• Journal of Korean Society of Forest Science
• /
• v.94 no.6
• /
• pp.488-495
• /
• 2005

This study was conducted to understand the influences of forest structure on throughfall, stemflow and interception loss. The study plots included the natural old-growth deciduous, Pinus koraiensis and Abies holophylla forests in Gwangneung and the rehabilitated young mixed forest in Yangju, Gyeonggido. The Pinus koraiensis and Abies hotophylla had been planted in 1976. The rehabilitated young mixed forest had been established to control erosion in 1974. Total and net rainfall were monitored from March, 2003 to October, 2004. Tipping bucket rain gauge recorded total rainfall. Throughfall and stemflow were measured by custom-made tipping bucket and CR10X data logger at each $10m{\times}10m$ plots at intervals of 30 minutes. Interception loss in the Pinus koraiensis plot were most as 37.2% of total rainfall and least as 22.6% in the rehabilitated young mixed forest. Stemflow in the rehabilitated young mixed forest was 10.7% of total rainfall and stemflow in the Pinus koraiensis plot was 2.4%. The average throughfall ratio ranged from 66% to 77% depending on the canopy coverage. The relationship of stemflow and total rainfall represented in a linear regression equation though the variation of data was large. The ratio of stemflow-conversion was 2% of total rainfall in the Pinus koraiensis plot and 12% in the rehabilitated young mixed forest, respectively. The stem storage of the natural old-growth deciduous was the largest of 0.21 mm whereas that of the Pinus koraiensis plot was the least of 0.003 mm. A deciduous forest produced stemflow more than a coniferous forest due to a smooth bark and steeply angled branches. Interception loss of all study plots increased linearly as total rainfall increased. The distribution of interception loss data related in total rainfall became wider in a deciduous forest than a coniferous. It resulted from seasonality of leaf area index in a deciduous forest. As considered above results, it was confirmed that there were great differences of throughfall, stemflow and interception loss depending on forest stand structures. The simulation model for predicting interception loss must have parameters such as forest stand characteristics and LAI in order to describe the influence of forest structure on interception loss.

• Journal of Korean Society of Forest Science
• /
• v.94 no.6
• /
• pp.496-503
• /
• 2005

This study was conducted to investigate the influences of sapflow flux on soil water tensions and soil moisture content at the Abies holophylla plots in Gwangneung, Gyeonggido, from September to October 2004. The Abies holophylla had been planted in 1976 and thinning and pruning were carried out in 1996 and 2004. Sapflow flux was measured by the heat pulse method, and soil water tension was measured by tensiometer at hillslope and streamside. Time domain reflectometry probes (TDR) were positioned horizontally at the depth of 10, 30 and 50 cm to measure soil moisture content. All of data were recorded every 30 minutes with the dataloggers. The sapflow flux responded sensitively to rainfall, so little sapflow was detected in rainy days. The average daily sapflow flux of sample trees was 10.16l, a maximum was 15.09l, and a minimum was 0.0l. The sapflow flux's diurnal changes showed that sapflow flux increased from 9 am and up to 0.74 l/30 min. The highest sapflow flux maintained by 3 pm and decreased almost 0.0 l/30 mm after 7 pm. The average soil water tensions were low ($-141.3cmH_2O$, $-52.9cmH_2O$ and $-134.2cmH_2O$) at hillslope and high ($-6.1cmH_2O$, $-18.0cmH_2O$ and $-3.7cmH_2O$) at streamside. When the soil moisture content decreased after rainfall, the soil water tension at hillslope responded sensitively to the sapflow flux. The soil water tension decreased as the sapflow flux increased during the day time, whereas increased during the night time when the sapflow flux was not detected. On the other hand, there was no significant relationship between soil water tension and sapflow flux at streamside. Soil moisture content at hillslope decreased continuously after rain, and showed a negative correlation to sapflow flux like a soil water tension at hillslope. As considered results above, it was confirmed that the response of soil moisture tension to sapflow flux at hillslope and streamside were different.

• Asia-Pacific Journal of Business Venturing and Entrepreneurship
• /
• v.8 no.3
• /
• pp.189-204
• /
• 2013

Today, politics, economy and technique in the world are rapidly changed. To respond to these changes public institutions as well as government and corporate try to change themselves and to adapt these situation and environment. Total payroll costs system which is one of critical methods to adapt changing world began to introduce in 2004 for public services in Korea. After exhibition and enforcement, all education administration in Korea adopted this system in 2013. This study focus on how total payroll costs system can be successfully controled and utilized, and who this system increase organizational effectiveness and efficacy in public services. Organizational members' effort, perspective, attitude and behavior are most important factors for organizational change and new option. Organizational change and adaptation always involve members' change and adaptation, so this study emphasizes on members' perspective and attitude on total payroll costs system. As a result, distribution justice, procedure justice, and receptivity about total payroll costs system are related to organizational performance such as job satisfaction and organizational commitment. This means organizational members' perspective(distribution justice and procedure justice) and attitude(receptivity) are most crucial factors for effectiveness and efficacy of total payroll costs system. Furthermore with distribution justice, procedure justice and receptivity, total payroll costs system would increase members' job satisfaction and organizational commitment. To sum up, members' perspective and attitude are most important factors for change, thus for success of total payroll costs system, we should understand how people are critical, especially their distribution justice, procedure justice, and receptivity; and also how total payroll costs system are valuable system; and how we can control and handle this system.

• Investigative Magnetic Resonance Imaging
• /
• v.13 no.1
• /
• pp.31-39
• /
• 2009

Purpose : This study proposes the keyhole method in order to improve the time resolution of the proton resonance frequency(PRF) MR temperature monitoring technique. The values of Root Mean Square (RMS) error of measured temperature value and Signal-to-Noise Ratio(SNR) obtained from the keyhole and full phase encoded temperature images were compared. Materials and Methods : The PRF method combined with GRE sequence was used to get MR temperature images using a clinical 1.5T MR scanner. It was conducted on the tissue-mimic 2% agarose gel phantom and swine's hock tissue. A MR compatible coaxial slot antenna driven by microwave power generator at 2.45GHz was used to heat the object in the magnetic bore for 5 minutes followed by a sequential acquisition of MR raw data during 10 minutes of cooling period. The acquired raw data were transferred to PC after then the keyhole images were reconstructed by taking the central part of K-space data with 128, 64, 32 and 16 phase encoding lines while the remaining peripheral parts were taken from the 1st reference raw data. The RMS errors were compared with the 256 full encoded self-reference temperature image while the SNR values were compared with the zero filling images. Results : As phase encoding number at the center part on the keyhole temperature images decreased to 128, 64, 32 and 16, the RMS errors of the measured temperature increased to 0.538, 0.712, 0.768 and 0.845$^{\circ}C$, meanwhile SNR values were maintained as the phase encoding number of keyhole part is reduced. Conclusion : This study shows that the keyhole technique is successfully applied to temperature monitoring procedure to increases the temporal resolution by standardizing the matrix size, thus maintained the SNR values. In future, it is expected to implement the MR real time thermal imaging using keyhole method which is able to reduce the scan time with minimal thermal variations.

• Journal of Radiation Protection and Research
• /
• v.10 no.2
• /
• pp.96-108
• /
• 1985

A study for the assessment of natural environmental radiation exposure at a flat and open field of about $10,000m^2$ in area in CNU Daeduk campus has been carried out by means of gamma-ray scintillation spectrometry and thermoluminescence dosimetry for one year period of time from October 1984. The detectors used were 3'${\phi}{\times}$3' NaI(T1) and two different types of LiF TLD, namely, chip sealed in plastic sheet which tightly pressed on two open holes of a metal plate and Teflon disk. Three 24-hour cycles of in-situ spectrometry, and two 3-month and one 1-month cycles of field TL dosimetry were performed. All the spectra measured were converted into exposure rate by means of G(E) opertaion, and therefrom exposure rate due to terrestrial component of environmental radiation was figured out. Exposure rate determined by the spectrometry was, on average, $(10.54{\pm}2.96){\mu}R/hr$, and the rates of $(12.0{\pm}3.4){\mu}R/hr$ and $(11.0{\pm}3.6){\mu}R/hr$ were obtained from chip and disk TLD, respectively. Fluctuations in diurnal variation of the exposure rate measured by the spectrometry were noticeable sometime even in a single cycle of 24 hours. It is concluded that appropriately combined use of TLD with iu-sitn gamma-ray spectrometry system can give more accurate and precise measure of environmental radiation exposure, and further study for more adequate and sensitive TLD for environmental dosimetry, including improvement and elevation of accuracy in data assessment through inter-laboratory or international intercomparison is necessary.

• Sijohaknonchong
• /
• v.43
• /
• pp.177-206
• /
• 2015

This paper is written in order to research for the contents and expression of HanYongUn's Sijo. HanYongUn is very famous as monk and independent campaigner, modern poet in Korea. He wrote many kinds of literary works, for example, many modern poetry, modern novels, Sijo, Chino-Korean Poetry etc. It's very exceptional that he wrote a lot of Korean traditional Sijo and Chino-Korean Poetry. Because he was a many modern poet as same as modern novelist. So studying on his Sijo can help someone to understand the essence of HanYongUn's all literature. That's why I'm studying on HanYongUn's Sijo. The firstly, in aspect of the the contents of HanYongUn's Sijo, HanYongUn was expressing three kinds of themes, that is ideology, reality, daily life in his Sijo. The ideology consists of Buddhism and Confucianism and the reality is related with social conditions, the daily life is deeply connected with Nim. These features of his Sijo are different from his modern poetry and Chino-Korean Poetry which had a simple theme, for example, love with Nim, daily life. The secondly, in aspect of the expression of HanYongUn's Sijo, I studied the expression of HanYongUn's Sijo in three angles, that is, vocabulary and the developing of poet thinking, rhetorics. HanYongUn used essential words for expressing three kinds of themes effectively in his Sijo. And he was developing of his poet thinking by three steps in his Sijo. He applied several representative rhetorics to his Sijo, those are question and answer, exclamation, irony, distich etc. Even though I studied the characteristics of HanYongUn's Sijo in two aspects But there could be the other things to study about these kinds of theme. I might continue researching the other kinds of theme next time in the near future.

• Restorative Dentistry and Endodontics
• /
• v.31 no.4
• /
• pp.323-329
• /
• 2006

The aim of this study was to evaluate the retrievability of Resilon as a root canal filling material Twenty-seven human single-rooted extracted teeth were instrumented utilizing a crown down technique with Gates-Glidden burs and ProFile system. In group1 (n = 12) canals were obturated with gutta percha and AH-26 plus sealer using a continuous wave technique and backfilled. In group 2 (n = 15) Resilon was used as a filling material. Then teeth were sealed and kept in $37^{\circ}C$ and 100% humidity for 7 days. For retreatment, the samples were re-accessed and filling material was removed using Gates-Glidden burs and ProFiles. Teeth were sectioned longitudinally to compare the general cleanliness and amount of debris $({\times}\;75)$ using SEM. Chi-square test was used $({\alpha}\;=\;0.05)$ to analyze the data. The total time required for removal of filling materials was expressed as mean ${\pm}SD$ (min) and analyzed by the Student t-test $({\alpha}\;=\;0.05)$, Required time for retreatment was $3.25\;{\pm}\;0.32$ minutes for gutta percha/ AH 26 plus sealer and $3.05\;{\pm}\;0.34$ minutes for Resilon. There was no statistically significant difference between the two experimental groups. There was no significant difference between the groups in the cleanliness of the root canal wall. This study showed that Resilon was effectively removed by Gates-Glidden burs and ProFiles.

• Restorative Dentistry and Endodontics
• /
• v.24 no.2
• /
• pp.408-415
• /
• 1999

When a zinc-oxide eugenol type sealer was placed in root canals treated previously with calcium hydroxide, acceleration of its setting and the yellowish discoloration were observed clinically. The purpose of this study was to evaluate the properties of calcium hydroxide-eugenol compound. Some physical properties of calcium hydroxide-eugenol compound were compared with a manufactured zinc-oxide eugenol based root canal sealer, Tubli-seal$^{(R)}$ in terms of water solubility, water sorption, film thickness and microleakage. Solubility and water sorption were determined by the use of the method described in American Dental Association Specification(ADAS) no. 57. Ten samples of each material were prepared into disks 20mm in diameter and 1.5mm in thickness. The samples were immersed in 50ml of distilled water at $37{\pm}1^{\circ}C$ for 7 days. The samples were then removed and placed in a desiccator. The values for solubility and water sorption were calculated using differences between the weights of same sample. Film thickness was determined by the use of the method described in ADAS no. 57 too. A small quantity of mixed cement was placed between two glass plates of which thickness was measured previously. 15Kg loading was applied and total thickness of the glass plates and the cement film was measured. The thickness difference was recorded as the material's film thickness. Microleakage was determined with a dye penetration method. Experimental materials were placed between the dentin surface of bovine tooth and the acrylic rod. These units were immersed in Pelican ink (W-Germany) for three days. Dye-penetrated dentin surfaces of bovine tooth were measured using the NIB Image 1.60 Macintosh program. The results are as follows: 1. Water solubility value of calcium hydroxide-eugenol compound (20.98${\pm}$2.94%) was statistically higher than those of Tubli-seal$^{(R)}$(2.52${\pm}$0.49%)(p<0.05). 2. Water sorption value of calcium hydroxide-eugenol compound (59.72${\pm}$17.75%) was statistically higher than those of Tubli-seal$^{(R)}$(3.15${\pm}$0.76%)(p<0.05). 3. Film thickness value of calcium hydroxide-eugenol compound (0.36${\pm}$0.03mm) was statistically higher than those of Tubli-seal$^{(R)}$(0.12${\pm}$0.1mm)(p<0.05). 4. Dye penetration value after 3 days-immersion of calcium hydroxide-eugenol compound(57.63${\pm}$25.85%) was statistically higher than those of Tubli-seal$^{(R)}$(28.05${\pm}$23.46%)(p<0.05).

• Korean Journal of Environmental Agriculture
• /
• v.16 no.4
• /
• pp.394-398
• /
• 1997

Changes of nutrient material and heavy metals of irrigation water and natural supplies by irrigation water into 1.0ha of paddy field during the rice cultivation was investigated pH of irrigation water ranged 6.458.34 and electrical conductivity showed $110{\mu}S/cm$ in the first irrigation period and commonly showed $90{\mu}S/cm$. The content of T-N, NH4-N and $NO_3-N$were 3.09~12.36, 0.17~1.34 and 2.70~10.72mg/L respectively. The content of T-P was 0.09~0.22mg/L and ortho-P was not detected. The content of $Ca^{++},\;Mg^{++},\;Na^+\;and\;K^+$ showed 0.89~5.12, 1.12~2.76, 1.74~4.52 and 1.34~4.18mg/L regardless of irrigation season respectively. Only Cu and Zn of heavy metals were detected 0.001~0.009 and 0.007~0.091mg/L, but Pb, Cd, Cr and Ni were not detected When supplied $4,250m^3$ of an irrigation water into 1.0㏊ of paddy field, natural supplies of nutrient materials were 29.67㎏ of T-N, 1.80㎏ of $NH_4-N$, 24.57kg of NO3-N and 0.51kg of T-P. Also $Ca^{++},\;Mg^{++},\;Na^+,\;K^+,\;Cl^-\;and\;SO_4\;^{2-}$ were supplied 9.42, 7.09, 13.34, 9.08, 40.27 and 41.38kg respectively. Only Cu and Zn of heavy metals were supplied 0.017kg of Cu and 0.133kg of Zn, Pb, Cd, Cr and Ni were not supplied

• Korean Journal of Environmental Agriculture
• /
• v.16 no.4
• /
• pp.399-403
• /
• 1997

Changes of nutrient material and natural supplies by sediment of irrigation water into 1.0ha of paddy field during the rice cultivation were investigated. TSS of the sediment contained irrigation water ranged 52.9${\sim}$125.6mg/L and content of organic matter showed 1.89${\sim}$2.33%. Content of T-N, $NH_4-N$ and $NO_3-N$ were 623.5${\sim}$1775.2, 22.9${\sim}$75.8 and 10.2${\sim}$72.1mg/kg respectively. Content of T-P and ortho-P were 186.7${\sim}$375.7 and 12.4${\sim}$38.9mg/kg respectively. The content of exchangeable canons, $Ca^{++},\;Mg^{++}\;Na^+\;and\;K^+$ were 435.3${\sim}$737.5, 127.3${\sim}$204.2, 36.6${\sim}$94.9 and 105.6${\sim}$232.9mg/kg respectively. Total content of heavy metals were 13.4 of Pb, 0.6 of Cd, 8.2 of Ni, 12.1 of Cu, 29.8 of Zn and 19.7mg/kg of Cr. During the period of rice cultivation, when supplied 4,250m^3 of an irrigation water into 1.0ha of paddy field, natural supplied 346.01kg of sediment, 7.11kg of organic matter, 0.50kg of T-N, 0.02㎏ of NH_4-N, 0.01kg of NO_3-N, 0.08kg of T-P and 0.01㎏ of Ortho-P. Also exchangeable $Ca^{++},\;Mg^{++}\;Na^+\;and\;K^+$ were supplied 0.21, 0.06, 0.02 and 0.06kg respectively. Loaded of the total heavy metal showed natural background level.