• The Korean Journal of Rheology
• /
• v.10 no.1
• /
• pp.24-30
• /
• 1998

솔젤법을 이용하여 단분산의 실리카 입자를 제조하고 농도변화에 따른 실리카 분산 액의 유변학적 거동을 해석하였다. 단분산 실리카 입자의 제조는 솔젤법을 이용한 액상반으 으로 제조하였고 입자의 안정화를 위하여 입자표면에 실란커플링제를 코팅하여 유기용매에 서 안정성을 갖도록 하였다. 분산액의 농도에 따른 유변학적 거동을 조사하기 위하여 부피 분율( )이 0.05인 희박 분산계로부터 =0.55의 고농도 분산계를 제조하였다. 솔젤법을 통하 여 단분산 실리카 입자를 성공적으로 제조하였으며 실란커플링제인 ${\gamma}$-methacryloxypropyl triethoxysilane로 입자의 표면을 화학적 방법으로 처리하여 유기용매 상에서 알킬기의 작용 에 의한 hard-sphere'특성을 나타내도록 하였으며 동시에 분산안정성을 유지할수 있었다. 입자 분산계는 =0.25이하의 부피농도에서는 분산용매와 같은 뉴톤거동을 보여주었으며 이 이이상의 농도에서는 비뉴톤거동인 전단담화(shear thinning)현상과 high shear limiting viscosity를 나타내었다. 이결과는 Krieger-Dougherty 식을 따름이 확인되었으며 부피분율 =0.50정도까지도 이식이 잘적용됨을 확인하였다. 부피분율 =0.50 이상의 고농도 입자 분산계 는 급격한 점도의 증가와 함께 전단담화와 전단탁화(shear thickening)현상이 모두 관찰되었 다. 특히 전단탁화를 일으키는 특헝전단변형률(cr)이하의 전단변형률에서는 안정되고 빠른 점성반응(viscous response)을 보여주었으나 특성 전단변형률 부근과 이상의 전단변형률 영 역에서는 매우 불안한 거동이 보여짐을 확인하였다. 그러나 이러한 점도 거동은 가역적이며 전단변형률을 증가시킬때와 감소시킬 때의 유변학적 거동이 거의 일치하였다.

• Journal of the Korean Geotechnical Society
• /
• v.27 no.6
• /
• pp.49-61
• /
• 2011

This paper presents the applicability of rheological models for describing fine-laden debris flows and analyzes the flow characteristics as a function of grain size. Two types of soil samples were used: (1) clayey soils - Mediterranean Sea clays and (2) silty soils - iron ore tailings from Newfoundland, Canada. Clayey soil samples show a typical shear thinning behavior but silty soil samples exhibit the transition from shear thinning to the Bingham fluid as shear rate is increased. It may be due to the fact that the determination of yield stress and plastic viscosity is strongly dependent upon interstructrual interaction and strength evolution between soil particles. So grain size effect produces different flow curves. For modeling debris flows that are mainly composed of fine-grained sediments (<0.075 mm), we need the yield stress and plastic viscosity to mimic the flow patterns like shape of deposition, thickness, length of debris flow, and so on. These values correlate with the liquidity index. Thus one can estimate the debris flow mobility if one can measure the physical properties.

• Journal of the Korean Geotechnical Society
• /
• v.27 no.10
• /
• pp.81-92
• /
• 2011

The rheological properties of Wyoming bentonites are strongly influenced by the size of particles, cation exchangeable capacity, arrangement and morphology of clay mineral. This paper presents the results of rheological investigations on the Wyoming bentonites aqueous dispersions: two types of particle flocculation were considered. For the Wyoming bentonite, 0g/L and 30g/L NaCl equivalent salinity were added in fresh and salt water to examine the rheological behavior. This paper examined the general rheological characteristics, compatibility of rheological models and correlation between soil structure and change in rheological properties of Wyoming bentonite caused by increasing salinity. From flow curves of bentonites hydrated with fresh water and salt water, the observed general flow behavior is very close to shear thinning with yield stress (or ideal Bingham fluid with yield stress and plastic viscosity). However, the change of shear stress at the same shear rate is clear, particularly for lower shear rate. Well-known rheological models are used to fit the data. There is a good agreement between rheological model and data: Carreau, Herschel-Bulkley and power-law for S=0g/L and bilinear, Herschel-Bulkley and power-law for S=30g/L. It may be due to the fact that the internal structural bonding (strong modification of particle-particle interactions from edge-to-edge and/or edge-to-face to face-to-face) in soil matrix is affected from the evolution of rheological properties with different salinities.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.2048-2053
• /
• 2003

The present study investigated the effect of the transversal vibration on the flow characteristics for non-Newtonian fluids. The effect was tested by experiment and numerical analysis. For Newtonian fluids, both of experiment and numerical analysis results showed that mechanical vibration did not affect the flow rate. For non-Newtonian fluids, however, there was significant disagreement between experiment and numerical results. The numerical results showed a negligibly small effect of vibration on the flow rate whereas experimental results showed a significant flow rate increase associated with transversal vibration. The results implied that the increased flow rate was caused not only by imposed shear rates at the wall but also by the changes of rheological characteristics due to the transversal vibration.

• The Korean Journal of Rheology
• /
• v.10 no.1
• /
• pp.7-13
• /
• 1998

중량 평균 분자량이 1.22$\times$106이고 다분산도가 8.90이며 수분과 아밀로오스 함량이 각각 9.35%, 27%인 도토리 전분에 sucrose를 첨가하여 동적 유변학적 특성에 대한 온도와 농도의존성을 고찰하였다. AS(acorn starch)-sucrose 계의 점도는 전단속도가 증가하면 감 소하는 전단담화 현상을 나타내며 sucrose 농도가 증가할수록 점도가 증가하였고, Casson 식에 의해 얻어진 항복치는 sucrose 농도가 증가하면 증가하였다. 저장영률과 손실영률은 sucrose 농도가 증가하면 단일하게 증가하였고 손실 탄성률은 온도가 증가하면 감소하였다. DSC 측정자료를 zipper model에 적용시켜 본 결과 sucrose 농도가 증가할수록 zipper의 수 와 junc-tion zone의 수는 증가했으며 크기는 감소하였다. Sucrose는 전분과 수소결합을 형 성하여 용액내에서 가소제처럼 거동함을 알수있었다.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.34 no.4
• /
• pp.1227-1240
• /
• 2014

Abandoned mines often cause environmental problems, such as alteration of landscape, metal contamination, and landslides due to a heavy rainfall. Geotechnical and rheological tests were performed on waste materials corrected from Imgi waste rock dump, located in Busan Metropolitan City. Debris flow mobility was examined with the help of 1-D BING model which was often simulated in both subaerial and subaqueous environments. To determine flow curve, we used a vane-penetrated rheometer. The shear stress (${\tau}$)-shear rate (${\dot{\gamma}}$) and viscosity(${\eta}$)-shear rate (${\dot{\gamma}}$) relationships were plotted using a shear stress control mode. Well-known rheological models, such as Bingham, bilinear, Herschel-Bulkley, Power-law, and Papanastasiou concepts, were compared to the rheological data. From the test results, we found that the tested waste materials exhibited a typical shear shinning behavior in ${\tau}$-${\dot{\gamma}}$ and and ${\eta}$-${\dot{\gamma}}$ plots, but the Bingham behavior is often observed when the water contents increased. The test results show that experimental data are in good agreement with rheological models in the post-failure stage during shearing. Based on the rheological properties (i.e., Bingham yield stress and viscosity as a function of the volumetric concentration of sediment) of waste materials, initial flowing shape (5 m, 10 m, and 15 m) and yield stress (100 Pa, 200 Pa, 300 Pa, and 500 Pa) were input to simulate the debris flow motion. As a result, the runout distance and front velocity of debris flow are in inverse propositional to yield stress. In particular, when the yield stress is less than 500 Pa, most of failed masses can flow into the stream, resulting in a water contamination.

• Korean Chemical Engineering Research
• /
• v.49 no.3
• /
• pp.314-319
• /
• 2011

In this study, the flow behavior of Newtonian and non-Newtonian coating liquids inside slot die has been scrutinized for the purpose of optimal internal die design in slot coating system from three-dimensional computations by CFD Fluent solver. A hybrid slot die could be optimally designed by changing the chamber or manifold structure to guarantee the uniform velocity distribution of coating liquids at die exit. Especially, for the non-Newtonian coating liquids, the length of coat-hanger for the uniform coating has been properly chosen, according to the degree of their shearthinning properties.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.46 no.6
• /
• pp.771-777
• /
• 2017

This study investigated the rheological properties of Calrose rice flour dispersions as well as the effects of different thawing methods (steamer, smart oven, and microwave oven) on quality characteristics of frozen turmeric rice. Apparent viscosity, consistency index, and yield stress significantly increased at higher rice flour concentrations. Magnitudes of storage modulus and loss modulus significantly increased with elevation of rice flour concentration. Frozen turmeric rice thawed using a steamer had the highest moisture content and largest size (length, width, and thickness) among all thawing methods. The L values of turmeric rice after thawing using a steamer was significantly higher than those of other thawing methods. The a value of turmeric rice after thawing using a steamer was significantly lower than those of other thawing methods. Textural properties (hardness, adhesiveness, springiness, cohesiveness, brittleness, and chewiness) of frozen turmeric rice after thawing using a steamer were significantly lower than those of other thawing methods. Therefore, it can be concluded that frozen turmeric rice after thawing using a steamer might be desirable for improvement of texture.

• Polymer(Korea)
• /
• v.37 no.4
• /
• pp.494-499
• /
• 2013

Modified polypropylene (m-PP) was fabricated by furfuryl sulphide (FS) as branching agent and m-PP/nano-filler composites were prepared with silicate and multi-walled carbon nanotube (MWCNT), using a twin screw extruder. The chemical structures and thermal properties of the m-PP were investigated by FTIR and DSC. The chemical structure of the m-PP was confirmed by the existence of =C-H stretching peak of the branching agent at 3100 $cm^{-1}$. There was no district change in melting temperature in case of m-PP, but a certain increase in crystallization temperature was notified and the increase was in the range of $10-20^{\circ}C$. The rheological properties, filler dispersion and foaming behaviors of the m-PP/nano-filler composites were investigated by dynamic rheometer, X-ray diffractometer (XRD) and scanning/transmission electron microscope (SEM/TEM). m-PP/nano-filler composites showed a high complex viscosity at a low frequency, an increase in melt elasticity, and a high shear thinning effect. Compared to pure PP, m-PP and m-PP/nano-filler composites were sufficient to enhance the foaming behavior.

• Applied Chemistry for Engineering
• /
• v.22 no.6
• /
• pp.679-684
• /
• 2011

Branched polypropylenes (LCB-PP) with a long chain branch were prepared by the solid-state and molt-state reaction. Divinylbenzene (DVB), 1,4-benzenediol (RES), and furfuryl sulphide (FS) were used as branching agents of fabricate LCB-PP/silicate composites. Chemical structures, thermal properties, and rheological properties of the LCB-PP were determined by FT-IR, DSC, TGA, and dynamic rheometer (ARES). The chemical structure of the LCB-PP was confirmed by the existence of =C-H stretching peak of the branching agent at $3100cm^{-1}$. From DSC and TGA results, the melting reaction was more effective than the solid state reaction in the manufacture of LCB-PP, which was additionally certified by rheological properties. Based on rheological properties, FS was the best for branching efficiency of PP. Compared to PP, LCB-PPs indicated an increase of complex viscosity in the low frequency and shear thinning tendency, and G'-G" plot represented an increase in elasticity and the heterogeneousness in a melt state. Rheological properties of LCB-PP/silicate composites were observed with the silicate content. When 5 wt% silicate was added in LCB-PP, distinct changes in the shear thinning and the slope of G'-G" plots were observed.