• 오토저널
• /
• 제9권5호
• /
• pp.49-56
• /
• 1987

This paper is a study on the effect of the cutting speed on the tool wear in turning of the glass fiber reinforced plastics. The wear behavior of cutting tool is studied by means of turning, changing the cutting speed and feed in the wide range. Moreover, the theoretical model applicable to the cutting speed of wide range is analysed. The main results obtained are as follows: The relation between the tool wear and the cutting speed is divided into three range in case of the constant cutting distance. 1) At the low cutting speed, the tool wear is independent of the cutting speed, but dependent mainly on the contact length between tool and glass fiber(lst range). 2) At the high cutting speed, the tool wear is independent of the contact length, and dependent on the cutting speed only(2nd range). The tool wear increases in proportion to the cutting speed. 3) At the higher cutting speed than the speed in the 2nd range, the tool wear is independent both of the cutting speed and the contact length(3rd range). 4) In the 3rd range, tool flank wear is constant and is observed that only the wear of cutting edge increases.

• 대한금속재료학회지
• /
• 제48권7호
• /
• pp.651-659
• /
• 2010

When high-speed interrupted cutting is carried out for die and mold steels with high hardness, CBN tools manifested a significantly longer wear life than carbide, ceramic, or cermet tools in an experiment of face milling characteristics. In addition, it was also found that they secured a stable surface roughness within a range of 1.6 S~6.3 S, an acceptable range for precision machining for polished machining parts. And it makes them acceptable in the precision machining field, except in industries where very high machining accuracy is required. In the high hardness interrupted cutting, it was advantageous to perform a negaland treatment and a honning treatment on the tools' cutting edge to extend tool life and surface roughness. Also, severe crater development was found on the sloped face in CBN tools following high-speed machining. This caused the cutting edge to be weakened and damaged, and ultimately resulted in a shorter tool life. Finally, as a result of EDX mapping inspection, Cr component was detected evenly on the entire crater wear area, which can be included only in STD 11.

• 한국기계가공학회지
• /
• 제18권11호
• /
• pp.76-82
• /
• 2019

This study aims to find the shapes of an end-mill with low cutting temperature during the end-mill process of Ti-6Al-4V alloy. Such ${\alpha}-{\beta}$ titanium alloys are increasingly more used for their high tensile strength and high corrosion resistance. The cutting characteristics of Ti-6Al-4V alloy were studied using an analytical method validated by comparing the estimated cutting resistance with that from experiments. The end-mill shape was analyzed using an experimental method. The end-mill shape with low cutting resistance and low cutting temperature was confirmed by analyzing the signal-to-noise ratios for various conditions. Then, the factors with significance factor of 95% or more were determined in the variance analysis. Finally, an end-mill shape that can ensure a low cutting temperature was proposed.

• 한국기계가공학회지
• /
• 제20권4호
• /
• pp.87-93
• /
• 2021

The mold industry is competitive, and mold should be processed under optimal conditions for efficient processing. However, the cutting conditions of the ball-end mill, which are a major factor in mold processing, are mostly set empirically, and considerable research is required for increasing the tool life and processing accuracy. In this study, a tool dynamometer and an eddy current sensor were used along with NI-DAQ, a data acquisition device, to obtain characteristic values of the cutting force and tool deformation during the ball end-mill machining of inclined surfaces at a machining center. The cutting force and tool deformation were measured in an experiment. It was found that the tool received the greatest cutting force at the end of the machining process, and the deformation of the tool increased rapidly. Furthermore, the cutting force tended to increase with the angle and number of rotations. The deformation increased rapidly during the machining of a 45° inclined surface.

• 소성∙가공
• /
• 제28권4호
• /
• pp.183-189
• /
• 2019

Cylindrical worm reducers are generally used in various fields and forms throughout the industry, and demand is increasing due to their role as an integral part of the industry. Market trends require high-load, high-precision components, and small-sized reducers with large loads. When using a cylindrical worm reducer, a reducer designed with a reduced center distance while maintaining the same output torque results in gear wear. To overcome this difficulty, an enveloping worm gear reducer is introduced and studied. In this paper, three types of end mill tools are used to evaluate the tooth profile accuracy for each tool shape during machining of the tooth profile for a non-developed surface worm thread. The effect of the endmill shape on the accuracy of the tooth profile was analyzed by performing 3D modeling of the surrounding worm tooth profile based on the Hindley method. In this study, we analyzed tooth profile accuracy, tooth surface roughness, and tooth surface machining time, etc. Through the study, efficient machining conditions for the enveloping worm gears and the influence of parameters on the process were presented.

• 한국기계가공학회지
• /
• 제21권6호
• /
• pp.81-88
• /
• 2022

Titanium alloy (Ti-6Al-4V) has excellent mechanical properties and high specific strength; therefore, it is widely used in aerospace, automobile, defense, engine parts, and bio fields. Particularly in the aerospace field, as it has a low specific gravity and rigidity, it is used for the purpose of increasing energy efficiency through weight reduction of parts, and most have a thin-walled structure. However, it is extremely difficult to machine thin-walled shapes owing to vibration and deformation. In the case of thin-walled structures, the cutting forces and vibrations rapidly increase depending on the cutting conditions, significantly affecting the surface integrity and tool life. In this study, machining experiments on thin-wall milling of a titanium alloy (Ti-6Al-4V) were conducted for each experimental condition with different axial depths of cut, radial depth of cut, and machining sequence. The machining characteristics were analyzed, and an effective machining method was derived by a comprehensive analysis of the machined surface conditions and cutting signals.

• 한국정밀공학회지
• /
• 제11권2호
• /
• pp.50-64
• /
• 1994

Cutter deflections in the ball-end milling process is one of the main causes of the machining errors on a free-form surface. In order to avoid machining errors in this process, a methodology avoiding these machining errors on the free-form surfaces has been developed. In this method, feedrates in the finish cuts are adjusted for the prevention of machining errors. A model for the prediction of machining errors on the free-form surface is analytically derived as a function of feed and normal vector at the surface of contact point by the cutter. This model is applied to the dertermination of the adjusted feedrates which satisfy the machining tolerance of the surface. In the finish cuts of a simple curved surface, the suggested model is examined by the measurements of the generated machining error on this surface. And also, this surface is machined with the adjusted feedrates for the given machining tolerance. The measured machining errors on this surface are compared with the given tolerance. In this comparisons, it is shown that the predicted errors are fairly good agreement with the test results.

• 자원리싸이클링
• /
• 제31권4호
• /
• pp.19-25
• /
• 2022

본 연구에서는 텅스텐산암모늄(APT, Ammonium Paratungstate, (NH₄)₁₀[W₁₂O₄₆H₁₀])이 사용되지 않는 친환경 초경합금 슬러지 재활용 공정을 통해 초경합금 주원료인 텅스텐 탄화물 분말을 합성하고자 하였다. 초경합금 슬러지에 대한 산 처리를 통해 텅스텐산(H₂WO₄) 추출 및 결정화를 수행하고 결정화된 텅스텐산을 텅스텐 탄화물의 원료로 사용하였다. H₂WO₄에 대한 탄화환원을 통해 텅스텐탄화물 (WC) 분말이 합성되었고 합성된 WC 분말은 200~700nm 수준의 결정립으로 구성되어 있음이 확인되었다. 이는 현재 절삭공구로 가장 널리 사용되는 1~3㎛ 입도의 상용 WC 분말에 비해 미세한 것으로 텅스텐 금속 분말에 대한 고온(1,700℃ 이상) 고상 탄화법을 통해 제조되는 상용 WC 분말과 달리 H₂WO₄ 나노 결정립에 대한 탄화환원을 통해 WC 분말이 합성되었기 때문으로 사료된다. H₂WO₄로 부터 합성된 WC 분말의 경우 탄화환원에 의해 탄소의 제거가 수월하여 상용 WC 분말에 비해 잔류 탄소가 적은 것으로 확인되었으며 작은 결정립 크기로 인해 초경합금 원료로 사용되었을 때 WC-Co 복합체 내 WC 입자의 성장이 활발하게 일어나 H₂WO₄로부터 합성된 WC 분말이 적용된 WC-Co 복합체의 경우 WC 입자가 조대하고 파괴인성이 우수한 것으로 확인되었다.

• 오토저널
• /
• 제14권6호
• /
• pp.113-126
• /
• 1992

Recently the multi-kind, small-amount manufacturing system has been replacing the mass manufacturing system, and domestic machining inustry also is eager to absorb the new technology because of its high productivity and cost reduction. The optimization of the cutting condition has been a vital problem in the machining industry, which would help increase the productivity and raise the international competitiveness. It is intended in this study to investigate the machining costs per unit time which is essential to the analysis of the optimal cutting condition, to computer the cutting speed that lead to the minimum machining costs and the maximum production to suggest the cutting speed range that enables efficient speed cutting, and to review the machining economy in relation to cutting depth and feed. Also considered are the optimal cutting speed and prodution rated in rrelation with feed. It is found that the minimum-cost cutting speed increases and the efficient cutting speed range is reduced as machining cost per unit time increases since the cutting speed for maximum production remains almost constant. The machining cost is also lowered and the production rate increases as the feed increases, and the feed should be selected to satisfy the required surface roughness. The machining cost and production rate are hardly affected by the cutting depth if the cutting speed stays below 100m/min, however, they are subject to change at larger cutting depth and the high-efficient speed range also is restricted. It can be established an adaptive optimal cutting conditions can be established in workshop by the auto-selection progam for optimal operation. It is expected that this method for choosing the optimal cutting conditions might contribute to the improvement of the productivity and reduced the cost. It is highly recommended to prepare the optimal cutting conditionthus obtained for future use in the programing of G-function of CNC machines. If proper programs that automatically select the optimal cutting conditions should be developed, it would be helpful to the works being done in the machine shops and would result in noticeable production raise and cost reduction.

• 한국정밀공학회지
• /
• 제19권5호
• /
• pp.133-138
• /
• 2002

The technique of high speed machining is widely studied in machining fields, because the high efficiency and accuracy in machining can be obtained in high speed machining. Unfortunately the development of tool fur high speed machining in not close behind that of machine tool. In this study, 10 types flat endmill is prepared for obtaining data according to tool shape. Especially, we concentrated in helix angle, number of cutting edge and rake angle. Cutting condition is selected for several experiments and measuring cutting farce, tool life, tool wear and chip shape according to cutting length. 3-axis cutting farces are acquired from the tool dynamometer with high natural frequency, as the conventional tool dynamometer (9257B, Kistler) has cannot measure the state of high frequency force. Particularly, we found out that the axial cutting force waveform has a good relation with tool wear features. And flow is interrupted at the beginning of cutting by the decrease of rake angle. By above results. it is suggested the endmill tool with 45$^{\circ}$helix angle, 6 cutting edge and -15$^{\circ}$rake angle is suitable for high speed machining.