• Journal of Bio-Environment Control
• /
• v.22 no.1
• /
• pp.73-79
• /
• 2013

An experiment was conducted to study incidences of heat loss in greenhouse in Gyeongnam province using thermal imaging camera in order to determine ways minimizing greenhouse heat loss. Measurements of this work showed that temperature differences between two experiment zones before and after installation of thermal curtains were about $2.0{\sim}3.0^{\circ}C$ and $1.0{\sim}2.0^{\circ}C$ respectively. There was a high correlation between the temperature data measured using a thermal imaging camera and a temperature sensor. There was no serious difference among areas, but between places on the first and second floor with thermal curtains for heat insulation, there was a relatively larger heat loss on the first floor than the second floor. Then in general the greenhouse types had no particular bearing on this matter, there was a relatively large heat loss in the parts of side wall window, the gaps and the parts folded of horizontal thermal curtains, the gutter parts, and the gaps of thermal curtain in the side wall window and facade back side for heat insulation, aren't completely sealed. It was found that there was a substantial heat loss due to infiltration through cracks on covering material, doors, ventilating openings, roof gables and floors, in particular.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.10a
• /
• pp.55-58
• /
• 2005

During braking at a train, thermal energy is generated due to the frictions between disk and lining and wheel and shoe. In general, the braking transfers the kinetic energy into thermal energy. Therefore, the frictional characteristics are varied according to the braking force, the thermal resistance, and the thermostable, etc. Using a Dynamo testing we have studied the frictional characteristics and the thermal distribution to investigate a stable speed and to improve the testing method through comparing and analysing in the measurement of the thermocouple temperature and infrared camera.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.1537-1538
• /
• 2015

전력사용량이 산업발전과 더불어 기하급수적으로 증가하고 있으며, 한정된 공간내에서 대용량의 전력설비를 설치하기 위해 폐쇄형 배전반이 운영되고 있다. 한국전기안전공사에서 발표한 통계자료에 의하면, 고압이상 전기설비 검사결과 절연내력이 불합격인 경우가 다수 발생하고 있으며, 이는 아크 플래시 사고의 원인이다. 특히 수배전반의 경우 부하설비 또는 외부의 영향을 확인할 수 있는 장치 및 보호설비가 설치되어 있으나 자체 안전장치가 마련되어 있지 않아 자체사고를 신속히 검출하고 판단할 수 있는 기술이 필요하다. 본 논문에서는 해상도가 낮은 저가의 열화상 센서에 고속 DSP를 사용하여 영상처리 기법인 이차원 보간 법으로 해상도를 올려서 사용하는 기술을 이용하여 아크에 의해 발생되는 열특성을 검출하고 검출된 데이터를 전송하여 전기화재사고를 미연에 방지할 수 있는 장치 개발을 위한 기초 특성조사를 실시하였다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.35-36
• /
• 2006

In Nd:YAG laser welding, evaluation methods of welding flaw are various. But, the method due to fume shape is difficult to classification of welding flaw. The Nd:YAG laser process is known to have high speed and deep penetration capability to become one of the most advanced welding technologies. At the present time, some methods are studied for measurement of fume shape by using high-speed camera and photo diode. This paper describes the machining characteristics of SM45C carbon steel welding by use of an Nd:YAG laser. In spite of its good mechanical characteristics, SM45C carbon steel has a high carbon contents and suffers a limitation in the industrial application due to the poor welding properties. In this study, fume shape was measured by infrared thermal camera that is non-contact/non-destructive thermal measurement equipment through change of laser generating power, speed, focus. Weld was performed on bead-on method. Measurement results are compared as two equipments. Here, two results are composed of measurement results of fume quantities due to fume shape by infrared thermal camera and inspection results of weld bead include weld flaws by ultrasonic inspector.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2016.11a
• /
• pp.116.1-116.1
• /
• 2016

반도체 가스센서에서는 가연성 및 탄화수소계 가스를 감지 하기 위해서 $100{\sim}500^{\circ}C$ 이상의 동작온도를 필요로 한며, 이에 따라 반도체식 가스센서의 마이크로 히터 소재는 고온에서 열적 안정성이 있는 소재가 요구된다. 현재 상용화되고 있는 반도체식 가스센서는 실리콘(Silicon) 기반의 MEMS 기술을 이용한 가스센서이며, 구조적으로나 성능적 한계가 드러남에 따라 실리콘 이외의 다양한 재료의 MEMS 응용기술 개발이 필요한 실정이다. 본 연구에서는 이러한 실리콘의 재료적 한계를 극복하기 위해 다공성 알루미늄 산화물(AAO)을 기판으로 사용하여 마이크로 히터를 제작하였다. AAO의 제작에 앞서 CMP, 화학연마, 전해연마를 이용하여 적합한 전처리 공정을 선정하였고, AAO 제작 시 온도, 시간, 전압의 변수를 주어 마이크로 히터 기판에 적합한 공정을 탐색하였다. 마이크로 플랫폼은 MEMS 공정으로 제작되었으며, PR(Photo Resist)을 LPR(Liquid Photo Resist)과 DFR(Dry Film Resist)로 각각 2종 씩 선택하여 AAO에 적합한 제품을 선정하였다. 제작된 마이크로 히터는 $1.8mm{\times}1,8mm$로 소형화 하였고, 열손실의 제어를 위해 열확산 방지층을 추가하였다. 구동 온도, 소비전력, 장시간 구동시 안정성의 측정 및 평가는 적외선 열화상 카메라와 kiethly 2420 source meter를 이용하여 측정하였으며, 열확산 방지층의 유 무에 따른 온도 분포 및 소비전력을 비교평가 하였다. 최종적으로는 현재 사용화 되어있는 가스센서들의 소비전력과 비교 평가 하여 논의 하였다.

• FLOWER RESEARCH JOURNAL
• /
• v.18 no.3
• /
• pp.186-192
• /
• 2010

An infrared heating system, installed in a small venlo-type glasshouse ($280m^2$) in Gyeongsang National University, Jinju, Korea, was used to investigate its heating effect with potted Phalaenopsis, Schefflera arboricola 'Hongkong', Ficus elastica 'Variegata', and Rosa hybrida 'Yellow King' as the test plants. Temperature changes in test plants with the system turned 'On' and 'Off' were measured by using an infrared camera and the consumption of electricity by this infrared heating system was measured and analyzed. In potted Phalaenopsis, when the set air temperature of the greenhouse was $18^{\circ}C$, temperature of leaves and the growing medium were $22.8{\sim}27^{\circ}C$ and $21.3{\sim}24.3^{\circ}C$, respectively. In such tall plants as Schefflera arboricola 'Hongkong' and Ficus elastica 'Variegata', the upper part showed the highest temperature of 24.0 and $26.9^{\circ}C$, respectively. From the results of temperature change measurements, the plant temperatures were near or above the set point temperatures with some fluctuations depending on the position or distance from the infrared heating system. When air temperature between night and dawn dropped sharply, plant temperatures were maintained close to the set temperature ($18^{\circ}C$). There was a significant difference between 'On' and 'Off' states of the infrared heating system in average temperatures of root zone and leaf: 21.8 and $17.8^{\circ}C$ with the system 'On' and 20.4 and $15.5^{\circ}C$ with the system 'Off', respectively, in a cut rose Rosa hybrida 'Yellow King'. The heating load was about $24,850{\sim}35,830kcal{\cdot}h^{-1}$, which comes to about 27,000~40,000 won in Korean currency when calculated in terms of the cost of heating by a hot water heating system heated by petroleum. The cost for heating by the infrared heating system was about 35% of that of a hot water heating system. With the infrared heating system, the air temperature during the night was maintained slightly lower than the set point air temperature, probably due to the lack of air tightness of the glasshouse. Therefore, glasshouses with an infrared heating system requires further investigation including the installation space of the heat-emitting units, temperature sensor positions, and convection.

• Tribology and Lubricants
• /
• v.30 no.2
• /
• pp.124-129
• /
• 2014

The piping system accounts for a large portion of the machinery structure of a plant, and is considered as a very important mechanical structure for plant safety. Accordingly, it is used in most energy plants in the nuclear, gas, and heavy chemical industries. In particular, the piping system for a nuclear plant is generally complicated and uses the reactor and its cooling system. The piping equipment is exposed to diverse loads such as weight, temperature, pressure, and seismic load from pipes and fluids, and is used to transfer steam, oil, and gas. In ultrasound infrared thermography, which is an active thermography technology, a 15-100 kHz ultrasound wave is applied to the subject, and the resulting heat from the defective parts is measured using a thermography camera. Because this technique can inspect a large area simultaneously and detect defects such as cracks and delamination in real time, it is used to detect defects in the new and renewable energy, car, and aerospace industries, and recently, in piping defect detection. In this study, ultrasound infrared thermography is used to detect information for the diagnosis of nuclear equipment and structures. Test specimens are prepared with piping materials for nuclear plants, and the optimally designed ultrasound horn and ultrasound vibration system is used to determine damages on nuclear plant piping and detect defects. Additionally, the detected images are used to improve the reliability of the surface and internal defect detection for nuclear piping materials, and their field applicability and reliability is verified.

• Convergence Security Journal
• /
• v.22 no.2
• /
• pp.21-26
• /
• 2022

Wearing face masks is an effective measure to prevent COVID-19 infection. Infrared thermal image based temperature measurement and identity recognition system has been widely used in many large enterprises and universities in China, so it is totally necessary to research the face mask detection of thermal infrared imaging. Recently introduced MTCNN (Multi-task Cascaded Convolutional Networks)presents a conceptually simple, flexible, general framework for instance segmentation of objects. In this paper, we propose an algorithm for efficiently searching objects of images, while creating a segmentation of heat generation part for an instance which is a heating element in a heat sensed image acquired from a thermal infrared camera. This method called a mask MTCNN is an algorithm that extends MTCNN by adding a branch for predicting an object mask in parallel with an existing branch for recognition of a bounding box. It is easy to generalize the R-CNN to other tasks. In this paper, we proposed an infrared image detection algorithm based on R-CNN and detect heating elements which can not be distinguished by RGB images.

• Journal of Energy Engineering
• /
• v.22 no.2
• /
• pp.105-111
• /
• 2013

The present study has been carried out to reduce the heat loss from a built in refrigerator by using reverse heat loss method to discern the region with larger heat loss. To perform this purpose, an infrared thermographic camera has been used to measure the surface temperature of the refrigerator and tried to improve the heat loss near the ice dispenser. The numerical heat transfer analysis also has been accomplished to clarify the heat transfer mechanism near the ice dispenser. The possible applicable method to reduce heat loss was increasing the curvature radius at the ice dispenser corner. The curvature radius has been changed from 0mm to 40mm to see the effect of the curvature at the corner. From the present research, the optimal curvature radius for the reduction of heat loss at the ice dispenser could be 30mm.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.7
• /
• pp.567-578
• /
• 2015

Single droplet-wall collision heat transfer characteristics on a heated plate above Leidenfrost temperature were experimentally investigated considering the effects of impact velocity. The collision characteristics of the droplet impinged on the heated wall and the changes in temperature distribution were simultaneously measured using synchronized high-speed video and infrared cameras. The surface heat flux distribution was obtained by solving the three-dimensional transient heat conduction equation for the heated substrate using the measured surface temperature data as the boundary condition for the collision surface. As the normal impact velocity increased, heat transfer effectiveness increased because of an increase in the maximum spreading diameter and a decrease in the vapor film thickness between the droplet and heated wall. For We < 30, droplets stably rebounded from a heated wall without breakup. However, the droplets broke up into small droplets for We > 30. The tendency of the heat transfer to increase with increasing impact velocity was degraded by the transition from the rebounding region to the breakup region; this was resulted from the reduction in the effective heat transfer area enlargement due to the breakup phenomenon.