonstrate that the proposed systems can be easily realized in CNC lathe with requiring little additional hardware.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 추계학술대회 논문집
• /
• pp.605-609
• /
• 1996

Continuous sliding mode control is applied to turning process for cutting force regulation. The highest feedrate compatible with the allowable cutting force is applied in rough cutting process such that maximum productivity is ensured and tool breakage is avoided. The programmed feedrate is overridden after the control algorithm is carried out. However, most CNC lathe manufacturers offer limited number of data bits far feedrate override, thus resulting in nonlinear behavior of the machine tools. Such nonlinearity brings “quantized” effect, and the optimal faedrate is rounded off before being fed into the CNC system. To compensate for this problem, continuous sliding mode control is applied. Conventional switching control law at a sliding surface is replaced by a smooth control interpolation in a selected boundary layer to avoid the excitation of high-frequency dynamics. Simulation results are presented in comparison with those obtained by applying adaptive control.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2001년도 춘계학술대회 논문집(한국공작기계학회)
• /
• pp.188-191
• /
• 2001

Generally, main factors of tool damage are cutting speed, feed rate and depth of cut. The increase of those factors can cause tool breakage or worsen product quality such as machining accuracy deterioration. Those three factors are concerned with cutting force. Cutting force reaches at its maximum value when cutter blade cuts away the object directly, and it is the time when tool damages are at high probability. In this study, we detect the maximum cutting force affecting tool damage and control the maximum cutting force based on the measured peak force.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 추계학술대회 논문집
• /
• pp.690-694
• /
• 1996

In order to regulate the cutting force at a desired level during peripheral end milling processes, a feedrate override Adaptive Control Constant system was developed. This paper presents an explicit pole-assignment PI-control law through spindle motor current monitoring and its application to cutting force regulation for feedrate optimization. An experimental set-up is constructed for the commercial CNC machining center without any major changes of the structure. A data transfer system is constructed with standard interface between an IBM compatible PC and a CNC of the machining center. Experimental results show the validity of the system.

• 대한기계학회논문집
• /
• 제16권3호
• /
• pp.468-484
• /
• 1992

본 연구에서는 기존의 유연 볼 엔드밀의 절삭력 모델을 바탕으로 자유 곡면의 정삭 가공에서 발생할 수 있는 과대 또는 과소 절삭을 방지하면서 그 가공의 효율성을 높이기 위한 볼 엔드밀의 이송 속도 결정법을 제시하고자 한다. 먼저, 자유 곡면의 가공에서 발생될 수 있는 공구의 처짐에 따른 가공오차에 대하여 볼 엔드밀 공구의 처 짐벡터와 공작물의 공구 접촉점에서의 법선벡터로 표현되는 가공오차(machining error ) 예측 모델식을 유도하였다. 본 가공오차 예측 모델식은 다시 절삭날당 가지는 이 송량의 함수로 전개되어 그 곡면의 주어진 가공 공차(machining tolerance)를 만족시 키는 이송속도를 결정하게 된다.

• 한국정밀공학회지
• /
• 제13권2호
• /
• pp.133-145
• /
• 1996

This paper presents an indirect cutting force measuring system, which uses the current signals from the AC servo drive units of the horizontal machining center, with its applications to the adaptive regulation of the cutting forces in various milling processes and to the on-line monitoring of tool breakage. A typical model for the feed-drive control system of a horizontal machining center is developed to analyze cutting force measurement from the drive motor. The pulsating milling forces can be measured indirectly within the bandwidth of the current feedback control loop of the feed-drive system. It is shown that the indirectly measured cutting force signals can be used in the adaptive controller for cutting force regulation. The whole scheme has been embedded in the commercial machining center and a series of cutting experiments on the face cutting processes are performed. The adaptive controller reveals reliable cutting force regulating capability against the various cutting conditions. It is also shown that the tool breakage in milling can be detected within one spindle revolution by adaptively filtering the current signals. The effect of the cutter run-out has been considered for the reliable on-line detection of tool breakage.

• 한국정밀공학회지
• /
• 제12권2호
• /
• pp.123-134
• /
• 1995

In this paper, the fast force algorithm has been studied so that it is used to calculate cutting forces and to develope the NC verification system. The NC verification using the fast force algorithm can verify excessive cutting force which is the cause of deflection and breakage of tool, and adjust the feed rate and spindle speed.

• 대한기계학회논문집A
• /
• 제26권9호
• /
• pp.1888-1896
• /
• 2002

This study presents a new type of CNC interpolator that is capable of generating cutter paths for ball-end milling of NURBS surfaces. The proposed surface interpolator comprises real-time algorithms for cutter contact (CC) path scheduling and CC path interpolator. Especially in this study, a new interpolator module to regulate cutting forces is developed. This propose algorithm utilizes variable-feedrate commands along the CC path according to the curvature of machined surfaces during the interpolation process. Additionally, it proposes an OpenGL graphic library for computer graphics and animation of interpolated tool-position display. The proposed interpolator is evaluated and compared with the existing method based on constant feedrates through computer simulations.

• 대한기계학회논문집
• /
• 제19권7호
• /
• pp.1555-1562
• /
• 1995

This study represents the non-dimensional cutting force model. With the non-dimensional cutting force model it is possible to estimate efficiently the maximum cutting force during one revolution of cutter. Using the non-dimensional cutting force model, the feed rate and spindle speed are adjusted so as to satisfy the maximum cutting force and maximum machining error. To verify the accuracy and efficiency of the non-dimensional cutting force model, a series of experiments were conducted, and experimental results proved and verified the non-dimensional cutting force model. The NC toolpath verification system developed in this paper uses the non-dimensional cutting force model, so that it is effective for calculating the cutting force and adjusting the cutting conditions.