• 한국태양에너지학회 논문집
• /
• 제22권2호
• /
• pp.33-38
• /
• 2002

In order to find out whether solar air conditioning system could be applied to building or not, the performance and evaluation on thermal environment of the system suggested was done during summer. A solar model house was constructed to find out the performance and thermal environment evaluation when it actually operated outside. As a result, regeneration rate increased rapidly when LiCl solution temperature was over $50^{\circ}C$ and the regeneration rate was $13\sim15kg$ during 9 hours operation. Furthermore the dehumidification rate was 12kg at maximum during 10 hours operating of a dehumidifier and indoor temperature and relative humidity was $28.4^{\circ}C$ and 39.1% in average respectively. On evaluation of thermal environment during summer, PMV value was slightly high, but thermal sensation vote was 71% within the comfort zone.

• 설비공학논문집
• /
• 제26권2호
• /
• pp.61-66
• /
• 2014

Exhaust heat recovery ventilation systems conserve energy through enthalpy recovery between air intake and exhaust, and they are being increasingly used. An exhaust heat recovery ventilation system can be installed in the ceiling of a balcony or emergency evacuation space. However, in the case of fire, the emergency evacuation space has to by law remain as empty space, and therefore, a ventilation system can't be installed in an emergency evacuation space. Therefore, the need for a proper installation space for a ventilation system is emphasized. In this study, to install a heat recovery ventilation system in a lightweight wall, a heat exchanger was assembled of thickness below 140 mm. The efficiency of heat recovery was analyzed through performance experiment, in the case of the cooling and heating mode. The heat recovery efficiency increases when the surface area is increased, by using closer channel spacing in the heat exchanger, or by increasing the size of the heat exchanger.

• 태양에너지
• /
• 제19권4호
• /
• pp.55-62
• /
• 1999

This study was performed to find out the influence of experimental factors on dehumidification performance and furthermore to suggest an optimal combination of factors of a total heat exchanger in a solar air conditioning system. The experimental apparatus was set up in a climate-controlled chamber where the temperature and humidity was maintained constant. In order to find out the contribution ratio of factors on dehumidification performance, the table of orthogonal arrays $L_8(2^7)$ was used. According to the results, the most influential factor on dehumidification performance was the concentration of LiCl(Lithium Chloride) solution. The next influential factors were the temperature of LiCl solution and the air flow rate. The packed layer height, packed material, and flow rate of LiCl solution had no influence on the dehumidification performance under these experimental conditions. Through the three level experiments of $L_{27}(3^{13})$, it was found that the optimal combination was $A_2B_0G_2$(concentration of solution 30 wt%, temperature of solution $15^{\circ}C$, air flow rate $253m^3/h$).

• 한국산학기술학회논문지
• /
• 제15권7호
• /
• pp.4052-4056
• /
• 2014

현재 가정용 콘덴싱 가스보일러의 사용을 의무화 하고 있는 추세이며, CO나 NOx와 같은 오염 물질의 배출이 적은 친환경 보일러 사용을 적극 추천하고 있다. 따라서 본 논문에서는 효율을 증가시키기 위하여 가정용 콘덴싱 가스보일러에 사용되는 2차열교환기인 잠열교환기의 튜브(관) 내부에 이너 그루브 형상을 추가 하여 열유동에 대한 해석을 실시하였다. 이너 그루브 형상이 추가됨에 따라서 전열면적은 약 20% 증가하였으며, 이에 따라 열전달량이 증가하는 것을 알 수 있었고, 이를 3차원 수치해석을 이용하여 확인하였다. 또한 이너 그루브 형상을 추가했을 경우 이너 그루브 형상이 없는 잠열교환기 보다 출구 온도가 약 $1^{\circ}C$ 증가하였고, 이는 가정용 콘덴싱 가스보일러의 효율증가에 상당한 도움이 될 것으로 판단된다.

• 항공우주시스템공학회지
• /
• 제14권3호
• /
• pp.1-9
• /
• 2020

본 논문에서는 델타 윙렛 와류 발생기와 후퇴익형 와류 발생기 그리고 가이드 베인이 핀-튜브 유동에서의 압력 손실과 전열 성능에 미치는 효과를 비교하는 연구를 진행하였다. 와류 발생기와 가이드 베인은 채널 높이와 튜브의 지름을 기준으로 무차원화하였고, 위치는 저자들의 연구 결과에 따라 각각의 형상이 우수한 지점을 선정하였다. 레이놀즈 수는 입구 속도와 튜브 지름을 기준으로 하여 1400~8000으로 선정하였다. 결과적으로 압력 손실은 레이놀즈 수 8000에서 가이드 베인이 기존 핀-튜브 대비 4.7% 감소하는 효과를 보였고, 전열 성능은 레이놀즈 수 3800에서 델타 윙렛 와류 발생기가 기존 핀-튜브 대비 33% 정도 증가하는 결과를 확인하였다.

• 설비공학논문집
• /
• 제16권3호
• /
• pp.280-286
• /
• 2004

An experimental study is peformed to examine the heat transfer performance of individual rows of fin-tube heat exchangers. The heat transfer performance is measured using an air-enthalpy type calorimeter. The examined heat exchangers consist of 7mm tube and fin patterns of them are slit and louver types. Equivalent fin spacings are 18 fins per inch(fpi) for all samples, and the number of tube rows are two. In order to confirm that thermal boundary condition on fins of each row are the same, physically separated between two rows as well as connected heat exchangers are used. The frontal air velocity is varied from 0.7 to 2.5㎧. Heat transfer performance for each row is measured. It is observed that the heat transfer coefficient of the second row is smaller than that of the first row at low Reynolds number while larger at high Reynolds number.

• 청정기술
• /
• 제13권4호
• /
• pp.281-286
• /
• 2007

본 연구에서는 폐열회수형 환기장치(전열교환기)로부터의 휘발성 유기화합물이 측정되었다. KS 냉방 및 난방표준조건하에서 휘발성유기화합물의 초기 배출특성을 연구하기 위하여 폐열회수 환기장치로부터 2종류의 열교환소자(L형과 M형)가 평가되었다. 휘발성 유기화합물은 다양한 풍량 변화와 운전시간 변화에 대하여 측정되었다. 본 연구의 분석방법 및 기기상의 한계로 인하여 농도가 비교적 큰 물질만을 살펴보니 페열회수 환기장치에서는 acetic acid, 2-butanone (MEK), 2-(methylthio)ethylamine, toluene, styrene 및 x-acids (Ion 57) 등의 6종의 휘발성 유기화합물이 배출됨을 확인하였다. 배출된 휘발성 유기화합물의 농도는 운전조건에 대해서는 크게 영향을 받지 않았다. 높은 작동온도 때문에 휘발성 유기화합물의 농도는 난방조건보다는 냉방조건에서 더 크게 나타났다.

• 한국정밀공학회지
• /
• 제33권3호
• /
• pp.199-205
• /
• 2016

A thin sheet of metal with corrugated structures has been utilized in various devices: heat exchangers, separators in fuel cells, and many others. However, it is not easy to fabricate thin corrugated structures using a single-step stamping process due to their geometrical complexity. To solve this problem, firstly, a plate type heat exchanger was redesigned to attain the optimal value of aspect ratio and the optimal shape of corrugated structures for the actual loading conditions. A forming analysis of the corrugated plate was then carried out to determine the process parameters. From this work, the optimal value of aspect ratio was found to be 4.6. In addition, the process parameters of heat exchanger forming were optimized using the optimal value of aspect ratio, and the analytical results were evaluated through experiments. The results obtained indicated good agreements between them.

• 설비공학논문집
• /
• 제22권3호
• /
• pp.149-155
• /
• 2010

In the present study, the characteristics on the internal flow and heat transfer of the dimple-type plate heat exchanger were numerically investigated. For the numerical analysis, the conjugate heat transfer analysis between hot fluid-separating plate-cold fluid was performed using the periodic boundary condition at the center area of the plate and appropriate inlet and outlet conditions for the two streams. The numerical results were validated by the comparison with the experimental data. From these results, the correlations of the Colburn j-factor for the heat transfer and the Fanning f-factor for the flow friction were obtained. The present results could be applicable for the optimal design of dimple-type plate heat exchanger.