• Proceedings of the KIPE Conference
• /
• 2016.11a
• /
• pp.105-106
• /
• 2016

영구자석형 동기전동기 (Permanent Magnet Synchronous Motor)의 벡터제어와 같이 자극의 위치를 기준으로 제어를 하는 경우 회전자의 위치 정보는 매우 중요하다. 그래서 위치정보를 얻기 위한 센서로 엔코더, 레졸버, 레치형 홀센서를 사용하는데 보통 가격이 싼 BLDC 모터의 경우는 레치형 홀센서를 많이 사용한다. BLDC 모터의 레치형 홀센서 대신 리니어 홀센서를 장착하여 절대위치를 추출하여 벡터제어를 한다.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.8 no.2
• /
• pp.101-113
• /
• 2006

Arching effect occurs around the unsupported excavation surface near to tunnel face when a tunnel is excavated in a stable rock mass. If a weak fracture zone exists in front of tunnel face, a displacement occurs between tunnel face and weak fracture zone due to stress concentration. If three-dimensional absolute coordinates (longitudinal, transverse, vertical direction) is measured at tunnel face by geodetic method, the ground change in front of the tunnel face can be predicted by analysing three-dimensional absolute displacement. The purpose of this study is to verify the analysis method of three-dimensional absolute displacement by comparing the trend of displacement ratio at crown and sidewall of tunnel and the influence line/trend line of crown settlement compared with TSP results in the same section.

• Journal of Information Technology and Architecture
• /
• v.11 no.4
• /
• pp.441-448
• /
• 2014

The application of spatial information has drawn significant attention from a wide range of industries. Railway spatial information facilitates the cooperation among related parties and improves the efficiency of asset management and operations. This study proposes the structure of Railway Object IDentifier(ROID) on railway spatial information. Current facility management and train operation are based on relative positioning system. Despite many advantages, relative positioning system causes serious problems such as the entire reconfiguration of positioning in the case of line change. Another major concern is the interface compatibility between individual facilities with different relative positioning. ROID based on absolute positioning addresses these issues, allowing the information exchange and convergence between independent parties. This study proposes ROID based on OID standard with object IDentifier and service object-oriented reference system. Our ROID employs the absolute positioning and the unique identifier, maintaining the compatibility with existing management system.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.04a
• /
• pp.156-160
• /
• 1997

This paper introdues the development of hydraulic cylinder with magnetic sensor detecting absolute and precise position for automation of excavator. The system which is developed can detect absolute position witha little displacement by using algorithm for recognizing datum points, 1/4 divider algorithm and high precision algorithm improved position precision and robustness to noise etc. The solenoid valve and PWM control using saw-toothed wave are used for absolute position control of cylinder, respectively

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.4
• /
• pp.68-75
• /
• 2003

This paper introduces the development of hydraulic cylinder with magnetic sensors detecting absolute and precise position for automation of excavator. The system which is developed can detect absolute position with a little displacement by using algorithm for recognizing datum points, 114 divider algorithm and high precision algorithm improved position precision. We alse evaluate the developed system under the load disturbance and add band pass filter to the previous's signal process circuit for the protecting magnetic sensors's saturation.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.10
• /
• pp.141-147
• /
• 2003

This paper represents an absolute positioning system using a light navigation path for mobile robot. The absolute positioning system is composed of the projector unit which generates a laser beam using laser diode and mobile robot with the optical detector which has some optical sensors. The projector unit is fixed over the navigating plane of mobile robot to generate the light navigation path, and the optical detector located upper part of mobile robot detects the generated laser beam from the projector. The navigation of mobile robot is controlled by the micro-processor which compares the detected present position from the detector with the previously programmed navigation path. And experimental results show that our sensor system can be used for the absolute positioning system of the mobile robot.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.26 no.5
• /
• pp.529-536
• /
• 2008

Researches about 3-D Positioning system using GPS were carried out many-sided by national organs, laboratories, the worlds of science. And most of researches were development of relative positioning algorithm and its applications. Relative positioning has a merit, which can eliminate error in received signals. But its error increase due to distance of baseline. GPS absolute positioning is a method that decides the position independently by the signals from the GPS satellites which are received by a receiver at a certain position. And it is necessary to correct various kinds of error(clock error, effect of ionosphere and troposphere, multi-path etc.). In this study, results of PPP(Precise Point Positioning) used Bernese GPS software was compared with notified coordinates by the NGII(National Geographic Information Institute) in order to analyze the positional accuracy of permanent GPS sites. And the results were compared with results of AUSPOS - Online GPS Processing Service for comparison with relative positioning.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.9 no.2
• /
• pp.163-170
• /
• 2004

Since 1960s, a container shipping volume has increased dramatically and continuous on a trend of rapid growth, and so the number of containers handled at the port increases. The position measurement of the yard crane is very important for improving the operating efficiency of the port. This paper describes the method to measure the absolute position of yard crane accurately and rapidly, using both the output pulse of an encoder and infrared sensors. The crane position is calculated by counting the output pulse of an incremental encoder, which is mounted on the wheel in the crane. By the way, the wheel slippage on rail may cause some errors in the crane position information obtained from encoder pulse, and the infrared sensor is used to compensate for errors in the crane position information. The performance of proposed method is verified on experimental results with the simulator of yard crane, the size of which is about 1/10 with the real crane.

• 한국HCI학회:학술대회논문집
• /
• 2006.02a
• /
• pp.362-367
• /
• 2006

지능형 주거공간에서 손 지시 명령을 통하여 가전기기를 선택하거나 로봇에게 이동하여야 하는 장소를 알려 주기 위해, 기존의 시스템은 선택되는 대상 기기의 3 차원 절대 위치를 미리 알고 있어야 한다. 또한 카메라 위치가 변동되었을 경우, 카메라의 위치를 절대좌표계 기준으로 새롭게 측정해야 하는 불편함이 있다. 이를 해결하기 위해 본 논문에서는 팬/틸트 모듈을 가진 두 대의 USB 카메라를 임의의 위치에 배치하더라도, 두 번의 손 지시만으로 선택 대상이 되는 기기의 3 차원 위치를 파악하고 이를 동작시키는 방법을 다룬다. 제안하는 방법에서는 두 대의 카메라 간의 상대 좌표계를 형성하기 위해 각 카메라에 표식을 부착한다. 각 카메라에서 다른 카메라의 표식을 관찰하면 카메라 간의 거리 및 각도를 구할 수 있기 때문에, 하나의 카메라를 기준으로 3 차원 절대 좌표계를 자동으로 설정할 수 있다. 또한, 두 대의 카메라로 사용자의 얼굴과 손을 검출하면 얻어진 기준 좌표계에 대해 얼굴과 손의 3 차원 위치를 계산하고, 두 지점을 연결하는 방향 벡터를 구함으로써 사용자가 손으로 지시하는 방향을 찾는다. 따라서, 카메라를 임의의 위치에 두더라도 사용자의 손 지시 동작만으로 대상체의 차원 위치를 파악할 수 있게 된다. 개발된 시스템의 유용성을 검증하기 위해 각 가전기기의 위치를 제안한 방법으로 구하고 실제 위치와의 오차를 분석하였다. 제안한 방법은 두 대의 USB 카메라와 일반 PC 또는 마이크로 프로세서만으로 구현할 수 있기 때문에 비용이 적게 들고 실시간 처리가 가능하며 사용자의 환경에서 편리성을 높이는 등 많은 장점을 가진다.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.47 no.3
• /
• pp.5-12
• /
• 2010

A novel algorithm which computes the orientations and the locations of mobile robots with repeating feature of ceiling textures is proposed. For orientation computation, the relative angle between a strait line on a ceiling image and the center line of the robot is firstly computed. The relative angle is added to the global reference angles of straight lines of the ceiling and a group of robot orientation candidates is composed. The robot orientation is determined from such orientation candidate group by choosing the closest one to the previous robot orientation. Similarly, the location of the robot is determined from the robot location candidate group by choosing the closest one to the previous robot location, where robot location candidate group is composed by adding the relative location of the robot to global locations of neighboring nodes of the previous robot locations. The experiment has been done to test the accuracy of the algorithm in computing locations and orientations.