• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.416-417
• /
• 2007

MmSH injection molding method to fabricate light guiding plate with nano-sized pattern was developed. A stamper was fabricated through photolithography, dry etching, and electroplating processes. While the stamper with nano-sized pattern in mold was kept at $180^{\circ}C$ during injection process, that was cooled down to $90^{\circ}C$ quickly after the injection process. The nano-sized pattern on light guiding plate processed by MmSH injection molding method was well transferred from stamper compared to that processed by conventional injection molding process.

• Composites Research
• /
• v.23 no.3
• /
• pp.58-63
• /
• 2010

Tensile and flexural properties and electrical conductivity of MWCNT/epoxy composites with different aspect ratios of MWCNTs were compared. The MWCNT/epoxy mixtures were prepared by mechanical dispersion methods using a homomixer and a three-roll mill, and then composite samples were fabricated by compression molding process. The fractured surfaces of the samples were observed by SEM in order to evaluate the degree of dispersion of MWCNTs. The addition of MWCNTs into epoxy resin improved its tensile strength by 7.0% while its flexural strength increased slightly as compared with the one without MWCNTs. In the case of MWCNTs having highest aspect ratio, the mechanical properties of the composites were decreased. When the contents of CM-95 MWCNTs were varied, maximum of tensile and flexural strengths occurred at 1wt% and 0.5wt%, respectively. From the higher contents than these, tensile and flexural strengths of the composites decreased. Electrical conductivities of in-plane and thought-the-thickness directions of MWCNT/epoxy composites were measured using a two-point probe method. They increased with the increase of the aspect ratios and concentrations of MWCNTs in the epoxy matrix.

• Journal of the Korean Ceramic Society
• /
• v.34 no.10
• /
• pp.1083-1091
• /
• 1997

As one of the chemical powder fabrication methods, the powder preparation method by using oxalate has the following advantages; (1) easy to control the chemical stoichiometry, (2) easy to fabricate homogeneous and fine particles, and (3) easy to be thermaly decomposed at low temperature. In the present study, the initial morphology and size distribution of the powder were controlled and the homogeniaty was improved. By carefully controlling the pH with NH4OH, the Bi(Pb)-Sr-Ca-Cu-O superconducting powders were prepared and investigated for their properties. The microstructures and the superconducting properties of the pelletized samples were investigated. Also, the microstructures and electrical properties of the samples prepared by tape casting method were investigated. The fabricated powders were spherical with less than 400 nm, but most of them were agglomerated to be 1~3 ${\mu}{\textrm}{m}$ in size. The critical temperature of the pelletized sample annealed at 84$0^{\circ}C$ for 72 hours in air was 110K. And the critical currents of annealed samples in air prepared by tape casting process for 24 hours and 72 hours were 0.6 A (Jc=600A/$\textrm{cm}^2$) and 1.9A (Jc=1, 900A/$\textrm{cm}^2$) respectively.

• Journal of the Korean Electrochemical Society
• /
• v.10 no.1
• /
• pp.7-13
• /
• 2007

We synthesized and investigated $La_{0.75}Sr_{0.25}FeO_3$ by Glycine Nitrate Process(GNP) method used as cathode materials for SOFC(solid oxide fuel cell). Optimized amount of glycine is 3.17 mol. ICP elemental composition analysis indicated that the stoichiometry of the synthesized powders have nearly nominal values. SEM images and XRD patterns reveal that the synthesized powder has uniform size distribution and high degree of crystallinity. The sample powders were isostatically pressed to form a pellet. The green body was sintered at $1200^{\circ}C$ and the relative density of the sintered specimens were measured by Archimedes mettled. We measured electrochemical performance of LSF by AC impedance spectroscopy. Resistance of LSF shows lower value than that of LSM throughout all temperature region. The anode-supported solid oxide fuel cell showed a performance of $342mW/cm^2(0.7V,\;488mA/cm^2)$ at $750^{\circ}C$. The electrochemical characteristics of the single cell were examined by at impedance method.

• Journal of the Korean Ceramic Society
• /
• v.39 no.9
• /
• pp.822-828
• /
• 2002

Fabrication and electrical characterization of R. F. High-power unit capacitors were investigated to study on condition of fabrication processing for R. F. High-power unit capacitor and electrical characteristics according to addition of $ZrO_2$. The unit capacitors were fabricated using tape casting. The optimum mixture ratio of dielectrics and mixing binder for the slurry fabrication was 57.5∼60.0: 42.5∼40.0 wt%. The slurry viscosity was 4000∼5000 cps and casting state of green tape fabricated using these slurry was excellent. Optimum stacking was made by 200 kg/$cm^2$ pressure with 80$^{\circ}C$ heating. $ZrO_2$ was added to improve the electrical characteristics of unit capacitor, especially breakdown characteristics. The dielectric constant and loss factor of the unit condenser having different $ZrO_2$ amounts was not changed in the addition range of 1 to 5 wt%. Also, dielectric constant was not changed in the frequency range of 10 to 500 kHz. It was found that characteristics of resistance voltage was improved through the formation of $CaZrO_3$ and the reduction of particle size as about 3wt% $ZrO_2$ was added.

• Journal of the Korean Electrochemical Society
• /
• v.8 no.2
• /
• pp.77-81
• /
• 2005

Porous-composite electrodes have been developed using silica gel, which reduce carbon aerogel usage with high cost. Silica gel powder was added to the carbon aerogel to simplify the manufacturing procedure and to increase the wet-ability, the mechanical strength and the CDI efficiency. Porous composite electrodes composed of carbon aerogel and silica gel powder were prepared by paste rolling method. Carbon aerosol composite electrodes with $10\times10cm^2$ are placed face to face between spacers, and assembled the four-stage series cells for CDI process. Each stage is composed of 45 cells. Four-stage series cells (flow through cells) for CDI process are put in continuous-system reactor containing 1,000ml-NaCl solution bath of 1,000 ppm. The four-stage series cells with carbon aerogel electrodes are charged at 1.2V and are discharged at 0.001V, and then read the current. Conclusively, removal efficiencies of ions using the four-stage series cells composed of carbon aerogel composite electrodes show good removal efficiency of $99\%$ respectively.

• Journal of Chest Surgery
• /
• v.33 no.11
• /
• pp.881-885
• /
• 2000

배경: 승모판막 질환에 동반된 심방세동의 경우 그 기간이 길면 승모판막 질환을 수술하여도 동성 율동으로 전환될 가능성이 매우 적다. 본 연구는 승모판막 질환에 동반된 심방세동에 대한 변형 Maze 수술후 장기 결과와 심방세도의 재발에 미치는 요인을 조사 하고자 하였다. 대상 및 방법: 1990년부터 1996년까지 승모판막 질환과 동반된 심방세동으로 외과적 요법을 시행받은 35명의 환자를 대상으로 하였다. 심방세동의 평균 유병기간은 평균 7.7$\pm$4.5년이었고 수술은 승모판막 대치술 34례(재수술 3례)와 승모판막 성형술 1례를 시행하였고 승모판 질환 수술 외에 동반 수술로는 삼첨판륜 성형술 4례, 삼첨판막 대치술 3례 였다. 심 방세동에 대한 수술은 좌측 폐정맥 부위는 격리하지 않는 변형 Maze 수술을 시행하였다. 수술 후 동성 율동으로 회복여부, 심방세동의 재발에 미치는 요인과 장기 결과를 분석하였다. 결과: 수술 직후 2례를 제외한 33례(93.9%)에서 동성율동으로 돌아왔으나 수술 후 퇴원 전에 12례에서 심방세동이 재발되었다. 수술환자중 1례에서 수술 후 3일에 동성 정지에 따른 심정지가 발생하여 소생되었으나 뇌손상으로 수술 후 15일에 사망하였다. 심방세동이 재발된 경우 수술 후 약 2개월에서 6개월 사이에 항부정맥 약물(mquinidine)과 전기적 제세동으로 치료하여 12례중 10례에서 동성 율동으로 돌아온 환자는 항부정맥 약물을 모두 중단하 였으며, 수술 후 3년에서 9년(평균 71.1$\pm$17.5개월) 추적 관찰 중 9례에서 심방세동이 재발되어 장기간 동성 율동이 유지된 환자는 34명중 25명으로 73.5%이었다. 승모판 질환이 있던 환자에서 수술 후 심방세동의 재발에 미치는 요인들을 조사한 결과 수술전 심방세동의 기간(동성율동 유지군 : 재발군=6.3년 : 10.3년, P=0.008)과 수술 전 단순 흉부 X선상 심흉비율(0.58 : 0.72, p=0.009)은 통계학적으로 유의하게 나타났으나 심초음파 검사상 좌심방의 직경(57.2mm : 77.4mm, p=0.106)은 통계학적 유의성이 없었다. 결론: 심방세동이 있는 환자에서 동반 질환 수술시 병행하여 수술한다면 정상 동성 율동으로 회복될 기회를 증가시킬 수 있는 유용한 수술법으로 생각된다. 그러나 수술후 재발률을 감소시키기 위하여 적절한 술기의 변형에 대한 연구와 약물요법의 병행을 고려하여야 할 것으로 사료된다.

• Journal of the Institute of Convergence Signal Processing
• /
• v.25 no.1
• /
• pp.39-45
• /
• 2024

Recently, the paradigm of the aircraft industry, not only domestically but also globally, has been changing significantly starting with the era of the Fourth Industrial Revolution. With the convergence of new technologies such as ICT and AI, the drone market, centered around the military, is expanding its overall services to include the civilian market. Additionally, drones operate by being equipped with batteries, and for product lines that use batteries, lightening the product is one of the critical factors. This is because the lighter the aircraft, the less battery consumption and maximum efficiency. Therefore, recently, composite materials have been used to reduce the weight of the aircraft. To not only reduce weight but also achieve high functionality, it is being applied to most areas such as propellers, airframes, interior materials, floor plates, driving devices, and battery housings, and is emerging as a core technology. In this paper will utilize ceramic fiber composite materials, which have recently emerged for lightweight. It aims to improve noise and strength by targeting propellers, one of the most important factors in drones. In addition, the performance of the propeller developed through the low-noise design will be verified.

• Geophysics and Geophysical Exploration
• /
• v.13 no.4
• /
• pp.378-387
• /
• 2010

We present the results of laboratory measurement of porosity and electrical resistivity for the samples collected near marine hydrothermal deposit to provide fundamental perspective of physical properties for future electromagnetic survey. The rock cores are sampled from the host rock, pumice, hydrothermal altered zone, and chimney. These samples are featured as easily brittle, rough surface with large pores, having components easily solvable in the water. We suggest systematic approach for measuring weights, volumes of core samples to calculate density and porosity. Measurements reveal that the resistivities of black host rock, gray host rock, pumice and chimney are 102, 39, 11, 0.1 ohm-m, respectively, when the core samples are saturated with saline water of $32,000\;{\mu}S$/cm (0.5 ohm-m) at temperature of $2.5^{\circ}C$ and these correspond to the factors of 5 for sea water, 110 for pumice and 390~1020 for host rocks with respect to the resistivity of chimney. We also confirm that resistivity of rock samples saturated with water decrease with temperature linearly over the temperature range of $20{\sim}80^{\circ}C$.

• Journal of the Korean Ceramic Society
• /
• v.34 no.2
• /
• pp.115-122
• /
• 1997

The powder preparation by using emulsion drying method, one of the chemical powder fabrication methods has the advantages; easy to control the chemical stoichiometry and to fabricate homogeneously fine particles. In the present study, the initial morphology and size distribution of the powder fabricated by using emulsion dry-ing method were controlled and were improved the homogeneity. By carefully controlling the mixing ratio of oil phase and aqueous solution and surfactant of preventing emulsion separation, the Bi(Pb)-Sr-Ca-Cu-O su-perconducting powders were prepared. The properties of the superconducting powder fabricated by this method and the microstructures and superconducting properties of the pelletized samples were investigated. The microstructures and electric properties of the tapes prepared by oxide powder-in-tube method were in-vestigated. The fabricated powder was spherical with less than 1$\mu$m but most of them was agglomerated with 2~5$\mu$m in size. The critical temperature of the pelletized sample annealed at 84$0^{\circ}C$ for 72 hours in oxygen par-tial pressure of 1/13atm in Ar atmosphere was 108K. And the critical current of the first and second annealed tapes in air prepared by oxide powder-in-tube process were 0.4A and 1.5A, respectively.