• Journal of the Korean Geotechnical Society
• /
• 제28권5호
• /
• pp.13-25
• /
• 2012

Ground anchor method is one of the most popular reinforcing technology for slope in Korea. For the health monitoring of slope which is reinforced by permanent anchor for a long period, monitoring of the tension force of ground anchor is very important. However, since electromechanical sensors such as strain gauge and V/W type load cell are also subject to long-term risk as well as suffering from noise during long distance transmission and immunity to electromagnetic interference (EMI), optical FBG sensors embedded tendon was developed to measure strain of 7-wire strand by embedding FBG sensor into the center king cable of 7-wire strand. This FBG sensors embedded tendon has been successfully applied to measuring the short-term anchor force. But to adopt this tendon to long-term monitoring, temperature compensation of the FBG sensors embedded tendon should be done. In this paper, we described how to compensate the effect in compliance with the change of underground temperature during long-term tension force monitoring of ground anchors by using optical fiber sensors (FBG: Fiber Bragg Grating). The model test was carried out to determine the temperature sensitivity coefficient (${\beta}^{\prime}$) of FBG sensors embedded tendon. The determined temperature sensitivity coefficient ${\beta}^{\prime}=2.0{\times}10^{-5}/^{\circ}C$ was verified by comparing the ground temperatures predicted from the proposed sensor using ${\beta}^{\prime}$ with ground temperatures measured from ground thermometer. Finally, temperature compensations were carried out based on ${\beta}^{\prime}$ value and ground temperature measurement from KMA for the tension force monitoring results of tension type and compression type anchors, which had been installed more than 1 year before at the test site. Temperature compensated tension forces are compared with those measured from conventional load cell during the same measuring time. Test results show that determined temperature sensitivity coefficient (${\beta}^{\prime}$) of FBG sensors embedded tendon is valid and proposed temperature compensation method is also appropriate from the fact that the temperature compensated tension forces are not dependent on the change of ground temperature and are consistent with the tension forces measured from the conventional load cell.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• 제6권4호
• /
• pp.307-327
• /
• 2008

Geochemical study on the rocks and minerals of the Gyeongju low and intermediate level waste repository was carried out in order to provide geochemical data for the safety assessment and geochemical modeling. Polarized microscopy, X-ray diffraction method, chemical analysis for the major and trace elements, scanning electron microscopy(SEM), and stable isotope analysis were applied. Fracture zones are locally developed with various degrees of alteration in the study area. The study area is mainly composed of granodiorite and diorite and their relation is gradational in the field. However, they could be easily distinguished by their chemical property. The granodiorite showed higher $SiO_2$ content and lower MgO and $Fe_2O_3$ contents than the diorite. Variation trends of the major elements of the granodiorite and diorite were plotted on the same line according to the increase of $SiO_2$ content suggesting that they were differentiated from the same magma. Spatial distribution of the various elements showed that the diorite region had lower $SiO_2,\;Al_2O_3,\;Na_2O\;and\;K_2O$ contents, and higher CaO, $Fe_2O_3$ contents than the granodiorite region. Especially, because the differences in the CaO and $Na_2O$ distribution were most distinct and their trends were reciprocal, the chemical variation of the plagioclase of the granitic rocks was the main parameter of the chemical variation of the host rocks in the study area. Identified fracture-filling minerals from the drill core were montmorillonite, zeolite minerals, chlorite, illite, calcite and pyrite. Especially pyrite and laumontite, which are known as indicating minerals of hydrothermal alteration, were widely distributed in the study area indicating that the study area was affected by mineralization and/or hydrothermal alteration. Sulfur isotope analysis for the pyrite and oxygen-hydrogen stable isotope analysis for the clay minerals indicated that they were originated from the magma. Therefore, it is considered that the fracture-filling minerals from the study area were affected by the hydrothermal solution as well as the simply water-rock interaction.

• Computational Structural Engineering
• /
• 제7권3호
• /
• pp.95-103
• /
• 1994

The safety related components in the nuclear power plant should be designed to withstand the seismic load. Among these components the integrity of reactor internals under earthquake load is important in stand points of safety and economics, because these are classified to Seismic Class I components. So far the modelling methods of reactor internals have been investigated by many authors. In this paper, the dynamic behaviour of reactor internals of Yong Gwang 1&2 nuclear power plants under SSE(Safe Shutdown Earthquake) load is analyzed by using of the simpled Global Beam Model. For this, as a first step, the characteristic analysis of reactor internal components are performed by using of the finite element code ANSYS. And the Global Beam Model for reactor internals which includes beam elements, nonlinear impact springs which have gaps in upper and lower positions, and hydrodynamical couplings which simulate the fluid-filled cylinders of reactor vessel and core barrel structures is established. And for the exciting external force the response spectrum which is applied to reactor support is converted to the time history input. With this excitation and the model the dynamic behaviour of reactor internals is obtained. As the results, the structural integrity of reactor internal components under seismic excitation is verified and the input for the detailed duel assembly series model could be obtained. And the simplicity and effectiveness of Global Beam Model and the economics of the explicit Runge-Kutta-Gills algorithm in impact problem of high frequency interface components are confirmed.

• Journal of Life Science
• /
• 제17권12호
• /
• pp.1660-1668
• /
• 2007

The non-ionic surfactant (NIS) Tween 80 was evaluated for its ability to influence invitro cumulative gas production, dry matter digestibility, cellulolytic enzyme activities, anaerobic microbial growth rates, and adhesion to substrates by mixed rumen microorganisms on rice straw, alfalfa hay, cellulose filter paper and tall fescue hay. The addition of NIS Tween 80 at a level of 0.05% increased significantly (P<0.05) in vitro DM digestibility, cumulative gas production, microbial growth rate and cellulolytic enzyme activity from all of substrates used in this study. In vitro cumulative gas production from the NIS-treated substrates; rice straw, alfalfa hay, filter paper and tall fescue hay was significantly (P<0.05) improved by 274.8, 235.2, 231.1 and 719.5% compared with the control, when substrates were incubated for 48 hr in vitro. The addition of 0.05% NIS Tween 80 to cultures growing on alfalfa hay resulted in a significant increase in CMCase (38.1%), xylanase (121.4%), Avicelase (not changed) and amylase (38.2%) activities after 36 h incubation. These results indicated that the addition of 0.05% Tween 80 could greatly stimulate the release of some kinds of cellulolytic enzymes without decreasing cell growth rate in contrast to trends reported with aerobic microorganism. Our SEM observation showed that NIS Tween. 80 did not influence the microbial adhesion to substrates used in the study. Present data clearly show that improved gas production, DM digestibility and cellulolytic enzyme activity by Tween 80 is not due to increased bacterial adhesion on the substrates.

• Korean Journal of Ecology and Environment
• /
• 제48권2호
• /
• pp.129-138
• /
• 2015

Forest vegetation of Geumsusan (1,016.0 m) and Doraksan (964.4 m) in Woraksan National Park is classified into mountain forest vegetation. Mountain forest vegetation is subdivided into deciduous broad-leaved forest, mountain valley forest, coniferous forest, riparian forest, afforestation and other vegetation. Including 77 communities of mountain forest vegetation and 5 communities of other vegetation, the total of 82 communities were researched; mountain forest vegetation classified by physiognomy classification are 37 communities deciduous broad-leaved forest, 16 communities of mountain valley forest, 8 communities of coniferous forests, 1 community of riparian forest, 15 afforestation and 5 other vegetation. As for the distribution rate for surveyed main communities, Quercus variabilis and Quercus mongolica communities account for 33.031 percent of deciduous broadleaved forest, Cornus controversa community takes up 29.142 percent of mountain valley forest, Pinus densiflora community holds 64.477 percent of mountain coniferous forest holds. In conclusion, minority species consisting of Quercus variabilis, Quercus mongolica, Pinus densiflora, Quercus serrata and Cornus controversa are distributed as dominant species of the uppermost part in a forest vegetation region in Woraksan National Park. In addition, because of vegetation succession and climate factors, numerous colonies formed by the two species are expected to be replaced by Quercus variabilis, Quercus mongolica, Cornus controversa and Fraxinus mandshurica which are climax species in the area.

• Knowledge Management Research
• /
• 제22권3호
• /
• pp.151-172
• /
• 2021

The government's implementation of customer-friendly financial policies, such as lowering commission fees for credit card merchants and lowering the maximum interest rate, put the specialized credit finance companies in a crisis of lowering profitability. In this unfavorable situation, the efficiency study of specialized credit finance companies is meaningful. Accordingly, this study measured the efficiency of 34 specialized credit finance companies through Data Envelopment Analysis (DEA) and meta-frontier analysis. For meta-frontier analysis, specialized credit finance companies were divided into two groups (card companies and non-card companies) by industry or three groups (AA0 and above, AA-, and A+ or below) by credit rating. The results of the analysis will provide general insight into the efficiency of specialized credit finance companies. The results of this study are as follows. First, the average meta-efficiency of card companies was analyzed higher than that of non-card companies. Second, 80% of non-card's decision-making units (DMUs) were inefficient by pure technology rather than by scale. Third, decision-making units (DMUs), which account for 62.5% of the credit card company group and 80% of the 'AA-' credit rating group, are in non-economic areas of scale. Fourth, there was no statistically significant difference in meta-efficiency values (TE and PTE) by industry (card companies, non-card companies) and credit rating (AA0 or higher, AA-, A+ or lower). The contribution of this study will provide strategic initiatives for establishing management strategies to improve inefficiency by measuring the efficiency level of companies under an unfriendly business environment for specialized credit finance companies.

• Korean Journal of Heritage: History & Science
• /
• 제39권
• /
• pp.243-280
• /
• 2006

At the Bujang-ri Site, Seosan, South Chungcheong Province, around 220 archaeological features, including semi-subterranean houses and pits of Bronze Age and semi-subterranean houses, pits, and burials of Baekje period had been identified and investigated. In Particular, mound burials No. 5 of 13 of Baekje mound burials yielding a gilt-bronze cap along with other valuable artifacts drew international scholarly attention. The gilt-bronze cap from the mound burial No. 5 is a significant archaeological data not only in the study of Baekje archaeology but also in the study of international affairs and exchange at that time. At the time of exposure, the gilt-bronze cap was already broken into a number of pieces and seriously damaged by corrosion, and hardening and urethane foam were necessary in the process of collecting its pieces. Ahead of main conservational treatments on cap, X-ray photograph and CT(computerizes tomography) were taken in order to examine interior structure of the cap and to decide appropriate treatments. In the five layers identified in the profile of cap, a textile layer was set between a metal and a layerof bark of paper birch for avoiding direct contact of the metal and the bark of paper birch. Analyses were executed for examining textile layer and a layer of fibroid material. According to microscopic analysis, while the textile layer consisted of the simplest plain fabric with one fold among three kinds of textile structures, the layer of fibroid material was mixed with two or three kinds of fibers. A comparative analysis with standard sample using FT-IR (Fourier Transform Infrared Spectroscopy) announced that both textiles and fabrics were hemp. Analysis of kind of the paper birch resulted in barks of paper birch with 15 fold. A metallographic microscope, SEM, and WDS were used for the analysis of microscopic structures of plated metal pieces. While amalgam plating was treated as a plating method, the thickness of the plated layer, a barometer of plating technique, was ranged from $1.72{\mu}m$ to $8.67{\mu}m$. The degree of purity of gold (Au) used in plating was 98% in average, and less than 1% of silver (Ag) was included.

• Journal of Internet of Things and Convergence
• /
• 제8권3호
• /
• pp.1-10
• /
• 2022

The purpose of this study was to investigate how the characteristics of mobile-based financial platforms have an impact on the intention to use loan service users. In addition, it was attempted to investigate whether usefulness and ease of use had a mediating effect in the relationship between each characteristic of the mobile financial platform on the intention to use the loan service. Data collection was conducted from March 1 to April 30, 2022, and 200 people participated in the study. Analysis methods were frequency analysis, exploratory factor analysis, reliability analysis, correlation analysis, hierarchical multiple regression analysis, and three-step mediation regression analysis. The research results are as follows. First, the influence of user factors, technical factors, and environmental factors of a financial platform on the intention to use a mobile loan service was found to be ubiquity in user factors, reliability in technical factors, and facilitation conditions in environmental factors. Second, in the relationship between convenience and intention to use user factors, usefulness had a completely mediating effect. Third, in the relationship between reliability of technical factors and intention to use, usefulness showed a partial mediating effect. Fourth, in the relationship between the social impact of environmental factors and facilitation conditions and intention to use, the usefulness showed a partial mediating effect. Fifth, ease of use showed a completely mediating effect in the relationship between convenience and intention of use of user factors. Sixth, in the relationship between reliability of technical factors and intention to use, ease of use showed a partial mediating effect. Seventh, in the relationship between the social impact of environmental factors and intention to use, ease of use showed a partial mediating effect, and in the relationship between facilitation conditions and intention to use, ease of use showed a fully mediating effect. Through this study, we tried to present basic data on the determinants of the user's acceptable intention to use the mobile loan service.

• Asia Marketing Journal
• /
• 제10권2호
• /
• pp.1-29
• /
• 2008

The objective of our study is to provide an exploratory model for forecasting sales take-off timing of a product in the context of multi-national markets. We evaluated the usefulness of key predictors such as multiple market information, product attributes, price, and sales for the forecasting of sales take-off timing by applying the suggested model to monthly sales data for PDP and LCD TV provided by a Korean electronics manufacturer. We have found some important results for global companies from the empirical analysis. Firstly, innovation coefficients obtained from sales data of a particular product in other markets can provide the most useful information on sales take-off timing of the product in a target market. However, imitation coefficients obtained from the sales data of a particular product in the target market and other markets are not useful for sales take-off timing of the product in the target market. Secondly, price and product attributes significantly influence on take-off timing. It is noteworthy that the ratio of the price of the target product to the average price of the market is more important than the price ofthe target product itself. Lastly, the cumulative sales of the product are still useful for the prediction of sales take-off timing. Our model outperformed the average model in terms of hit-rate.

• Journal of the Korean Society of Food Science and Nutrition
• /
• 제33권9호
• /
• pp.1529-1536
• /
• 2004

This study was designed to determine total trans fatty acids (tFAs) content of processed foods commonly consumed in the Korean diet and to prepare the database for the estimation of tFAs intake in Koreans. Total fat and tFAs content was determined by Soxhlet extraction method and attenuated total reflection infrared spectroscopy (ATR-IR), respectively. The tFAs positional isomers were analyzed using GC/MS spectrometer. In margarines, the content of tFAs ranged from 8.27% to 28.53%. Shortenings contained higher levels of tFAs (1.98~11.33%) than lards (1.83~1.96%). The content of tFAs in grilled confectioneries was wide (7.37~26.54%). Instant popcorns contained the highest amount of tFAs. Fried chickens had 0.44 to 14.85% of tFAs and french fries had 5.18 to 27.01% of tFAs. In fried snacks (crispy) and chocolates, tFAs were not detected. The amount of tFAs per serving size was the highest in instant popcorn, followed by french fries, fried snack (tortilla), doughnuts, and grilled confectioneries. TFAs isomer of margarines was mostly C18:1${\Delta}$9t. In shortenings and lards, the most abundant positional isomer of tFAs was C18:1${\Delta}$9t and C18:2${\Delta}$9t ${\Delta}$12t. Correlation coefficient of tFAs content between IR and GC/MS method was $r^2$=0.91.