• Journal of Adhesion and Interface
• /
• v.7 no.2
• /
• pp.26-31
• /
• 2006

In order to effectively improve interfacial adhesion strength between polypropylene (PP) and jute fiber, we particularly incorporated maleic anhydride grafted PP (MAPP) into the matrix through the environment-friendly process without an additional method of process and had better mechanical performances by providing the alignment into the natural fiber than those of the conventional fabrication technology such as an extrusion or injection molding. We also proposed hot pressing method which applied relatively low shear to the composites and confirmed the chemical bonds among the functional groups of MAPP and jute using FT-IR approach. The concentration of MAPP for maximum tensile strength and modulus was optimized at 3 wt%. Flexural properties had no noticeable tendency to increase with MAPP contents compared to tensile strength, which could probably be explained by the degree in wetting of PP/MAPP matrix.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.27 no.1
• /
• pp.19-29
• /
• 2023

An ultra-high strength prestressed prismatic beam of 100 MPa in compressive strength was developed by increasing the watertightness of concrete by utilizing centrifugal molding processes without adding expensive admixtures such as silica fume. The ultra-high strength centrifugal shaped square beam installed on the wall is composited with the upper slab concrete and then subjected to a service load. Horizontal shear stress is generated by bending between the centrifugal molding beam and the floor plate, which causes the beam and floor plate to perform composite behavior through shear connections such as studs and rebars. In this study, a flexural load test was performed on a mock-up specimen that was synthesized by fabricating an RC slab on top of a 100 MPa-class centrifugal shaped beam produced at the factory. proven reliability.

• Clean Technology
• /
• v.15 no.3
• /
• pp.180-185
• /
• 2009

The ethylene-propylene rubber (EPDM) scrap generated from automobile weatherstrip manufacturing process was used to make a thermoplastic elastomer through blending with polypropylene. The surface activated EPDM powder was obtained by the high temperature and shear pulverizer. The addition of surfactant resulted in more surface activated EPDM powder and the optimum loading amounts of surfactant was 1.5 phr. Maleic anhydride was grafted onto polypropylene by reactive blending to give functionalized polypropylene. The wetting property between EPDM scrap and polypropylene was improved by the addition of poly (ethylene-co-acrylic acid) as a compatibilizing agent. Poly(ethylene-co-acrylic acid) decreased the surface tension of polypropylene and thus would contribute to the wettability with EPDM powder.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.28 no.3
• /
• pp.27-36
• /
• 2024

This study established a BIM procedure considering manufacturing errors in the production process, and evaluated the flexural ductility of precast all-lightweight aggregate concrete special shear walls (PLASWs) with spliced sleeve technique. In the production process, the concrete cover thickness of PALSW was on average 1.28 times greater than the cross-sectional details of the specimen modeled with Revit BIM program. In particular, the bending inner radius of the hoop and inner-cross tie were greater than the designed details. Consequently, the confinement effect of core concrete reduced from 64% to 54% due to the manufacturing errors in the transverse reinforcing bars, resulting in a decrease in the ductility of PALSW by approximately 4.91%. Considering these findings, the BIM of PLASW with spliced sleeve technique should compliment the bending inner radius of the transverse reinforcing bars, and the defined brittleness increase coefficient reflecting the decreased core concrete confining pressure in the stress-strain relationship of confined concrete should be evaluated as 1.8.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2001.11a
• /
• pp.127-127
• /
• 2001

종이의 공극은 도공용 원지 또는 인쇄 용지로 사용될 때 도공액과 잉크 조성분의 침 투 거동에 영향을 미침으로써 여러 가지 물리적 성질에 변화를 가져온다. 도공 공정의 경우, 도공액에 포함되어 있는 물과 수용성 고분자 물질의 원지 침투는 도공 작업성과 도공층의 구조에 변화를 가져 올 수 있다. 이러한 변화는 물을 포함한 수용성 물질의 원지 침투가 빨라질 때 도공액의 고형화점 상승에 의한 원지 피복력 저하에 따른 도공 지의 평활성 감소를 가져온다. 또한 높은 전단력이 가해지는 블레이드 도공에서는 도피 직전 도공액의 수분 이탈이 급격하게 일어날 경우 블레이드에서 도공액의 유동성 저하 가 발생됨으로써 여러가지 문제점을 나타낸다고 보고 된 바 있다. 인쇄 공정의 경우에 는 도공층이 잉크의 직접적인 기질(substrate)로 작용되어 잉크 성분의 잔류 및 침투 거동에 영향을 미친다. 즉 지나치게’발달된공극 특성을 지닌 도공층에서는 잉크 안료가 적절한 결합력을 가지고 도공층에 정착되기 전에 잉크 속의 레진과 용제가 도공층의 공극으로 소실됨으로써 인쇄 완료 후 작은 외력에도 잉크 층이 파괴되는 효킹 ( (chalking) 현상이 일어난다. 그러나 과도한 바인더의 적용과 미세한 안료의 사용에 따 라 도공층의 공극이 폐쇄될 경우에는 인쇄 후 잉크의 건조가 늦어져 인쇄 작업성의 저 해 요인으로써 작용한다. 종이의 공극성과 인쇄적성은 주지하는 바와 같이 불가분의 관계에 있으며, 본 연구에 서는 피인쇄체로서 공극성을 달리한 세 종류의 도공지를 제조하고 실험실적으로 제조 된 잉크를 사용하여 각각의 특성에 따른 잉크의 잔류 특성에 대하여 고찰해 보고자 하 였다. 특히 인쇄 전 피인쇄체의 공극 특성에 따른 인쇄 전후의 공극율 변화와 주요 인 쇄 적성간의 관계에 대해 초점을 맞추었다.시아노에틸화한 PYA용액의 점탄성 평가를 위하여 storage modulus와 loss modulus 를 분석하였다. 일반적 유변특성 평가 결과 PYA용액은 shear-thinning, pseudoplastic 한 특성을 나타내어 표면사이즈 공정에서의 적용 가능성을 확인할 수 있었다. 사용하는 통계기법 중의 하나인 주성분회귀분석을 실시하였다. 주성분 분석은 여러 개의 반응변수에 대하여 얻어진 다변량 자료의 다차원적인 변 수들을 축소, 요약하는 차원의 단순화와 더불어 서로 상관되어있는 반응변수들 상호간 의 복잡한 구조를 분석하는 기법이다. 본 발표에서는 공정 자료를 활용하여 인공신경망 과 주성분분석을 통해 공정 트러블의 발생에 영향 하는 인자들을 보다 현실적으로 추 정하고, 그 대책을 모색함으로써 이를 최소화할 수 있는 방안을 소개하고자 한다.금 빛 용사 둥과 같은 표면처리를 할 경우임의 소재 표면에 도금 및 용 사에 용이한 재료를 오버레이용접시킨 후 표면처리를 함으로써 보다 고품질의 표면층을 얻기위한 시도가 이루어지고 있다. 따라서 국내, 외의 오버레이 용접기술의 적용현황 및 대표적인 적용사례, 오버레이 용접기술 및 용접재료의 개발현황 둥을 중심으로 살펴봄으로서 아직 국내에서는 널리 알려지지 않은 본 기 술의 활용을 넓이고자 한다. within minimum time from beginning of the shutdown.및 12.36%, $101{\sim}200$일의 경우 12.78% 및 12.44%, 201일 이상의 경우 13.17% 및 11.30%로 201일 이상의 유기의 경우에만 대조구와 삭제 구간에 유의적인(p<0.05) 차이를 나타내었다.는 담수(淡水)에서 10%o의 해수(海水)로 이주된지 14일(日) 이후에 신장(腎臟)에서 수축된 것으로

• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.12
• /
• pp.2125-2134
• /
• 2000

This research was to develope the economical treatment processes of the landfill leachate to meet the legal discharge standards. To achieve this purpose, experiments were conducted in laboratory to choose the optimum process and to obtain the design factors before a pi!ot-scale test. The concept of the process developing in this research was using the reverse osmosis system. The submerged membrane bio-reactor was used to achieve pre-treatment of reverse osmosis system and the concentrate was treated by evaporator with land fill gas as a fuel. The results of the research showed that SS, $BOD_5$, $COD_{cr}$, $NH_4{^+}-N$ and T-N were removed 99.0%, 43.0%, 12.9%, 48.5% and 18.7% respectively in the submerged membrane bio-reactor. The reverse osmosis system could remove $BOD_5$, $COD_{cr}$, $NH_4{^+}-N$ and T-N as an efficiency of97.5%, 97.6%, 79.7% and 85.4% respectively. The evaporator could remove $COD_{cr}$, $NH_4{^+}-N$ and T-N as an efficiency of 90.5%, 50.6% and 63.3% respectively. However the condensed water of the evaporator was not satisfied the legal standard and should be treated in reverse osmosis with the pre-treated leachate.

• Resources Recycling
• /
• v.15 no.5 s.73
• /
• pp.26-32
• /
• 2006

The waste solution discharged from the LCD manufacturing process contains acids like nitric, acetic and phosphoric acid and metal ions such as Al, Mo and other impurities. It is important to remove impurities less than 1 ppm in phosphoric acid to reuse as an etchant because the residual impurities even in sub-ppm concentration in semiconductor materials play a major role on the electronic properties. In this study, a mixed system of solvent extraction, diffusion dialysis and ion-exchange was developed to commercialize in an efficient system fur recovering the high-purity phosphoric acid. By vacuum evaporation, almost 99% of nitric and acetic acid was removed. And by solvent extraction method with tri-octyl phosphate (TOP) as an extractant, the removal of acetic and nitric acid from the acid mixture was achieved effectively at the ratio A/O=1/3 with 4th stage of extraction stage. About 97.5% of Al and 36.7% of Mo were removed by diffusion dialysis. Essentially almost complete removal of metal ions and purification of high-purity phosphoric acid could be obtained by using ion exchange.

• Journal of Korean Society of Environmental Engineers
• /
• v.32 no.9
• /
• pp.887-893
• /
• 2010

Role of the perforated pipe is to drain the water with equal pressure and velocity through the holes of perforated pipe. The perforated pipe is being used in many processes of water treatment system, however, the design parameter of perforated pipe is not standardized in korea. In this study, we have found the design parameter of perforated pipe in the water treatment system using the Computational Fluid Dynamics (CFD). The uniformity of outflow from the perforated pipe is directly affected according to area ratio (gross area of holes/surface area of the perforated pipe). In other words, the uniformity of outflow is improved as area ratio is smaller. Also, at the same area ratio, the uniformity of outflow is improved as number of holes is increase. Specially, in case of the two holes per length of pipe diameter (2/D) shows the most uniformity of outflow and the best hydraulic with the smaller pressure drop. When the inlet velocity of pipe is about 0.06m/sec, the flux of pipe has decreased as from front to backward. When the inlet velocity is 3 m/s, the flux of pipe has increased as from front to backward.

• Proceedings of the Korean Institute of Resources Recycling Conference
• /
• 2006.05a
• /
• pp.90-94
• /
• 2006

The waste solution discharged from the LCD manufacturing process contains acids like nitric, acetic and phosphoric acid and metal ions such as Al, Mo and other impurities. It is important to removal of impurities to tess than 1ppm in phosphoric acid to reuse as an etchant because the residual impurities even in sub-ppm concentration in semiconductor materials play a major role on the electronic properties. In this study, we have been clearly established that a mixed system of solvent extraction, diffusion dialysis and ion-exchange technique, which made individually the most of characteristics is developed to commercialize in an efficient system for recovering the high-purity phosphoric acid. By applying vacuum evaporation, the yield of the process are almost 99% removal of nitric acid and acetic acid was achieved. And by applying the solvent extraction method with tri-octyl phosphate(TOP) as an extractant, the removal of acetic and nitric acid from the acid mixture was achieved effectively at the ratio O/A=1/3 with four stages and the stripping of nitric acid from organic phase is attained at a ration of O/A=1 with six stages by distilled water. About 97% and 76% removal of Al and Mo were achieved by diffusion dialysis. Essentially complete less than 1ppm removal of Al, Mo by using ion exchange ion resin and purification of the phosphoric acid was obtain.

• Korean Journal of Poultry Science
• /
• v.46 no.2
• /
• pp.95-103
• /
• 2019

This study investigated the effect of traditional medicinal plants on the quality characteristics of Samgyetang breast meat and broth. The traditional medicinal plants used in this study were roots of Panax ginseng, Codonopsis lanceolata, Platycodon grandiflorum, Salvia miltiorrhiza, Adenophora triphylla, and Allium hookeri. There was no significant difference (P>0.05) in the moisture, protein, ash content, water holding capacity, and cooking loss of Samgyetang meat with the addition of traditional medicinal plants. The color values (lightness, redness, and yellowness) of Samgyetang meat and broth were significantly different (P<0.05); the 2-thiobarbituric acid reactive substances and shear force of Samgyetang meat were significantly different (P<0.05); and the pH, turbidity, and viscosity of Samgyetang broth were also significantly different (P<0.05) with the addition of traditional medicinal plants. In the overall acceptability of Samgyetang meat, the addition of S. miltiorrhiza showed the highest score compared to that of other treatments (P<0.05). Thus, the addition of traditional medicinal plants in the production of Samgyetang were found to affect the lipid rancidity beneficially with plant species when compared to Samgyetang with Panax ginseng. In conclusion, with the development of Samgyetang using S. miltiorrhiza, it will be possible to develop products with superior quality characteristics in antioxidant, shear force, and overall acceptability.