• Journal of the Microelectronics and Packaging Society
• /
• v.4 no.1
• /
• pp.13-18
• /
• 1997

바인다로서 에폭시 수지와 전도성 금속 충전물로서 은분을 그리고 기타 첨가물을 사용하여 패이스트를 제조하고 전도성 후막을 형성한후 이에대한 열화특성으 연구하였다. 후막의 열화특서은 열과 습도에 대한 내구성 평가로써 250$\pm$5$^{\circ}C$의 solder에 의한 solder dipping test 85$^{\circ}C$~-4$0^{\circ}C$의 cycle을 200회실시하여 저항값의 변화를 관찰하는 heat cycle test 95% 상대습도 및 $65^{\circ}C$에서 500시간동안 유지시키는 humidity resistance test를 실시하 였다. 열화시험후의 전기 저항값의 변화는 페이스트에 사용된 은분의 특성에 의존함을 알수 있었다. 사용된 은분의 입도가 작아질수록 즉 비표면적이 커질수록 열화시험 이전의 저항값 도 컸을뿐 아니라 열화의 정도도 증가함을 알수 있었다.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2016.05a
• /
• pp.166-166
• /
• 2016

국내에서는 기후변화로 인해 집중호우 및 태풍 발생이 증가하고 있으며, 이는 자연재해의 발생뿐만 아니라 차량 및 항공 운항의 어려움을 야기한다. 차량 및 항공 운항의 안정성 확보를 위해서는 노면의 마찰저항을 유지하는 것이 중요한데, 강수로 인해 형성되는 수막두께는 노면의 마찰저항을 감소시키므로 포장설계시 고려해야 할 주요소이다. 특히, 물적/인적 이동이 많은 공항은 기상조건에 더욱 취약하며, 기후변화로 인한 강수특성 변화로 활주로의 수막두께 증가 및 운항의 차질이 우려되고 있다. 따라서 본 연구에서는 과거 및 미래 강우조건에 따라 활주로 노면의 수막두께를 산정하고, 기후변화에 따른 수막두께의 변화를 평가하고자 한다. 과거 관측 및 기후변화 시나리오를 이용하여 강우자료를 생산하였고, 이를 강우-유출 모형의 강우 입력 자료로 활용하였다. 과거 강우자료는 인천지점의 기상청 관측자료를 수집하였으며, AR5 RCP 시나리오(RCP4.5, RCP8.5) 기반의 적정 GCMs 결과를 활용하여 미래 강우시나리오를 산정하였다. 강우의 재현기간 및 지속시간에 따른 수막두께의 변화를 분석하기 위해 인천지역의 과거 및 미래 확률강우량을 산정하였다. 수막두께를 산정하기 위해 활주로 폭, 경사 등 활주로 제원을 수집하고, 유출 모형의 입력자료를 구축하였다. 과거 및 미래 확률강우량을 SWMM 모형에 적용하여 유출량을 산정하였으며, 유속과 흐름폭으로 나누어 활주로의 수막두께를 산정하였다. 산정결과, 강우량이 증가함에 따라 수막두께는 증가하고, 강우의 지속시간이 증가함에 따라서는 감소하는 것으로 분석되었다. 미래의 경우, 기후변화의 영향에 따라 강수량이 증가하여 수막두께가 과거에 비해 증가하였다.

• Proceedings of the KWS Conference
• /
• 2004.05a
• /
• pp.333-335
• /
• 2004

현재 저항 점 용접 공정에서 기존의 공기 가압 장치에서 서보모터를 이용한 서보 가압 장치로 변화가 진행되고 있다. 특히 마이크로 접합부의 경우 그 대상부가 미소ㆍ미세하기 때문에 접합부의 두께, 변형량, 접합후 전기 저항의 크기 둥이 크게 문제가 될 수 있다. (중략)

• Journal of Korean Ophthalmic Optics Society
• /
• v.11 no.3
• /
• pp.225-229
• /
• 2006

In our angle configuration, several peculiar characteristic behaviors of MR could be observed, the mixing of positive MR(PMR) and negative MR(NMR) in the inclined sample was observed. The complete mixing angle, ${\phi}_{mix}$ as a function of inclination angle, ${\theta}$ was observed to fit well to the relation of ${\phi}_{mix}=tan^{-1}(1+tan{\theta})$ in nickel films. The above theoretical relation was obtained by decomposing the magnetic field into the components parallel and perpendicular to the current flow and identifying ${\phi}_{mix}$ as the angle satisfying that the above two components of magnetic field were identical. We also observed that the data of ${\phi}_{mix}$ did not satisfy the above theoretical relation in the iron film. This was explained by the fact that the growth direction in the iron film was an intermediate direction of magnetization, while the growth direction in the nickel film was an easy axis of magnetization.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.30 no.4
• /
• pp.347-351
• /
• 1985

The effect of leaf water content on apparent photosynthesis and respiration of tobacco plants(five varieties) was studied under the condition without the irrigation for 10 days after the plants were sufficiently watered on the first day. The wild race (N. longiflora) among varieties showed highest apparent photosynthesis (AP) and AP had a positive correlation with specific leaf weight. N. longiflora and Andongyeob were different in their AP from the other varieties significantly under the water stress condition. Respiration rate also decreased to be simillar to AP except slight increase at early stage of water deficit. The stomatal resistance and the mesophyll resistance increased in the stressed plants. The water stress resistant character seems to be mainly due to open stomata.

• Journal of the Korean Vacuum Society
• /
• v.5 no.3
• /
• pp.258-262
• /
• 1996

We have investigated the changes in magnetoresistive characteristics, interfacial roughness, and preferred orientation with the Fe buffer layer thickness, annealing temperature, and the stacking number of layers variation in Fe/[NiFe/Cu] multilayers by using the 3-gun d.c. magnetron sputtering method. Intensity of the (200) orientation was increased with the increment of the Fe-buffer layer thickness. We found a maximum magnetoresistance ration of 4.7%, when the buffer layer thickness was 70$\AA$, and the field sensitivity also showed a maximum value at the same thickness. We varied the stacking number of multilayers with fixing the Fe buffer layer thickness of 70$\AA$. When the stacking number was 40 layers, maximum MR ratio(5.3%) was observed. With the variation of annealing temperature no change in the MR ratio was found beyond $300^{\circ}C$. But decrement of MR ratio was observed above $300^{\circ}C$. This decrement of the MR ratio was responsible for the increment of paramagnetic mixed layer caused by the diffusion of Cu layer and the change of antiferromagnetic coupling.

• Korean Chemical Engineering Research
• /
• v.47 no.1
• /
• pp.105-110
• /
• 2009

IZO thin films have been deposited on poly(ethylene terephthalate) flexible substrate under varying radio frequency (rf) power, process pressure and thickness of IZO films using rf magnetron sputtering under $Ar/O_2$ gas mix. As the process pressure increased, the deposition rate was slightly increased and the transmittance showed little change, but the resistivity was increased. With increasing rf power, the great increase in deposition rate was observed but the transmittance showed a slight change only, and the resistivity was decreased. In addition, an attempt was made to find the optimal thickness of IZO films under varying the thickness of IZO films at the process conditions of 1 mTorr pressure and 90 W rf power, which showed lowest resistivity. IZO thin films with the thickness of $1,500{\AA}$ showed lowest resistivity and also showed highest transmittance around the wavelength zone of the maximum absorption. The power conversion efficiency of solar cells fabricated using various transparent electrodes with different thicknesses were measured and the solar cell with IZO electrode of $1,500{\AA}$ showed the maximum conversion-efficiency of 2.88 %.

• Journal of the Korea Concrete Institute
• /
• v.18 no.4 s.94
• /
• pp.553-558
• /
• 2006

In this study, fluorine-silicate hybrid type crack reducing agent(FS) consisted of fluorine and silicate compounds applied to concrete mix(specification : 25-30-18) between 0.5% and 2.0% at intervals of 0.5% based on cement weight. Experiments for material properties of concrete such as slump, air content and bleeding with elapsed time were performed. Experiment and elucidation for shrinkage crack resistance as well as adiabatic hydration temperature were also carried out. It was appeared that FS addition contributed to lower bleeding and hydration temperature without disturbance of fresh properties of concrete such as slump and air content compared to non-added concrete. Especially, shrinkage crack resistance of concrete resulted from plastic and drying shrinkage could be effectively reduced by the addition of FS ranging from 1.0% to 1.5%.

• Geophysics and Geophysical Exploration
• /
• v.21 no.3
• /
• pp.139-149
• /
• 2018

The resistivity monitoring is a practical method to resolve changes in resistivity of underground structures over time. With the advance of sophisticated automatic data acquisition system and rapid data communication technology, resistivity monitoring has been widely applied to understand spatio-temporal changes of subsurface. In this study, a new 4D inversion algorithm is developed, which can effectively emphasize significant changes of underground resistivity with time. To overcome the overly smoothing problem in 4D inversion, the Lagrangian multipliers in the space-domain and time-domain are determined automatically so that the proportion of the model constraints to the misfit roughness remains constant throughout entire inversion process. Furthermore, a focusing model constraint is added to emphasize significant spatio-temporal changes. The performance of the developed algorithm is demonstrated by the numerical experiments using the synthetic data set for a time-lapse model.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.6
• /
• pp.539-545
• /
• 2014

Contact resistivity between silver electrodes and the emitter layer of a silicon solar cell wafer has been measured using either the circular transmission line method or the linear transmission line method. The circular transmission line method has an advantage over the linear transmission line method, in that it does not require an additional process for mesa etching to eliminate the leakage current. In contrast, the linear transmission line method has the advantage that its specimen can be acquired directly from a silicon solar cell. In this study, measured resistance data for the calculation of contact resistivity is compared for these two methods, and the mechanism by which the linear transmission line method can more realistically reflect the impact of the width and thickness of a silver electrode on contact resistivity is investigated.