• Journal of the Korean Geotechnical Society
• /
• v.31 no.9
• /
• pp.17-27
• /
• 2015

We perform a series of experimental tests to evaluate whether the shear strength of clean sands can be reliably predicted from shear wave velocity. Isotropic drained triaxial tests on clean sands reconstituted at different relative densities are performed to measure the shear strength and bender elements are used to measure the shear wave velocity. Laboratory tests reveal that a correlation between shear wave velocity, void ratio, and confining pressure can be made. The correlation can be used to determine the void ratio from measured shear wave velocity, from which the shear strength is predicted. We also show that a unique relationship exists between maximum shear modulus and effective axial stress at failure. The accuracy of the equation can be enhanced by including the normalized confining pressure in the equation. Comparisons between measured and predicted effective friction angle demonstrate that the proposed equation can accurately predict the internal friction angle of granular soils, accounting for the effect of the relative density, from shear wave velocity.

• Journal of the Korean Geotechnical Society
• /
• v.31 no.11
• /
• pp.25-31
• /
• 2015

Elastic behavior of the railway roadbed which supports the repeating dynamic loads of the train is mainly affected by the shear modulus of the upper roadbed. Therefore, shear wave velocity estimation of the uniformly compacted roadbed can be used to estimate the elastic behavior of the railway roadbed. The objective of this study is to suggest the relationship between the dynamic cone penetration index (DCPI) and the shear wave velocity ($V_s$) of the upper roadbed in order to estimate the shear wave velocity by using the dynamic cone penetration test (DCPT). To ensure the reliability of the relationship, the dynamic cone penetration test and the measurement of the shear wave velocity are conducted on the constructed upper roadbed. As a method for measurement of the shear wave velocity, cross hole is used and then the dynamic cone penetration test is performed at a center point between the source and the receiver of the cross hole. As a result of the correlation of the dynamic cone penetration index and the shear wave velocity at the same depths, the shear wave velocity is estimated as a form of involution of the dynamic cone penetration index with a determinant coefficient above 0.8. The result of this study can be used to estimate both the shear wave velocity and the strength of the railway roadbed using the dynamic cone penetrometer.

• Journal of the Korean Geotechnical Society
• /
• v.30 no.5
• /
• pp.17-24
• /
• 2014

This paper determines 1D shear wave velocity (Vs) distribution of rockfill zone of CFRD using Vs profile determined by the surface wave test. There exists uncertainty in the field test result because of a spatial variation of material property. The harmonic wavelet transform is used to evaluate the uncertainty of test result and generate random 1D Vs distributions which may exist in the rock fill zone. Through the statistical analysis of generated random Vs distributions, the representative 1D Vs distribution considering the uncertainty of test results is proposed for the rockfill zone of CFRD in Korea.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.23 no.7
• /
• pp.33-39
• /
• 2019

In this study, an experimental study was carried out with variables of the shape of the ground soil-binder in order to find out whether the shear wave velocity and the ground grade were improved by the ground improvement. In this study, the shear wave velocity was measured using the crosshole method with variables of the shape of the ground soil-binder. In addition, the prediction formula of the shear wave velocity for suitability of N-Values for the domestic soil conditions are proposed using the result value of this study and the existing results of shear wave velocity. As a result, the shear wave velocity of the ground has increased. In addition, the prediction formula proposed in this study reasonably issued the existing experimental results regardless of the stratum conditions.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.2
• /
• pp.407-411
• /
• 2009

This study presents the analysis of the identifications and determinations of the material parameters in the developed model in the former paper and their effects on the stress paths. It was shown that the influences of the parameters, specially involved in the strain rate and the viscous nucleus, were in generally acceptable range. From this point, the model was modified by identifying the plastic yield surface and the viscous yield surface in the same mathematical form. The modified model was successful in simulating stress path.

• Journal of the Korean Geotechnical Society
• /
• v.24 no.10
• /
• pp.161-174
• /
• 2008

To investigate the characteristics of the shear wave velocity of cohesive soils and residual soils in Korea, Standard Penetration Test (SPT), Suspension PS Logging tests (SPS) and other soil tests were performed to analyze the shear wave velocity at each layer For these purposes, 2 study sites are selected: one is cohesive soils and the other is residual soils. As a results, new empirical formulas are proposed from the relationship between strength of the ground (N value) and shear wave velocity from the test data at each layer. In the case of cohesive soils, the proposed relationships are nearly similar to empirical formulas, however, in the case of residual soils there was a little difference between the empirical formulas and measured velocities in this study. Case examples for shear wave velocites are presented with depth, N-values and compared with Ohta et al. (1978) empirical formula.

• Journal of the Korean Geotechnical Society
• /
• v.29 no.5
• /
• pp.39-52
• /
• 2013

The shear stress characteristics of landslide materials can be affected by various factors. We examined the shear stress characteristics of two different soils using ring-shear apparatus, in which saturation-consolidation-shearing speed can be easily controlled. This paper presents (i) shear stress-time characteristics, (ii) shear stress depending on normal stress and shear speed and (iii) shear stress as a function of shearing speed. Materials used in this paper were the Nakdong River sand and muds taken from Jinhae coastal area in Korea. Samples were prepared in three types: Sand (upper)-Sand (lower), Clay (upper)-Clay (lower) and Sand (upper)-Clay (lower). The upper and lower indicate the samples placed in upper and lower ring shear boxes, respectively. For given normal stresses (50 and 100 kPa) and shearing speed (0.1 mm/sec), we performed ring shear tests. Then the failure lines were determined in the second test. Last, we determined the shear stress characteristics depending on different shearing speeds, such as 0.01, 0.1, 1, 10, 100 mm/sec. As a result, we found that shear stress characteristics are strongly dependent on above three factors. The shear stress of Sand (upper)-Clay (lower) is smaller than that of Sand (upper)-Sand (lower), but slightly larger than that of Clay (upper)-Clay (lower). The shear stress is also characterized by grain crushing and wetting process at slip surface.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.8
• /
• pp.677-682
• /
• 2015

We simulate an emulsion system under simple shear rates to analyze its rheological characteristics using the lattice Boltzmann method (LBM). We calculate the relative viscosity of an emulsion under a simple shear flow along with changes in temperature, shear rate, and surfactant concentration. The relative viscosity of emulsions decreased with an increase in temperature. We observed the shear-thinning phenomena, which is responsible for the inverse proportion between the shear rate and viscosity. An increase in the interfacial tension caused a decrease in the relative viscosity of the decane-in-water emulsion because the increased deformation caused by the decreased interfacial tension significantly influenced the wall shear stress.

• Journal of the Korean Geotechnical Society
• /
• v.22 no.8
• /
• pp.43-54
• /
• 2006

The scope of this paper covers the applications of bender element tests in consolidation, tomography, and liquefaction. Loading and unloading time during consolidation are evaluated based on shear wave velocity. As S-wave velocity is dependent on effective stress, the loading step may be determined. However, cautions are required due to the different mechanism between the settlement and effective stress criteria. The stress history may be evaluated because the S-wave shows the cement controlled regime and stress controlled regimes. A fixed frame complemented with bender elements permits S-wave tomography The tomography system is tested at low confinement within a true triaxial cell. Results show that shear wave velocity tomography permits monitoring changes in the velocity field which is related to the average effective stress. To monitor the liquefaction phenomenon, S-wave trans-illumination is implemented with a high repetition rate to provide detailed information on the evolution of shear stiffness during liquefaction. The evolution of shear wave propagation velocity and attenuation parallel the time-history of excess pore pressure during liquefaction. Applications discussed in this paper show that bender elements can be a very effective tool for the detection of shear waves in the laboratory.

• Tunnel and Underground Space
• /
• v.17 no.3 s.68
• /
• pp.203-215
• /
• 2007

Stability and mechanical deformation behavior of rock masses are highly dependent on the mechanical characteristics of contained discontinuities. Therefore, mechanical characteristics of the discontinuities should be considered in the design of tunnel and underground structures. In this study, direct shear tests for rough granite joints were carried out under constant normal stiffness conditions. Effects of initial normal stress, shear velocity, and surface roughness on the characteristics of shear strength and deformation behaviors were examined. Results of shear testing under constant normal stiffness conditions reveal that shear behaviors could be classified into two categories, based on the amount of decrease in shear stress at the Int peak shear stress. With initial normal stiffness increasing, it turned out that shear displacement at peak stress and the first peak shear stress increased, however friction angle and friction coefficient showed decrease. In case of shear stiffness and average friction coefficient, it turned out that they are not dependent on the initial normal stress. Minor effects of shear velocity on rough joints were observed in several shear quantities. However, the effects of shear velocity were insignificant regardless of the normal stress increase. Change of shear strength and deformation characteristics on joint roughness were examined, however, it turned out that the variations were attributed to deviation of shear test specimens.