• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.2
• /
• pp.133-145
• /
• 1996

This paper presents an indirect cutting force measuring system, which uses the current signals from the AC servo drive units of the horizontal machining center, with its applications to the adaptive regulation of the cutting forces in various milling processes and to the on-line monitoring of tool breakage. A typical model for the feed-drive control system of a horizontal machining center is developed to analyze cutting force measurement from the drive motor. The pulsating milling forces can be measured indirectly within the bandwidth of the current feedback control loop of the feed-drive system. It is shown that the indirectly measured cutting force signals can be used in the adaptive controller for cutting force regulation. The whole scheme has been embedded in the commercial machining center and a series of cutting experiments on the face cutting processes are performed. The adaptive controller reveals reliable cutting force regulating capability against the various cutting conditions. It is also shown that the tool breakage in milling can be detected within one spindle revolution by adaptively filtering the current signals. The effect of the cutter run-out has been considered for the reliable on-line detection of tool breakage.

• Clean Technology
• /
• v.18 no.1
• /
• pp.43-50
• /
• 2012

Cleaning procedure of solar silicon wafer, following ingot sawing process in solar cell production is studied. Types of solar silicon wafer can be divided into monocrystalline or multicrystalline, and slurry sawn wafer or diamond sawn wafer according to the ingot growing methods and the sawing methods, respectively. Wafer surface and contaminants can vary with these methods. The characterisitics of contaminants and wafer surface are investigated for each cleaning substrate, and appropriate cleaning agents are developed. Physical properties and cleaning ability of the cleaning agents are evaluated in order to verify the application in the industry. The wafers cleaned with the cleaning agents do not show any residual contaminants when analyzed by XPS and regular patterns are formed after texturization. Furthermore, the cleaning agents are applied in the production industry, which shows superior cleaning results compared to the existing cleaning agents.

• Proceedings of the Korean Operations and Management Science Society Conference
• /
• 1995.04a
• /
• pp.71-71
• /
• 1995

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.17 no.2
• /
• pp.141-151
• /
• 2015

A new rock excavation method using an abrasive injection waterjet system has been developed to enhance the efficiency and reduce the vibration of tunnel excavation. The abrasive feed rate is an important factor for the cutting performance and the economical efficiency of waterjet-based excavation. In this study, various experiments were performed to explore the effects of major process parameters for both the abrasive feed rate and the suction pressure occurring inside the mixing chamber when the abrasives are inhaled. Experimental results reveal that the abrasive feed rate is affected by geometry parameters (abrasive pipe height, length, and tortuosity), abrasive parameters (abrasive particle size), and jet energy parameters (water pressure and water flow rate). In addition, the relation between the cutting performance and the abrasive feed rate was discussed on the basis of the results of an experimental study. The cutting performance can be maximized when the abrasive feed rate is controlled appropriately via careful management of major process parameters.

• Korean Journal of Materials Research
• /
• v.8 no.7
• /
• pp.641-647
• /
• 1998

The machinability properties of P/M 2011 AI alloys extruded rapidly solidified by rotating disc atomization were investigated in this study. The Pb-Bi particles were very uniformly and finely dispersed in the P/M 2011 AI alloys extruded rapidly solidified. According to the increase of cutting speed, the short discontinuous chips were produceed and continuous chips were formed from the lower feed values of O.lmm/rev. The surface roughness is depend on the feed values, not cutting depth and cutting speed. The short discontinuous chips were formed due to dispersed $AI_20_3$ particles and Pb- Bi inclusion.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.4 no.2
• /
• pp.46-53
• /
• 2000

Hot forging of aluminum alloy has the bad machinability due to continuous chip formation caused from the ductility The bad machinability requires a labor and a high cost to produce final products after hot forging. In industrial field, T4 heat treatment is performed to improve the machinability, and the annealing and the cold sizing are followed. In this study, a series of heat treatments are introduced during hot forging operation without T4 heat treatment after forming so that it improves the machinability with reduction of the number of operations and machining cost. Instead of T4 heat treatment, water cooling and air cooling are tried and compared to find out an optimum cooling condition

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.17 no.31
• /
• pp.91-98
• /
• 1994

Most of machines are physically or chemically degenerated by continuous usage. There- fore, a preventive maintenance is necessary. Producing defects are caused by process shift in mean and variance which are due to three types of degeneration. We develope the function of process variance from the experimental data and determine the optimal tool wear limit and the initial setting position of tool by considering the percent defective cost and the preventive maintenance cost.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.11a
• /
• pp.648-652
• /
• 1996

Grinding Center(GC)는 머시닝센터가 갖는 드릴링, 태핑 등의 절삭가공의 수행은 물론 주축의 고속화, 이송계의 고정밀화를 토대로 연삭숫돌의 절삭성 회복과 다듬질면의 거칠기를 확보하기 위한 기계로서 Dressing/Truing장치, 기상계측 장치, CNC기능을 구비하여 테이블과 공구간에 3차원의 상대운동을 시킴으로써 평면연삭, 내면연삭, 홈연삭, 캠연삭 등의 복잡한 형상의 연삭가공에 대해서도 공정을 집약화 할 수 있는 기계이다.(중략)

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.1
• /
• pp.107-114
• /
• 2017

A turbocharger is an engine supercharger that is driven by exhaust gas. It improves the output and fuel efficiency by increasing the charging efficiency of the mixture gas, which is achieved by changing the rotatory power of the turbine connected to the exhaust passage. It is important to control the supercharging for this purpose. A nozzle slide joint is one of the core parts. Austenitic stainless steel is currently used as the material for this part, and its excellent mechanical properties include high heat resistance and corrosion resistance. However, because of its poor machinability, there are many difficulties in producing products with complicated shapes. Machining is used in the production of nozzle slide joints for high dimensional accuracy after metal powder injection molding. As design variables in this study, we investigated the sintering temperature, product stress, deformation rate, radius of curvature of the punch, and angle of the chamfer punch, which are related to the strain and shapes. The goal is to suggest a forming process using Nitronic 60 that does not require machining to manufacture a nozzle slide joint for a turbocharger. Accordingly, we determined the best process environment using finite-element analysis, the signal-noise ratio, and the Taguchi method for experiment design. The relative density and hydrostatic pressure of the final product were in accordance with the results of the finite element analysis. Therefore, we conclude that the Taguchi method can be applied to the design process of metal powder injection molding.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.1054-1058
• /
• 1995

There have been many research works for the indirect cutting force measurement in machining process, which deal with the case of one-axis cutting process. In multi-axis cutting process, the main difficulties to estimate the cutting forces occur when the feed direction is reversed. This paper presents the indirect cutting force measurement method in contour NC milling processes by using current signals of servo motors. An artificial neural network (ANN) system are suggested. An artificial neural network(ANN) system is also implemented with a training set of experimental cutting data to measure cutting force indirectly. The input variables of the ANN system are the motor currents and the feedrates of x and y-axis servo motors, and output variable is the cutting force of each axis. A series of experimental works on the circular interpolated contour milling process with the path of a complete circle has been performed. It is concluded that by comparing the ANN system with a dynamometer measuring cutting force directil, the ANN system has a good performance.