• Journal of the Korean Institute of Telematics and Electronics T
• /
• v.35T no.1
• /
• pp.48-58
• /
• 1998

For the purpose of designing novel capacitance pressure sensor, several effects on sensitivity such as parasitic capacitance effects, temperature/thermal drift and leakage current have to be eleiminated. This paper proposed the experimental studies on frequency compensation method by electronic circuit technique, C-V converting method with switched capacitor and C-F converting method with schmitt trigger circuit. The third interface circuit by frequency compensation method is composed to eliminate the drift and leakage component by comparision sensing frequency with reference frequency. The signal transmission is realized by digital signal to minimize the influence of noise and high resolution is obtained by means of increasing the number of digital bits. In the fabricated high performance C-V interface, the offset voltage was not appeared, and in case of voltage source, 4.0V, feed back capacitance, 10㎊, the pressure, 0~10 ㎪, the sensitivity of C-V converter is 28 ㎷/㎪.V, the temperature drift characteristic, 0.051 %F.S./$^{\circ}C$ and C-F converter shows -6.6 Hz/pa, 0.078 %F.S./$^{\circ}C$ respectively, relatively good ones.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2002.05a
• /
• pp.271-274
• /
• 2002

In this study, we fabricated the semiconductor laser for optical sensor with 1.55${\mu}{\textrm}{m}$wavelength region. In order to suppress lasing oscillation and to reduce the reflectivity, the devices of bending type were designed and fabricated. Their output power were 1.6㎽ at a pulse drive current of 100㎃. When the fabricated device was applied to optical fiber gyroscope, the output power of optical fiber was 540㎻ at a CW drive current of 100㎃, the full width at half maximum spectral width was 53nm. And the random-walk coefficient was measured to be 2.5$\times$10­$^3$deg/√hr, the gyro output drift was also found to be 0.3 deg/hr. So we confirmed the possibility of application to use for light source of optical fiber gyroscope.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.350-350
• /
• 2008

최근 이동 통신 분야에서 전자기기들의 고주파화와 소형화에 대한 관심이 높아지면서 고주파 소자로서 필수적으로 사용 되어온 디커플링 캐패시터도 이 두 가지 요구를 만족시키기 위해 기존의 표면 실장형에서 평판 형태인 기판 내장형 캐패시터로 발전해 가고 있다. 이를 실현하기 위한 공정법으로 Low Temperature Co-fired Ceramics (LTCCs)와 polymer composite등의 연구가 진행되고 있으나 LTCCs는 높은 공정온도에 의한 내부 확산과 서로 다른 열팽창 계수에 의한 소결후의 수축과 같은 단점들을 가지고 있으며 polymer composite 은 비교적 낮은 공정온도에도 불구하고 유전특성과 방열특성이 우수하지 못한 문제점을 가지고 있었다. 이러한 단점들을 극복하기 위해 Aerosol Deposition Method (ADM)를 주목하게 되었다. 이 공정 법은 상온 저 진공 분위기에서 세라믹 분말을 기판에 고속 분사시켜 기공과 균열이 거의 없는 치밀한 나노구조의 세라믹을 제작하는 새로운 코팅기술이다. 본 연구에서는 고주파용 디커플링 캐패시터의 응용을 위하여 상온에서 높은 유전율을 가지며 강유전체 물질인 $BaTiO_3$를 사용하였다. 출발원료로서 0.45 ${\mu}m$크기의 $BaTiO_3$ 분말을 이용하여 상온에서 submicron에서 수 micron의 두께로 성막하였다. 그러나 ADM으로 $BaTiO_3$ 막을 성막할 경우 유전율이 100이하로 급격히 떨어지는 현상이 기존 연구에서 보고되어 왔으며 본 연구에서도 이를 확인하였다. 디커플링 캐패시터의 밀도를 높이기 위해서 유전체의 유전율을 높이거나 두께를 앓게 하는 방법이 있으나 이번 연구에서는 박막화에 초점을 맞추어 진행하였다. 하지만 $BaTiO_3$ 막의 두께를 $1{\mu}m$이하의 박막으로 제조했을 경우 XRD 분석을 통하여 결정상이 얻어졌음을 확인했음에도 불구하고 유전체로서의 특성을 보이지 않았다. 이 원인을 $BaTiO_3$ 박막의 누설전류에 의한 것이라고 판단하고 $BaTiO_3$ 박막과 기판과의 계면 및 미세구조를 확인하였으며 이것이 전기적 특성에 미치는 영향에 대해 분석하였다.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.11
• /
• pp.1749-1755
• /
• 2010

The performance of power window system was decided by driving characteristics of the window regulator part and reaction by the glass run. The performance of power window system usually has been predicted by experimental methods. In this paper, an analytical method using the explicit code was suggested to overcome the limit of the experimental methods. The friction coefficient of glass run was obtained by the friction test at various conditions and the Mooney-Rivlin model was used. Also, a mechanism of window regulator consisted of the fast belt system and the slip ring elements. And, we conducted the analysis considering characteristic of a motor and obtained the lifting speed of automotive glass with high reliability

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.21 no.2
• /
• pp.71-82
• /
• 1984

A programme, called BIPOLE, for the numerical analysis of twotimensional n-p-n bipolar transistors was developed. It has included the SRH and Auger recolnbination processes, the mobility dependence on the impurity density and the electric field, and the band-gap narrowing effect. The finite difference equations of the fundamental semiconductor equations are formulated using Newton's method for Poisson's equation and the divergence theorem for the hole and electron continuity equations without physical restrictions. The matrix of the linearized equations is sparse, symmetric M-matrix. For the solution of the linearized equations ICCG method and Gummel's algorithm have been employed. The programme BIPOLE has been applied to various kinds of the steady-state problems of n-p-n transistors. For the examples of applications the variations of common emitter current gain, emitter and diffusion capacitances, and input and output characteristics are calculated. Three-dimensional representations of some D.C. physical quantities such as potential and charge carrier distributions were displayed. This programme will be used for the nome,rical analysis of the distortion phenom ana of two-dimensional n-p-n transistors. The BIPOLE programme is available for everyone.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.6 s.121
• /
• pp.656-663
• /
• 2007

In this paper, when a E-polarized plane wave is incident on the grating consisting of tapered resistive strips, electromagnetic scattering is analyzed using the method of moments(MoM). The induced current density of each resistive strip in a grounded double dielectric layer is expected to blow up at both edges. To satisfy this, the induced surface current density is expanded in a series of Chebyshev polynomials of the second kind. The scattered electromagnetic fields are expanded in a series of Floquet mode functions. The boundary conditions are applied to obtain the unknown current coefficients. According to the variation of the involving parameters such as strip width and spacing and angle of the incident field, numerical simulations are performed by applying the Fourier-Galerkin moment method. The numerical results of the normalized reflected power for resistive strips case for several resistivities are obtained.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.14 no.5
• /
• pp.372-378
• /
• 2009

With the increase in capacity of photovoltaic generation systems, studies are being actively conducted to improve system efficiency. In order to develop the high performance photovoltaic power system it is required to understand the physical characteristics of the solar cell. However, solar cell models have a non-linear form with many parameters entangled and conventional methods suggested to extract the parameters of the solar cell model require some kind of assumptions, which accompanies the calculation errors, thereby lowering the accuracy of the model. Therefore, in this paper a novel method is proposed to calculate the ideality factor and reverse saturation current of the solar cell from the I-V curve measured and announced by solar cell manufacturers, derive the ideal I-V curve, and then extract the series and shunt resistances value from the difference between the ideal and measured I-V curve. Also, validity of the proposed method is demonstrated by calculating the correlation between I-V curve based on modeling parameters and I-V curve actually measured through least squares method.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.6
• /
• pp.4158-4163
• /
• 2015

In this paper, the solutions of TE(transverse electric) scattering problems by a condutive strip grating over a dielectric layer are analyzed by using the FGMM(fourier galerkin moment method) and PMM(point matching method) known as a numerical method of electromagnetic fileld. The scattered electromagnetic fields are expanded in a series of floguet mode functions, the boundary conditions are applied to obtain the unknown field coefficients, and the conductive boundary condition is used for the relationship between the tangential electric field and the induced surface current density on the strip. The numerical results for the reflected and transmitted power of zeroth mode analyzed by according as the width and spacing of conductive strip, the relative permittivity and thickness of dielectric layer, and incident angles. Generally, according to the relative permittivity of dielectric layer increased, also the normalized reflected power of zeroth mode increased. To examine the accruacy of this paper, the numerical results of FGMM shown in good agreement compared to those of PMM.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.463-463
• /
• 2010

고휘도 고효율 백색 LED (lighting emitting diode)가 차세대 조명광원으로 급부상하고 있다. 백색 LED를 생산하기 위한 공정에서 MOCVD (유기금속화학증착)장비를 이용한 Epi wafer공정은 에피층과 기판의 격자상수 차이와 열팽창계수차이로 인하여 생성되는 에피결함의 제거를 위하여 기판과 GaN 박막층 사이에 완충작용을 해줄 수 있는 버퍼층 (Buffer layer)을 만들고 그 위에 InGaN/GaN MQW (Multi Quantum Well)공정을 하여 고휘도 고효율 백색 LED를 구현할 수 있다. 이 공정에서 기판의 온도가 불균일해지면 wafer 파장 균일도가 나빠지므로 백색 LED의 yield가 떨어진다. 균일한 기판 온도를 갖기 위한 조건으로 기판과 induction heater의 간격, 가스의 흐름, 기판의 회전, 유도가열코일의 디자인 등이 장비의 설계 요소이다. 코일에 교류전류를 흘려주면 이 코일 안 또는 근처에 있는 도전체에 와전류가 유도되어 가열되는 유도가열 방식은 가열 효율이 높아 경제적이고, 온도에 대한 신속한 응답성으로 인하여 열 손실을 줄일 수 있으며, 출력 온도 제어의 용이성 및 배출 가스 등의 오염 없다는 장점이 있다. 본 연구에서는 유도가열방식의 induction heater를 이용하여 회전에 의한 기판의 온도 균일도 측정을 하였다. 기초 실험으로 저항 가열 히터를 통하여 대류에 의한 온도 균일도를 평가하였다. 그 결과 gap이 3 mm일 때, 평균 온도 $166.5^{\circ}C$ 에서 불균일도 6.5 %를 얻었으며 이를 바탕으로 induction heater와 graphite susceptor의 간격이 3 mm일 때, 회전에 의한 온도 균일도를 측정을 하였다. 가열원은 induction heater (viewtong, VT-180C2)를 사용하였고, 가열된 graphite 표면의 온도를 2차원적으로 평가하기 위하여 적외선 열화상 카메라(Fluke, Ti-10)을 이용하여 온도를 측정하였다. 기판을 회전하면서 표면 온도의 평균과 표준 편차를 측정한 결과 2.5 RPM일 때 평균온도 $163^{\circ}C$ 에서 가장 좋은 5.5 %의 불균일도를 확인할 수 있었고, 이를 상용화 전산 유체 역학 코드인 CFD-ACE+의 모델링 결과와 비교 분석 하였다.

• Applied Chemistry for Engineering
• /
• v.9 no.5
• /
• pp.768-773
• /
• 1998

A mathematical model of discharge mechanism of metal-hydride (MH) electrode was presented. A computer simulation program was developed in order to predict the variation of electrode potential and the distribution of hydrogen concentration within MH particles during discharge. By investigating the effects of the discharge current density, the size of MH particle, the diffusivity of hydrogen in MH particle, and the porosity of the electrode, it was found that these factors exerted a collective effect on the discharge characteristic of the electrode and the utilization of hydrogen in the MH particle. It was confirmed that and optimization of design factors of an MH electrode is necessary in order to execute a high-rate discharge and to improve the utilization of hydrogen in MH particle.