• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.5
• /
• pp.484-491
• /
• 2002

This paper presents the results of a study of voltage-controlled PIN diode attenuators for Ku-band satellite payload and suggests the temperature-compensation method of these attenuators. The PIN diode attenuators are designed using thin-film hybrid techniques. The load resistance for maximum linear characteristics is determined by simulation and measurements. In the case of APD0805, load resistance of 150 $\Omega$ gives attenuator up to 10 dB linear attenuation range per a PIN diode. Also, measurements over temperature of these PIN diode attenuators were performed. From these measurements, designed PIN diode attenuators shows the severe temperature dependency due to forward voltage variation. A temperature compensation method using thermistor is now suggested to compensate the temperature variation of these PIN diode attenuators. This circuit shows good linear characteristics over wide temperature range

• Applied Chemistry for Engineering
• /
• v.9 no.1
• /
• pp.149-154
• /
• 1998

The characteristics of drag reduction and rheological behaviors were investigated using cationic surfactants, whose microstructures are known to change when concentration of the surfactant exceeds CMC. The firstly formed spherical micelles change to rodlike or disklike micelles because of packing between surfactants micells, and of thermodynamic perference. The drag reduction becomes significant when the concentration increases over this micellar transient point. Drag reductions were measured as a function of concentration, and rheological characteristics of the surfactant were further investigated to understand the correlation between their rheological properties and drag reduction. Micelles show the non-Newtonian behavior, and shear thickening behaviors were observed due to the structural development. In addition, structural developments were determined by adding the counter-ion in case of DOBON-G.

• Journal of the Korea Concrete Institute
• /
• v.18 no.3 s.93
• /
• pp.439-445
• /
• 2006

For investigating self-diagnosis applicability, a method based on monitoring the changes in the electrical resistance of hybrid FRP(having electrical property) reinforced concrete has been tested. Then after examining change in the value of electrical resistance of carbon fiber in CFRP(non-hybrid type), CFGFRP and CFAFRP(hybrid type) before and after the occurrence of cracks and fracture in non-hybrid and hybrid FRP reinforced concrete at each flexural weight-stage, the correlations of each factors(the changes in electrical resistance and load as a function of strain, deflection) were analyzed. As the results, it is clarified that when the carbon fiber tows fracture, the electrical resistance of it increase largely, and afterwards hybrid FRP composites can be resist the load due to the presence of the reinforced fiber, for example, glass fiber or aramid fiber tows. Therefore, it can be recognized that hybrid FRP(including carbon fiber) reinforcing bar could be applied for self-diagnosis of fracture in reinforced FRP concrete fracture.

• Journal of the Korean GEO-environmental Society
• /
• v.12 no.1
• /
• pp.51-60
• /
• 2011

Electrical resistivity is applied for understanding details about layers and obtaining basic properties of soils to various measurement devices. The objective of this study is development of TRP(Temperature-compensated Resistivity Probe), analysis about effects of temperature changes during cone penetration test, and observation of characteristics of cone penetration. In order to observation of temperature changes according to a diameter difference of resistivity cone probe, the cone which has wedge type cone tip is made to two types, 2mm and 5mm. Temperature sensor is attached at 15mm below from cone tip because of an electrical interference with elecrical resistance probe. Delectrical connector is used to prevent electric disturbance between motor type penetrating machine and electrical resistivity cone probe. Application tests are carried out in acrylic cell whose diameter is 30cm with uniform Jumunjin sand according to densification caused by blows. The test results indicate that the temperature is increased uniformly during penetration and a tendency, characteristics of cone penetration, is discovered during altering state of soils. This study suggests that the temperature effects and characteristics of penetration should be considered in penetrating tests in order to conduct an accurate ground investigation using TRP(Temperature-compensated Resistivity Probe).

• Journal of the Korea Concrete Institute
• /
• v.18 no.4 s.94
• /
• pp.553-558
• /
• 2006

In this study, fluorine-silicate hybrid type crack reducing agent(FS) consisted of fluorine and silicate compounds applied to concrete mix(specification : 25-30-18) between 0.5% and 2.0% at intervals of 0.5% based on cement weight. Experiments for material properties of concrete such as slump, air content and bleeding with elapsed time were performed. Experiment and elucidation for shrinkage crack resistance as well as adiabatic hydration temperature were also carried out. It was appeared that FS addition contributed to lower bleeding and hydration temperature without disturbance of fresh properties of concrete such as slump and air content compared to non-added concrete. Especially, shrinkage crack resistance of concrete resulted from plastic and drying shrinkage could be effectively reduced by the addition of FS ranging from 1.0% to 1.5%.

• The Korean Journal of Pesticide Science
• /
• v.7 no.1
• /
• pp.25-31
• /
• 2003

Changes of control effect of metalaxyl to potato late blight caused by Phytophthora infestans were examined in potato fields in 2001 and 2002. Control efficacy of metalaxyl was similar to those of dimethomorph and ethaboxam. About 4.9% of the fungal isolates exanlined in 2001 were resistant, 87.8% were intermediate, and 7.3% were sensitive to metalaxyl. Among the isolates collected in 2002, 20.1 % were resistant, 75.5% were intermediate, and 4.3% were sensitive to the chemical. However, most of resistant isolates were isolated from Pyongchanggun Hoenggae area. Eighty eight isolates collected in 2001 were all A1 mating type, while both A1 and A2 mating types were found in 2002. About 85.6% of the isolates collected in 2002 were A1 mating type, but all the rest (A2 mating type) was isolated from Hoenggae area. Increased control efficacy of metalaxyl to potato late blight might be caused by the increase of moderately resistant and sensitive isolates with decreasing the resistant isolate, and the decreased population of A2 mating type which is resistant to metalaxyl.

• Journal of Korea Multimedia Society
• /
• v.6 no.2
• /
• pp.325-331
• /
• 2003

In this paper, we designed a spiral inductor and voltage controlled oscillator with the negative resistor for the bluetooth receiver by using 0.25$\mu\textrm{m}$ 1-poly 5-metal CMOS n-well process. The proposed inductor, which applies multi layer metal structure, is a structure that decreases resistance value by increasing he metal thickness. As the resistance value decreases, the quality factor Q has improved. Also, voltage-controlled oscillator is designed applying 1 port negative resistance, and changes its oscillating frequency by varying outside capacitor values. The simulation results show that oscillating frequency is 2.33~2.58GHz changing from 2pF to 14pF, and the oscillator has oscillating power over 0dBm.

• Journal of IKEEE
• /
• v.11 no.3
• /
• pp.95-99
• /
• 2007

In this study, the electrical characteristics of Symmetric and Asymmetric High Voltage MOSFET(HV-MOSFET) under high temperature were investigated. And, the specific on-resistance, threshold voltage, transconductance, drain current of the HV-MOSFETs were measured over a temperatures range of 300K ${\leq}$ T ${\leq}$400K. From the result of measured data, specific on-resistance increases slightly with increasing temperature. Especially, at high temperature(at 400K) specific on-resistance was increased about 30% than that in room temperature. And, in high temperature condition (at 400K), drain current was decreased about 30%, Also, transconductance(gm) was decreases with increasing temperature.

• Journal of the Korean Magnetics Society
• /
• v.15 no.2
• /
• pp.61-66
• /
• 2005

In order to make submicron cell for spin-injection device, lift-off method using Pt stencil and wet etching was chosen. This approach allows batch fabrication of stencil substrate with electron-beam lithography. It simplifies the process between magnetic film stack deposition and final device testing, thus enabling rapid turnaround in sample fabrication. Submicron junctions with size of $200nm{\times}300nm$ and $500nm{\times}500nm$ 500 nm and pseudo spin valve structure of $CoFe(30{\AA})/Cu(100{\AA})/CoFe(120{\AA}$) was deposited into the nanojunctions. MR ratio was 0.8 and $1.1{\%}$, respectively and spin transfer effect was confirmed with critical current of $7.65{\times}10^7A/cm^2$.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.10
• /
• pp.2066-2070
• /
• 2009

A voltage controlled attenuator using a PIN diode and two resistors of the $\pi$-type fixed attenuator is described in this paper. The proposed variable attenuator operating for a fixed attenuation range has a good input VSWR and a low intermodulation signal. For the low phase shift, a PIN diode is connected with open stub for the purpose of phase compensation. The stub for phase compensation is calculated by the Deloach method and the related circuit theory. This attenuator is easily fabricated on the microstrip and can be normally used in fine control circuits within small attenuation range. The fabricated attenuator for 2110~2170 MHz frequency band has about 4 dB of an attenuation range, $2^{\circ}$ of phase variance, and -20 dB of S11 according to the input voltage from 0 to 2.7 V.